Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.


View this topic in a long page with up to 500 replies per page Create new topic
1 | ... | 15 | 16 | 17 | 18 | 19 | 20 | 21 | 22 | 23 | 24 | 25 | 26 | 27 | 28 | 29 | 30 | 31 | 32 | 33 | 34 | 35 | ... | 42
336 posts

Ultimate Geek


  # 2100393 3-Oct-2018 06:17
Send private message quote this post

I use this for my setup:

 

#Offloading settings
set system offload hwnat disable
set system offload ipsec enable
set system offload ipv4 forwarding enable
set system offload ipv4 gre enable
set system offload ipv4 pppoe enable
set system offload ipv4 vlan enable
set system offload ipv6 forwarding enable
set system offload ipv6 pppoe enable
set system offload ipv6 vlan disable
set system syslog global facility all level notice
set system syslog global facility protocols level debug
set system traffic-analysis dpi enable
set system traffic-analysis export enable


799 posts

Ultimate Geek


  # 2103153 8-Oct-2018 08:56
Send private message quote this post

A few days ago, firmware v1.10.7 has been officially released.





- ISP1: T-OneBox FTTH modem, 1/.5G, full DS, VLAN7, VoIP + ipTV streaming flat

 

- ISP2: 4G/LTE USB modem + TL-MR3020, 100/40M data plan (wireless fallback)

 

- NET: ZBOX nano router, 2 C2960X-48TS-L, 2 GWN7630, GWN7610, EL1600usb

 

- SVR: E3C236 32G/20TB, 2 H2 16G/500GB, HC2 4TB, 2 C2 1TB | 2 HC2 14/1TB

 

- IoT+3D: LoRaWAN, 5G, CCU3 (openHAB/MQTT), 2 Ender-3, UM2E+, UM3, CNC

 

- USR: NUC8i7HVK, EliteBook 840, Aspire E5, N2, Galaxy Tab, mobiles, 2 4K TVs

 

- ipPBX: GRP2613, GO-Box 100, SPA112 (Fax and W-48, a 1948 Siemens phone)


 
 
 
 


257 posts

Ultimate Geek


  # 2103235 8-Oct-2018 11:08
Send private message quote this post

Hi

Trying to set up my ER4 by following this guide. I've come across a few items that don't quite conform with errors emitted when I try to config - whether this has anything to do with the latest Firmware update or not I'm unsure.

I've reset my device back to out of box state and am wanting to setup for use with 2Degrees UFB Ultimate.

I setup PPPoE/password, set VLAN ID to 10, tick Enable default Firewall, make sure Bridge is not selected, save and restart. I start entering all the configure details as detailed but have no luck with any of the IPv6 config entries. Basically all of them are giving some form of error. My question therefore, before I start setting this up, yet again, is - should 'Enable DHCPv6 Prefix Delegation' be in a selected or unselected state?




Mr Snotty
8915 posts

Uber Geek

Moderator
Trusted
Lifetime subscriber

  # 2103253 8-Oct-2018 12:06
Send private message quote this post

@cjmchch I've updated the OP - I noticed there was a mistake in my commands. Try with those.





257 posts

Ultimate Geek


  # 2103303 8-Oct-2018 12:59
Send private message quote this post

michaelmurfy:

@cjmchch I've updated the OP - I noticed there was a mistake in my commands. Try with those.



Thank you

I will.

I’m getting there, albeit slowly...at least I was able to browse the Internet!

336 posts

Ultimate Geek


  # 2104084 9-Oct-2018 18:59
One person supports this post
Send private message quote this post

Missed this as it never went BETA first but v1.0.7 released here

 

EdgeOS Firmware Changelog
====
Supported products
* EdgePoint R6, model: EP-R6
* EdgePoint R8, model: EP-R8
* EdgeRouter X, model: ER-X
* EdgeRouter X SFP, model: ER-X-SFP
* EdgeRouter Lite, model: ERLite-3
* EdgeRouter PoE, model: ERPoe-5
* EdgeRouter, model: ER-8
* EdgeRouter PRO, model: ERPro-8
* EdgeRouter 4, model: ER-4
* EdgeRouter 6P, model: ER-6P
* EdgeRouter 12, model: ER-12
* EdgeRouter Infinity, model: ER-8-XG
====

 

