Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.

neb



670 posts

Ultimate Geek
+1 received by user: 115

Lifetime subscriber

Topic # 230437 23-Feb-2018 17:46
Send private message

I need to rack-mount a pile of assorted small embedded devices (weather monitoring, stratum 1 clock, ADSB, AIS, assorted devices used for kernel test builds, ethernet serial bridges, and all manner of other stuff) that currently take up about 3m of bench space. Unfortunately no-one makes racks for things the size of a book, and looking at various things that could pressed into service, e.g. steel mesh paper trays, hasn't turned up anything useful, at least not that you can get in NZ. So it looks like the best bet is to roll my own using alu stock. The idea was to build a series of shelves using alu angle and bar stock and put alu mesh over the top for the devices to sit on, as per the incredibly high-tech CAD drawing below:

 

 

 

 

Then I'd assemble a bunch of these shelves into a rack using more alu angle as legs.

 

 

Does anyone have any thoughts on this? Is there a better way to build up the shelves? Does someone make ready-made miniature-size equipment racks of this kind?

 


Create new topic
3985 posts

Uber Geek
+1 received by user: 513

Trusted

  Reply # 1963119 23-Feb-2018 18:16
Send private message

No dimensions?

What about a 9u rack? With shelves. Either the one with doors or not. I have a wall mounted one 19” wise.

Or plastic cabinet with pull out drawers?




Previously known as psycik

NextPVR: 
Gigabyte AMD A8 Brix --> Samsung LA46A650D via HDMI, NextPVR,
OpenHAB: ODroid C2 eMMC DriveOpenHAB with Aeotech ZWave Controller, Raspberry PI, Wemos D1 Mini, Zwave and Bluetooth LE Sensors
Media:Chromecast v2, ATV4, Roku3, HDHomeRun Dual
Windows 2012 
Host (Plex Server/Crashplan): 2x2TB, 2x3TB, 1x4TB using DriveBender, Samsung 850 evo 512 GB SSD, Hyper-V Server with 1xW10, 1xW2k8, 2xUbuntu 16.04 LTS, Crashplan, NextPVR channel for Plex,NextPVR Metadata Agent and Scanner for Plex


neb



670 posts

Ultimate Geek
+1 received by user: 115

Lifetime subscriber

  Reply # 1963494 24-Feb-2018 15:24
Send private message

davidcole: No dimensions?

What about a 9u rack? With shelves. Either the one with doors or not. I have a wall mounted one 19” wise.

Or plastic cabinet with pull out drawers?

 

 

9U racks range from expensive to eyewateringly expensive, they'd be pretty close to what I'm after but I can build one for $50-100, which isn't anywhere close to what a rack + shelving would cost.

 

 

Plastic won't do, this stuff generates a fair bit of heat, having plastic exposed to it for long periods will warp/crack it.

neb



670 posts

Ultimate Geek
+1 received by user: 115

Lifetime subscriber

  Reply # 1964755 26-Feb-2018 20:30
Send private message

Currently also toying with the idea of building it from 2020 t-slot aluminium, mainly because it's readily available to deal with the 3D printer/maker market. It's a bit pricier, but there's a lot less metalworking involved, just bolt it together from a pile of 2020 extrusion. Downside is it looks pretty engineering-shop...

epr

131 posts

Master Geek
+1 received by user: 40


  Reply # 1964761 26-Feb-2018 20:45
Send private message

Racks on trade me can be an alright price how much are you looking to spend so people don't make suggestions that are not in your budget.

neb



670 posts

Ultimate Geek
+1 received by user: 115

Lifetime subscriber

  Reply # 1964768 26-Feb-2018 21:07
Send private message

epr: Racks on trade me can be an alright price how much are you looking to spend so people don't make suggestions that are not in your budget.

 

 

For the DIY option I was looking at something max 300mm deep, about 400 wide, and 350-400 high, with three shelves. Looks like I could built it for about $150 in materials if I use 2020, or about $100 if I use basic alu stock. So something roughly in that range.

4975 posts

Uber Geek
+1 received by user: 1586


  Reply # 1964772 26-Feb-2018 21:13
Send private message

This sort of thing?

