Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.




691 posts

Ultimate Geek
+1 received by user: 30


Topic # 143967 3-May-2014 11:11
Send private message

We've ongoing problems with the overflow spilling water as the ballcock hasn't cut off.

I think it's installed too high in the tank.  is it OK to move it down an inch or two  i.e. cut a new hole for it in the tank?

It's a brass one and I've bent the arm down as much as possible. Now I'm told this puts more pressure on the washer which gives out sooner and then leaks.

Create new topic
1650 posts

Uber Geek
+1 received by user: 303

Subscriber

  Reply # 1035930 3-May-2014 11:33
One person supports this post
Send private message

Oooh, can't imagine anyone has had to move the ballcock assembly down.

You omit to say whether you have changed the washer! If you have, and it still leaks, you need to buy a new ballcock assembly I would say.

Just had another thought. Check that the ball is not half full of water - it has happened.

552 posts

Ultimate Geek
+1 received by user: 215

Subscriber

  Reply # 1035931 3-May-2014 11:34
Send private message

Before you go to the trouble of cutting a new hole, check the action of the ballcock.
In my experience they (esp the brass type) do fail.
And it won't cause early failure by bending the float arm as it'll still cut off at the same pressure, it's just likely the pressure required is increasing due to wear or hardening.
Can you watch as it fills to the shutoff point and see what happens?

 
 
 
 


2155 posts

Uber Geek
+1 received by user: 206


  Reply # 1035937 3-May-2014 11:59
Send private message

Occasionally you may find that the nipple is loose so water is leaking past it even though the washer is sealed tight against the end. It screws in from the input pipe end.



691 posts

Ultimate Geek
+1 received by user: 30


  Reply # 1035939 3-May-2014 12:02
Send private message

When it failed last time I fixed it by changing the washer. That was maybe a year ago...

I bought a new (plastic) unit and can see if filling. By the time it shuts off the water level is past the overflow outlet. That's made me think
moving the whole thing down would work.  Is there a recommended distance between the outlet and where the assy sits ?

I could also try another washer in the brass one.  The ball hasn't got water in it.


2358 posts

Uber Geek
+1 received by user: 393


  Reply # 1035946 3-May-2014 12:26
Send private message

Its nearly always the washer and seat part rather than the float.
So provided the ballcock hasnt got water in it check the washer - bet that's causing the shut off problem.




Nothing is impossible for the man who doesn't have to do it himself - A. H. Weiler

1368 posts

Uber Geek
+1 received by user: 289

Trusted

  Reply # 1035949 3-May-2014 12:37
One person supports this post
Send private message

I'm surprised all these posts got past the geekzone rude word checker..

2155 posts

Uber Geek
+1 received by user: 206


  Reply # 1035952 3-May-2014 12:44
Send private message

ADKM:I bought a new (plastic) unit and can see if filling. By the time it shuts off the water level is past the overflow outlet.


If you've changed the whole ballcock unit did you adjust the float level?

2831 posts

Uber Geek
+1 received by user: 781

Trusted
Subscriber

  Reply # 1035958 3-May-2014 13:05
Send private message

I had exactly this problem with my ancient header tank system (2 large tanks side by side) recently. One wouldn't shut off and the overflow was overfilling the other tank which was then spilling out of the overflow pipe. I took the lid off the tanks and saw straight away some silly person had bent one of the arms (on the tank which wasn't shutting off) indicating there'd been a problem before but they didn't want to fix it. It was an easy fix:

1. Shut off water at toby (or at tank if you have a shut off valve there)
2. Disassemble mechanism
3. Carefully straighten out arm as much as possible
4. Take end of assembly to local plumbing shop to get correct size washer (mine was 70 cents)
5. After fitting washer, reassemble mechanism
6. Turn water back on.