1.10.7 (e50, e100, e200, e300, e1000) Changelog / September 26, 2018
====
Fixes:
- WebGUI: Fix regression in v1.10.6 when false-positive "There was an error upgrading the system"
message was displayed when upgrading via WebGUI
- Interface: Fix bug in ER-Infinity when eth0 VLAN interface dropped 1500 byte incoming packets even
if MTU was set to 1500
- Interface: Fix bug in ER-Infinity when link on SFP-copper module was always ON even if
Ethernet cable was unplugged
- Upgrade: Fixed bug when ER-X/ER-X-SFP/EP-R6 failed to boot new firmware if bad-block was present in
kernel partition when doing firmware upgrade
- Discovery: Add TCP support for UBNT-Discovery protocol used by UNMS
- Bootloader: Show MD5 checksum of current bootloader in "show system boot-image" CLI command
- Bootloader: Add latest bootloader inside EdgeOS firmware image which could be installed
by running "add system boot-image" CLI command.
- LED: Fix LED light/blinking behaviour (required bootloader upgrade)
- Bootloader: Fix bug when "show system boot-image" CLI command failed in ER-4/ER-6P/ER-12
- OSPFv3: Fix bug when "instance-id" was not updated
- VPLS: Fix bug when ER failed to establish with VPLS session with non-UBNT routers because
it did not comply with RFC-4761
- Interface: Fix bug that caused "Commit failure" when deleting VLAN interace with custom MTU
- DHCP: prevent DHCP clients from registering hostnames "unifi", "wpad" and "isatap".
Hosts with these names can still obtain DHCP leases, but their hostname will be ignored, for both
dnsmasq and dhcpd as DHCP server.
- DHCP: Fixed bug when DHCP server failed to restart during reconfiguration with
"There's already a DHCP server running" message in syslog
- DHCP: Fix bug when illegal DHCP server configuration succeeded and caused `dhcpd` to silently die
- DNS: Fix bug when DNS forwarding via DHCP client interface did not work if DHCP lease
was acquired after configuring DNS forwarding
- CLI: Fix bug when "set" command failed after doing "discard"


256 posts

Ultimate Geek

Subscriber

  # 2104167 9-Oct-2018 22:55
Send private message quote this post

michaelmurfy:

 

@cjmchch I've updated the OP - I noticed there was a mistake in my commands. Try with those.

 

 

 

 

good evening Michael, 

 

 

 

i tried your updated method to enable ipv6, how do you normally verified ipv6 has been able or not?

 

i can see there is new line under my normal ipv4 address, they started with fe80::2d28:

 

but is it normal to have "::"?

 

 

 

thanks,

 

Sam


 
 
 
 




Mr Snotty
8915 posts

Uber Geek

Moderator
Trusted
Lifetime subscriber

  # 2104168 9-Oct-2018 23:10
Send private message quote this post

iamsammajor:

 

i tried your updated method to enable ipv6, how do you normally verified ipv6 has been able or not?

 

i can see there is new line under my normal ipv4 address, they started with fe80::2d28:

 

but is it normal to have "::"?

 

Your router should show a fe80:: address under the PPPoE connection and a subnet under your local LAN port. Try rebooting it. I can see your post didn't come via IPv6 so it isn't working yet (tip - Geekzone's logo will change when accessed via IPv6).

 

Ensure you've modified the commands for your setup - they're an example only. Also read the bit regarding 2degrees IPv6 using a /48 subnet if you don't have a static IP with them. If you want to try again then use the clear commands at the top of the IPv6 part, reboot your router and try again.

 

Also if you want to learn more about IPv6 I recommend completing this course: https://ipv6.he.net/certification/ - you get a free shirt upon completion. Lets see if anyone can match my score:

 





256 posts

Ultimate Geek

Subscriber

  # 2104170 9-Oct-2018 23:31
Send private message quote this post

michaelmurfy:

 

iamsammajor:

 

i tried your updated method to enable ipv6, how do you normally verified ipv6 has been able or not?

 

i can see there is new line under my normal ipv4 address, they started with fe80::2d28:

 

but is it normal to have "::"?

 

Your router should show a fe80:: address under the PPPoE connection and a subnet under your local LAN port. Try rebooting it. I can see your post didn't come via IPv6 so it isn't working yet (tip - Geekzone's logo will change when accessed via IPv6).

 

Ensure you've modified the commands for your setup - they're an example only. Also read the bit regarding 2degrees IPv6 using a /48 subnet if you don't have a static IP with them. If you want to try again then use the clear commands at the top of the IPv6 part, reboot your router and try again.

 

Also if you want to learn more about IPv6 I recommend completing this course: https://ipv6.he.net/certification/ - you get a free shirt upon completion. Lets see if anyone can match my score:

 

 

 

 

 

a green "ipv6" was there on top of the geekzone logo, but gone after rebooting,

 

i did see a fe80:: address under the PPPoE connection, so as under eth1, 

 

i did use "set prefix-length /48"

 

 

 

 

 

 

 

 


461 posts

Ultimate Geek

Subscriber

  # 2104200 10-Oct-2018 06:41
Send private message quote this post

The HE certification is great, you'll learn a lot. I wear my shirt quite often.