 

https://www.trademe.co.nz/computers/networking-modems/other/auction-1556010431.htm

 

Get them quite a bit cheaper than that sometimes if you're prepared to search TM too.


neb



670 posts

Ultimate Geek
+1 received by user: 115

Lifetime subscriber

  Reply # 1964797 26-Feb-2018 21:22
Send private message

Jaycar had them on special a while back for a lot less (just dumping old stock, about $30 for a nice 9U), however they're enclosed, I want an open frame since some of the devices generate a fair bit of heat, and most have blinkenlights that need monitoring. So it was more open shelves than a fully enclosed rack.

neb



670 posts

Ultimate Geek
+1 received by user: 115

Lifetime subscriber

  Reply # 2019820 21-May-2018 14:32
Send private message

So it's finished, wanted to post a few photos. Since it's a DIY rather than pre-build I got it pretty much exactly how I wanted it, only problem was the supplier of the perforated steel sheets sent 3mm instead of 1.5mm and it's been stored on a drum or something so it wasn't flat, and the thickness meant I couldn't get it flat. It's most obvious on the bottom one. Rest turned out OK.

 

 

 

 

 

 

 

 


4784 posts

Uber Geek
+1 received by user: 1932


  Reply # 2019862 21-May-2018 15:03
Send private message

neb: and the thickness meant I couldn't get it flat.   

 

Did you try driving over it on the garage floor?  Flattens most things.  You need to do it few times for things wider than the car tyres.





Mike

2012 posts

Uber Geek
+1 received by user: 330

Lifetime subscriber

  Reply # 2019867 21-May-2018 15:09
Send private message

Hurts my OCD, which I just diagnosed today.


581 posts

Ultimate Geek
+1 received by user: 105

Subscriber

  Reply # 2019879 21-May-2018 15:22
Send private message

Great job!

 

Would you take orders? :-)


neb



670 posts

Ultimate Geek
+1 received by user: 115

Lifetime subscriber

  Reply # 2019911 21-May-2018 15:43
Send private message

MikeAqua:

neb: and the thickness meant I couldn't get it flat.   

 

Did you try driving over it on the garage floor?  Flattens most things.  You need to do it few times for things wider than the car tyres.

 

 

Tried clamping it both flat and later with a slight concave flex on it, but it just sprang back to curved the wrong way afterwards. Eventually I decided I'd just live with it, it's only really bad on the bottom-most plate.

neb



670 posts

Ultimate Geek
+1 received by user: 115

Lifetime subscriber

  Reply # 2019912 21-May-2018 15:44
One person supports this post
Send private message

gcorgnet:

Would you take orders? :-)

 

 

It was a fair bit of work unfortunately, once you add the labour to the cost it's not terribly economical any more even though the raw materials were relatively cheap. It was fun making it, but not really viable as a commercial proposition.

Create new topic

Twitter »

Follow us to receive Twitter updates when new discussions are posted in our forums:



Follow us to receive Twitter updates when news items and blogs are posted in our frontpage:



Follow us to receive Twitter updates when tech item prices are listed in our price comparison site:





News »

Intel introduces new NUC kits and NUC mini PCs
Posted 16-Aug-2018 11:03


The Warehouse leaps into the AI future with Google
Posted 15-Aug-2018 17:56


Targus set sights on enterprise and consumer growth in New Zealand
Posted 13-Aug-2018 13:47


Huawei to distribute nova 3i in New Zealand
Posted 9-Aug-2018 16:23


Home robot Vector to be available in New Zealand stores
Posted 9-Aug-2018 14:47


Panasonic announces new 2018 OLED TV line up
Posted 7-Aug-2018 16:38


Kordia completes first live 4K TV broadcast
Posted 1-Aug-2018 13:00


Schools get safer and smarter internet with Managed Network Upgrade
Posted 30-Jul-2018 20:01


DNC wants a safer .nz in the coming year
Posted 26-Jul-2018 16:08


Auldhouse becomes an AWS Authorised Training Delivery Partner in New Zealand
Posted 26-Jul-2018 15:55


Rakuten Kobo launches Kobo Clara HD entry level reader
Posted 26-Jul-2018 15:44


Kiwi team reaches semi-finals at the Microsoft Imagine Cup
Posted 26-Jul-2018 15:38


KidsCan App to Help Kiwi Children in Need
Posted 26-Jul-2018 15:32


FUJIFILM announces new high-performance lenses
Posted 24-Jul-2018 14:57


New FUJIFILM XF10 introduces square mode for Instagram sharing
Posted 24-Jul-2018 14:44



Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.

Alternatively, you can receive a daily email with Geekzone updates.