Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.




152 posts

Master Geek
+1 received by user: 13


Topic # 57057 1-Feb-2010 19:49
Send private message

Hi All

I moved into my new place in December and are working through my house renovation and my plans for wiring the phones, network and TV through the house as I take off the gibboard room by room.

I have complete internal roof access  (concrete tile roof) and access under the floorboards to 1/2 the house. I want to centralise the SKY and UHF/VHF and keep any cabels outside out of sight. I plan to have the cetralised point in the basement along with the comms cabenet for the phone/network.

Currently I only have a single RG59 cable to the single areial on the roof (guessing UHF)

I am a bit dubious of sky installers as I have had them install twice for me and they dont seem to be in it for the astetics so are thinking maybe I have the cable there ready for them once they arrive.

I know I need to run 3 x RG6 cabels to the roof but are looking for suggestions on the best way to do this to keep the cable tidy - i.e is there a way to go through the concrete tiles??

open to suggestions. thanks :)

Create new topic
2950 posts

Uber Geek
+1 received by user: 438

Trusted
Subscriber

  Reply # 295282 1-Feb-2010 22:52
Send private message

Oh, with the right sort of drill you can certainly go through the concrete. You'll probably still need a Sky installer on hand though, as they seem to be very particular about where they'll install the dish.




I finally have fibre!  Had to leave the country to get it though.


3006 posts

Uber Geek
+1 received by user: 722


  Reply # 295308 2-Feb-2010 08:47
Send private message

If you stick you head up into the roof cavity and have a good look round in the middle of the day you may find a cap in the morter so you dont actually have to drill through any actual tiles.

You may be able to find a gap in the morter allowing you to run wiring out under a tile close to where the dish is one the roof, alternatively you can chip out the morter yourself. This preserves the tile face ( which reguires you seal the joint to prevent water ingress), slipping under a tile means that if your siliconing fails, it is unlikely the water will travel up to get into the roof.



 
 
 
 


Try Wrike: fast, easy, and efficient project collaboration software
2260 posts

Uber Geek

Trusted

  Reply # 295309 2-Feb-2010 08:49
Send private message

yeah two options:

- either drill through the concrete and use a grommet and then seal it with RTV silicone
- lift up the tile at the lower trailing edge and make a small indent in it, then feed the cable beneath the tile through the protective black layer into the house

I did option two and it's never leaked, it's been perfect :) and looks the part




I have moved across the ditch.  Now residing in Melbourne as a VOIP/Video Technical Trainer/Engineer. 

2260 posts

Uber Geek

Trusted

  Reply # 295311 2-Feb-2010 09:03
Send private message

wellygary: If you stick you head up into the roof cavity and have a good look round in the middle of the day you may find a cap in the morter so you dont actually have to drill through any actual tiles.

You may be able to find a gap in the morter allowing you to run wiring out under a tile close to where the dish is one the roof, alternatively you can chip out the morter yourself. This preserves the tile face ( which reguires you seal the joint to prevent water ingress), slipping under a tile means that if your siliconing fails, it is unlikely the water will travel up to get into the roof.





whoops, was typing up my reply when yours came up :) 





I have moved across the ditch.  Now residing in Melbourne as a VOIP/Video Technical Trainer/Engineer. 

3264 posts

Uber Geek
+1 received by user: 531

Lifetime subscriber

  Reply # 295320 2-Feb-2010 10:13
Send private message

I'm assuming you have no Sky installation at the moment.
As far as the installers being particular about the position of dish goes, they will try and put it in a position that requires the minimum material use and effort (in my experience). That is because Sky pay them a minimal fixed rate for each installation. They will probably suggest mounting on a gable, soffit or wall because that is easier for them. If you have a look at your neighbour's dishes that will give you an indication of how the dish needs to be aligned to get a clear view of the satellite and then YOU decide where you would like the dish to go.
For my own installation I pre-drilled all the required cable runs and had purchased wall plates so that when the installer arrived I was able to pull the cable through for him while he mounted the dish (where I directed it to be). Current installations are a thicker multi-lead cable so allow plenty of room in any predrill.




Areas of Geek interest: Home Theatre, HTPC, Android Tablets & Phones, iProducts.

3267 posts

Uber Geek
+1 received by user: 77

Trusted

  Reply # 295412 2-Feb-2010 15:18
Send private message

I got a great installer, he placed the dish completely out of site. He could have placed it at the front of the house and saved more than half the cable, but instead he placed it on the South side and low down but still gets maximum signal and seldom rain fade (East Auckland gets less rain anyway). Can barely see it from the road and (large) back yard. Cable runs in the rain gutter to the back of the house and around to about the middle of the back wall, goes down attached to down pipe, under house, and then almost to the front of the house before coming up through the floor with lots of extra cable for if/when we want to move the set top box. Some installer take pride in what they do. Very tidy job considering a 1960's 2-bedroom home that is beyond renovateability (unless for a batch) and will eventually be removed to build a decent size house.




You can never have enough Volvos!


Create new topic



Twitter »

Follow us to receive Twitter updates when new discussions are posted in our forums:



Follow us to receive Twitter updates when news items and blogs are posted in our frontpage:



Follow us to receive Twitter updates when tech item prices are listed in our price comparison site:





News »

IBM leads Call for Code to use cloud, data, AI, blockchain for natural disaster relief
Posted 25-May-2018 14:12


New FUJIFILM X-T100 aims to do better job than smartphones
Posted 24-May-2018 20:17


Stuff takes 100% ownership of Stuff Fibre
Posted 24-May-2018 19:41


Exhibition to showcase digital artwork from across the globe
Posted 23-May-2018 16:44


Auckland tops list of most vulnerable cities in a zombie apocalypse
Posted 23-May-2018 12:52


ASB first bank in New Zealand to step out with Garmin Pay
Posted 23-May-2018 00:10


Umbrellar becomes Microsoft Cloud Solution Provider
Posted 22-May-2018 15:43


Three New Zealand projects shortlisted in IDC Asia Pacific Smart Cities Awards
Posted 22-May-2018 15:14


UpStarters - the New Zealand tech and innovation story
Posted 21-May-2018 09:55


Lightbox updates platform with new streaming options
Posted 17-May-2018 13:09


Norton Core router launches with high-performance, IoT security in New Zealand
Posted 16-May-2018 02:00


D-Link ANZ launches new 4G LTE Dual SIM M2M VPN Router
Posted 15-May-2018 19:30


New Panasonic LUMIX FT7 ideal for outdoor: waterproof, dustproof
Posted 15-May-2018 19:17


Ryanair Goes All-In on AWS
Posted 15-May-2018 19:14


Te Papa and EQC Minecraft Mod shakes up earthquake education
Posted 15-May-2018 19:12



Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.

Alternatively, you can receive a daily email with Geekzone updates.