 

You can also try IPv6 only sites, like https://ipv6.google.com to test your connectivity. Bear in mind, you're browser can and will fall back to IPv4 at times. You can also use https://test-ipv6.com/ to test your connection (there are others, you can google them).

 

 


256 posts

Ultimate Geek

Subscriber

  # 2106617 12-Oct-2018 09:03
Send private message quote this post

i can see ipv6 address in the router and every client, can also go https://ipv6.google.com , but when i go test-ipv6.com, it fails. also there is no change in geekzone logo


257 posts

Ultimate Geek


  # 2106765 12-Oct-2018 13:44
Send private message quote this post

I'm up and running with my EdgeRouter4 using IPv4 only - kept stalling for some reason when trying to setup on IPv6 following the instructions.

Everything is working except for 2 small issues - Port Forwarding and open ports. I think it is most likely because of my settings in relation to setting the correct WAN interface. This is where I'm a bit confused and hoping someone can give me the correct answer.

I use 2Degrees UFB which has a WAN eth0 setting of pppoe with vlan 10 set.

When it comes to setting Firewall Policies and Port Forwarding is my WAN interface eth0. eth0.10 or pppoe?

I have set a port forwarding rule to one of my computers which remains closed when I test it. This is why I think my interface settings are wrong. I have it set to eth0.10

The other small issue is that I have both port 80 and 443 open that I never opened, and want closed. How best to achieve that?

Thanks in advance for any help



Resolved this myself - WAN interface is PPPoE!

I figured that if I couldn't open ports that I set and the firewall wasn't blocking ports it was meant to then it had to be the WAN interface setting that was wrong...

257 posts

Ultimate Geek


  # 2109101 16-Oct-2018 20:14
Send private message quote this post

Just wondering Michael Murphy if there is a way on the edgerouter 4 to show uptime of my internet connectivity or some other way of determining if my internet connection drops off.

I've had a couple of recent issues where one of my 24/7 computers has failed to connect to an external range of servers and times out. I'm trying to isolate whether it is an issue with regard the connection or a computer/internal network problem issue or not.

defiant
1034 posts

Uber Geek

Lifetime subscriber

  # 2109118 16-Oct-2018 21:11
Send private message quote this post

You can integrate the EdgeRouter with UNMS which will log outages for you https://unms.com/

 

You have to install it on a Linux server, and it runs on its own docker container


257 posts

Ultimate Geek


  # 2109119 16-Oct-2018 21:13
Send private message quote this post

Thanks for that - the issues I'm having are on a CentOS server so will install and run from there. Cheers for the info.

1 | ... | 15 | 16 | 17 | 18 | 19 | 20 | 21 | 22 | 23 | 24 | 25 | 26 | 27 | 28 | 29 | 30 | 31 | 32 | 33 | 34 | 35 | ... | 42
View this topic in a long page with up to 500 replies per page Create new topic



Twitter and LinkedIn »



Follow us to receive Twitter updates when new discussions are posted in our forums:



Follow us to receive Twitter updates when news items and blogs are posted in our frontpage:



Follow us to receive Twitter updates when tech item prices are listed in our price comparison site:





News »

Chorus to launch Hyperfibre service
Posted 18-Nov-2019 15:00


Microsoft launches first Experience Center worldwide for Asia Pacific in Singapore
Posted 13-Nov-2019 13:08


Disney+ comes to LG Smart TVs
Posted 13-Nov-2019 12:55


Spark launches new wireless broadband "Unplan Metro"
Posted 11-Nov-2019 08:19


Malwarebytes overhauls flagship product with new UI, faster engine and lighter footprint
Posted 6-Nov-2019 11:48


CarbonClick launches into Digital Marketplaces
Posted 6-Nov-2019 11:42


Kordia offers Microsoft Azure Peering Service
Posted 6-Nov-2019 11:41


Spark 5G live on Auckland Harbour for Emirates Team New Zealand
Posted 4-Nov-2019 17:30


BNZ and Vodafone partner to boost NZ Tech for SME
Posted 31-Oct-2019 17:14


Nokia 7.2 available in New Zealand
Posted 31-Oct-2019 16:24


2talk launches Microsoft Teams Direct Routing product
Posted 29-Oct-2019 10:35


New Breast Cancer Foundation app puts power in Kiwi women's hands
Posted 25-Oct-2019 16:13


OPPO Reno2 Series lands, alongside hybrid noise-cancelling Wireless Headphones
Posted 24-Oct-2019 15:32


Waikato Data Scientists awarded $13 million from the Government
Posted 24-Oct-2019 15:27


D-Link launches Wave 2 Unified Access Points
Posted 24-Oct-2019 15:07



Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.


Support Geekzone »

Our community of supporters help make Geekzone possible. Click the button below to join them.

Support Geezone on PressPatron



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.

Alternatively, you can receive a daily email with Geekzone updates.