Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.

neb



668 posts

Ultimate Geek
+1 received by user: 114

Lifetime subscriber

Topic # 230588 3-Mar-2018 10:38
Send private message

I've got a 20-22mm hole under the eaves of the house with a 12mm alu bar (that containg wiring) coming out of it:

 

 

 

 

and I'm looking at ways of sealing it up. Standard acrylic sealant won't do it because of the size of the gap, so I'm thinking of...

 

 

1. Gorilla foam with sealant over the top.

 

 

2. Put a 16mm alu channel over the top of it, which will fill the 20mm hole to a level where I can use acrylic sealant.

 

 

3. Cut a 20mm dowel in half to form a plug, and seal up the remaining gap.

 

 

Any thoughts on that, or any other ideas? None are perfect, but I'm sorta leaning towards the gorilla foam at the moment, although it's horrible stuff to remove if I ever need to replace anything.

 


Filter this topic showing only the reply marked as answer View this topic in a long page with up to 500 replies per page Create new topic
 1 | 2
21287 posts

Uber Geek
+1 received by user: 4296

Trusted
Subscriber

  Reply # 1967462 3-Mar-2018 11:16
Send private message

Why not just bog it up?





Richard rich.ms

189 posts

Master Geek
+1 received by user: 104


  Reply # 1967463 3-Mar-2018 11:21
One person supports this post
Send private message

Yep Builders Bog and paint.

 

https://www.bunnings.co.nz/turbo-builder-s-bog-500ml_p00712784


2386 posts

Uber Geek
+1 received by user: 1163

Lifetime subscriber

  Reply # 1967467 3-Mar-2018 11:26
One person supports this post
Send private message

I'd 3D-print a neat cover for the whole thing, and screw/glue it in place.

 

 


416 posts

Ultimate Geek
+1 received by user: 87


  Reply # 1967468 3-Mar-2018 11:31
Send private message

cruxis:

 

Yep Builders Bog and paint.

 

https://www.bunnings.co.nz/turbo-builder-s-bog-500ml_p00712784

 

 

Put a balled up bit of chicken wire in the hole then use the Builders Bog or crunched up newspaper and Builders Bog. I've done both before especially on bigger holes.





iMac 27" (late 2013), Airport Time Capsule + Airport Express, iPhone7, iPad6, iPad Mini2

 

Panasonic Blu-ray PVR DMR-BWT835 + Panasonic Viera TH-L50E6Z, Chromecast Ultra


1164 posts

Uber Geek
+1 received by user: 238

Subscriber

  Reply # 1967494 3-Mar-2018 12:27
4 people support this post
Send private message

  • Make a template that is slightly wider than the hole out of cardboard, timber etc.
  • Drill a screw into the middle of the template
  • Cover the surface of the template with adhesive (ados, gorilla grip, builders nails.
  • Insert it into the hole - the screw lets you keep hold of it.
  • Pull it towards you and the adhesive will stick it against the inside of the hole.
  • LEt it dry and remove the screw.
  • Then bog / putty / plaster over the top of that.

 

 

Using a template will give you a much better base than just filling the hole with bog - it gives a foundation to put your filler onto.

 

A template could be two sticks of wood  - one above the conduit and one below then cross hatch a couple of other bits of wood on top. Chicken wire etc is good but a big hole presents problems if the filler has no base to sit on.

 

 

 

Gorrilla or sellys expanding foam is another option. Pump it in and let her expand to fill the whole. However the same issue applies - what does it hang onto. Once dry it can be sanded flat / into shape.

 

Good article on different filler types here. Pros and cons.  -> https://www.hunker.com/13401515/the-best-wood-filler-for-large-holes

 

 

 

The really correct artisan way:

 

  • Enlarge the hole - square it up.
  • Cut a piece of wood to fit the newly enlarged hole.
  • Put wings on two sides of the back of the wood plug
  • Put adhesive onto the fronts of the wings
  • Insert into hole and pull it forward to the wings connect firmly inside the hole. (a screw in the centre of the plug helps pull it forward)
  • Paint and putty over the minor cracks left.
  •  

 

 





nunz

1164 posts

Uber Geek
+1 received by user: 238

Subscriber

  Reply # 1967497 3-Mar-2018 12:33
Send private message

FineWine:

 

cruxis:

 

Yep Builders Bog and paint.

 

https://www.bunnings.co.nz/turbo-builder-s-bog-500ml_p00712784

 

 

Put a balled up bit of chicken wire in the hole then use the Builders Bog or crunched up newspaper and Builders Bog. I've done both before especially on bigger holes.

 

 

<humour>

 

Looking at your signature - tag line. Are you an agent provocateur for France?  After France bombed the rainbow warrior I am surprised they can take a moral stance on green issues :)    The temptation to fill in the form as coming from Syria or similar  was really tempting.

 

</humour>

 

Wish NZ would step up their game in this regard.

 

 

 

 





nunz

20 posts

Geek
+1 received by user: 6


  Reply # 1967582 3-Mar-2018 17:10
Send private message

Why not just use some MS sealant? I've done 40mm holes with it before. It sticks like sh**.

neb



668 posts

Ultimate Geek
+1 received by user: 114

Lifetime subscriber

  Reply # 1967621 3-Mar-2018 19:08
Send private message

nunz:

Make a template ...