1426 posts

Uber Geek
+1 received by user: 109

Subscriber

Reply # 1035961 3-May-2014 13:12
Send private message

we used to have heaps of trouble with the ballcock valve due to grit getting in and chewing seals out.   In the end I installed a Fluidmaster unit and never looked back.  Easy fit and adjust then forget about it




HTPC Intel Pentium G3258 cpu, Gigabyte H97n-wifi motherboard, , 8GB DDR3 ram, onboard  graphics. Hauppuage HVR 5500 tuner,  Silverstone LC16M case, Windows 10 pro 64 bit using Nextpvr and Kodi


4323 posts

Uber Geek
+1 received by user: 1203


  Reply # 1035988 3-May-2014 14:05
Send private message

Can you post a photo of the current setup - is it one of the fluidmaster plastic float valves?



691 posts

Ultimate Geek
+1 received by user: 30


  Reply # 1035993 3-May-2014 14:33
Send private message

Many thanks everyone. :)  I've just replaced the washer and all seems OK. BUT this time I realised it unscrews to fit the washer neatly in. Last
time I forced it in, wondering why the 'right' thing was too big. Duh!   Maybe this will last longer.

The arm is bent a bit, and I couldn't see how to get at the nipple  (quiet, jonb!!!) or the float.  Also the hole allowed me to slot the assy down a little.
Now the overflow is a good inch or two above the water.  Previously it was lapping out (because the washer was leaking I guess).

Hopefully I can return the new unit.
Thanks again, help much appreciated.


2155 posts

Uber Geek
+1 received by user: 206


  Reply # 1036018 3-May-2014 14:56
Send private message

ADKM:
The arm is bent a bit, and I couldn't see how to get at the nipple  (quiet, jonb!!!) or the float.  Also the hole allowed me to slot the assy down a little.
Now the overflow is a good inch or two above the water.  Previously it was lapping out (because the washer was leaking I guess).




Don't fixate on how bent the arm is, it is a legitimate way of setting the desired level. You've explained that the leak was probably how the washer was forced into the holder but the stainless steel valve seat screws in from the input side. You'd have to take the unit out to see the screwdriver slot in the end of it.

gzt

8885 posts

Uber Geek
+1 received by user: 1186


  Reply # 1036160 3-May-2014 19:17
One person supports this post
Send private message

Replace the cistern washer at the same time, it will almost certainly go very soon after.

97 posts

Master Geek
+1 received by user: 1


  Reply # 1038340 7-May-2014 13:34
Send private message

You can get bigger float too

Create new topic



Twitter »

Follow us to receive Twitter updates when new discussions are posted in our forums:



Follow us to receive Twitter updates when news items and blogs are posted in our frontpage:



Follow us to receive Twitter updates when tech item prices are listed in our price comparison site:





News »

Avondale College students at top of Microsoft Office Specialist World Championship
Posted 21-Aug-2017 14:11


Garmin introduces inReach SE+ and inReach Explorer+
Posted 21-Aug-2017 14:05


Public Wi-Fi plus cloud file sharing
Posted 18-Aug-2017 11:20


D-Link NZ launches professional Wireless AC Wave 2 Access Point for businesses
Posted 17-Aug-2017 19:25


Garmin introduces the Rino 700 five-watt two-way handheld radio
Posted 17-Aug-2017 19:04


Garmin announces the Foretrex 601 and Foretrex 701 Ballistic Edition for outdoor and tactical use
Posted 17-Aug-2017 19:02


Brightstar announces new distribution partnership with Samsung Knox platform in Australia
Posted 17-Aug-2017 17:07


Free gig-enabled WiFi network extends across Dunedin
Posted 17-Aug-2017 17:04


Samsung expands with connect Gear S3 Frontier
Posted 17-Aug-2017 15:55


Fact-checking Southern Cross Next cable is fastest to USA
Posted 17-Aug-2017 13:57


Thurrott says Microsoft Surface is dead last for reliability
Posted 16-Aug-2017 15:19


LibreOffice 5.4 works better with Microsoft Office files
Posted 16-Aug-2017 13:32


Certus launches Cognition
Posted 14-Aug-2017 09:31


Spark adds Cambridge, Turangi to 4.5G network
Posted 10-Aug-2017 17:55


REANNZ network to receive ongoing Government funding through to 2024
Posted 10-Aug-2017 16:05



Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.

Alternatively, you can receive a daily email with Geekzone updates.