 

 

Ah, that's the missing magic! I'd mentally crossed out bogging it up because the filler I've worked with in the past (one-component, admittedly, I'm lazy :-) warns about applying it more than a few mm at a time due to curing/cracking issues, so packing it full of bog seemed a non-starter. By putting in a template as backing, I can use filler to deal with the problem.

174 posts

Master Geek
+1 received by user: 9


  Reply # 1968193 5-Mar-2018 10:38
Send private message

Would that bog work on Linna board too? took out the bulkhead lights and replaced with down lights in the soffit and need something that wont expand or contract. thanks

 

 


3238 posts

Uber Geek
+1 received by user: 847


  Reply # 1968232 5-Mar-2018 11:49
Send private message

oh for gawds sakes its 20mm, its the size of a $1 coin, 

 

Use expanding foam, (gorilla filler is perfect) then cut it back, seal and paint,

 

 


neb



668 posts

Ultimate Geek
+1 received by user: 114

Lifetime subscriber

  Reply # 1968244 5-Mar-2018 12:41
Send private message

Mavarick:

Would that bog work on Linna board too? took out the bulkhead lights and replaced with down lights in the soffit and need something that wont expand or contract. thanks

 

 

Could you post a photo of what you need to fill? If you need to fill a hole you've drilled for the power cable that's one thing, but packing bog around a light or light fitting isn't a good idea...

174 posts

Master Geek
+1 received by user: 9


  Reply # 1968252 5-Mar-2018 12:52
Send private message

neb:
Mavarick:

 

Would that bog work on Linna board too? took out the bulkhead lights and replaced with down lights in the soffit and need something that wont expand or contract. thanks

Could you post a photo of what you need to fill? If you need to fill a hole you've drilled for the power cable that's one thing, but packing bog around a light or light fitting isn't a good idea...

 

I'll get a photo up later,  the cable has been removed from the wall , no longer any fitting or wires there, I did call the Hardies helpline, but if its over the size of the nail or screw hole they dont recommend anything, there way of getting out of any water issuses I suppose.


174 posts

Master Geek
+1 received by user: 9


  Reply # 1968518 5-Mar-2018 21:25
Send private message

Click to see full size

 

 


neb



668 posts

Ultimate Geek
+1 received by user: 114

Lifetime subscriber

  Reply # 1970144 6-Mar-2018 20:21
Send private message

wellygary:

oh for gawds sakes its 20mm, its the size of a $1 coin, 

 

 

The reason I'm asking is that in other posts I've complained endlessly about the cowboy work done on this place by previous owners (latest gem: Was working under the eaves and looked down at the flashing over the kitchen window, they'd packed freakin' polyfilla (or at least one of the chalk/gypsum fillers) into the gap between the top of the fibrolite and the flashing, which was now a crumbling line of flaky, chalky gunk with a mm or two of gap on each side). So before I end up as the next owner's cowboy, I wanted to get advice on how to do it properly. The template trick worked fine.

neb



668 posts

Ultimate Geek
+1 received by user: 114

Lifetime subscriber

  Reply # 1970148 6-Mar-2018 20:27
Send private message

Mavarick:

Click to see full size

 

 

 

 

That's pretty tiny, I'd use an acrylic-based filler, Bunnings has one for just under $4 so you don't feel so bad about throwing away 90% of the tube when it hardens. It's sandable, paintable (unlike a lot of silicone sealers), and pretty durable, I've been using it to stop up various gaps in exterior walls.

 1 | 2
Filter this topic showing only the reply marked as answer View this topic in a long page with up to 500 replies per page Create new topic

Twitter »

Follow us to receive Twitter updates when new discussions are posted in our forums:



Follow us to receive Twitter updates when news items and blogs are posted in our frontpage:



Follow us to receive Twitter updates when tech item prices are listed in our price comparison site:





News »

Intel introduces new NUC kits and NUC mini PCs
Posted 16-Aug-2018 11:03


The Warehouse leaps into the AI future with Google
Posted 15-Aug-2018 17:56


Targus set sights on enterprise and consumer growth in New Zealand
Posted 13-Aug-2018 13:47


Huawei to distribute nova 3i in New Zealand
Posted 9-Aug-2018 16:23


Home robot Vector to be available in New Zealand stores
Posted 9-Aug-2018 14:47


Panasonic announces new 2018 OLED TV line up
Posted 7-Aug-2018 16:38


Kordia completes first live 4K TV broadcast
Posted 1-Aug-2018 13:00


Schools get safer and smarter internet with Managed Network Upgrade
Posted 30-Jul-2018 20:01


DNC wants a safer .nz in the coming year
Posted 26-Jul-2018 16:08


Auldhouse becomes an AWS Authorised Training Delivery Partner in New Zealand
Posted 26-Jul-2018 15:55


Rakuten Kobo launches Kobo Clara HD entry level reader
Posted 26-Jul-2018 15:44


Kiwi team reaches semi-finals at the Microsoft Imagine Cup
Posted 26-Jul-2018 15:38


KidsCan App to Help Kiwi Children in Need
Posted 26-Jul-2018 15:32


FUJIFILM announces new high-performance lenses
Posted 24-Jul-2018 14:57


New FUJIFILM XF10 introduces square mode for Instagram sharing
Posted 24-Jul-2018 14:44



Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.

Alternatively, you can receive a daily email with Geekzone updates.