Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.


5 posts

Wannabe Geek
+1 received by user: 1


Topic # 190811 13-Jan-2016 12:51
One person supports this post
Send private message

I've just got connected to a BigPipe fibre/UFB setup using a Netcomm NF4V.

As I couldn't find a clear, easy post I thought I'd put this here as it worked for me first time and will hopefully help someone.

Thank you and credit to Felix@Bigpipe for providing the following instructions:laughing

 

To set up your router for UFB, follow the steps below:

 

Before you start, restore your router to factory defaults, either by holding the small reset button on the back for 30 seconds, or through the Management, Settings menu. 

1. Connect your computer to a LAN port on the router Connect the WAN port on the router to the GE1 port on the ONT
2. Log in to the router at http://192.168.20.1 The default username and password are admin/admin
3. On the left panel click Advanced Setup, and then click WAN Service.
4. Tick the remove button on the preconfigured service, and then click the Remove button.
5. Click Layer 2 on the left pane, then click on ETH interface.
6. Tick the remove box, and then click the Remove button.
7. Click the Add button.
8. Select eth4/eth4, and click Apply/Save.
9. Click WAN service on the left panel.
10. Click the Add button.
11. Select eth4/eth4 from the drop down menu, and then click the Next button.
12. Select PPP over Ethernet (PPPoE)
13. Leave the service description at its default.
14. Set 802.1P Priority to -1 and the 802.1Q VLAN ID to -1. Click Next.
15. Enter PPP Username as Bigpipe, and PPP Password as Bigpipe.
16. Set the MTU to 1492
17. Ensure that “Enable IPv4 for this service” is ticked.
18. Click the Next button.
19. Ensure that ppp0.1 is in the left column, and click the Next button.
20. Again ensure that ppp0.1 is in the left column, and click the Next button.
21. Click the Apply/Save button.
22. Click Management from the left column, and then Reboot.
23. Click the Reboot button.
24. Your router will reboot, and after it has turned back on you should be able to connect to the internet.

Good luck, hope this post makes it easier for someone!

 

And if you're still having trouble contact support@bigpipe.co.nz letting them know the status of the lights on the ONT:

 

Power: Red/Green/Off

 

Optical: Red/Green/Off

 

Alarm: Red/Green/Off

 

LAN: Orange/Green/Off

 

Update: Red/Green/Off

Filter this topic showing only the reply marked as answer Create new topic
2623 posts

Uber Geek
+1 received by user: 501


  Reply # 1470141 13-Jan-2016 16:04
Send private message

What is the WiFi range like on this router?

I am hopefully getting closer to getting ufb installed via bigpipe, and am looking at keeping the old landline number and porting that to 2talk. I could buy a separate voip gizmo's, but that's another box and power plug. The only thing that puts me off is the single WiFi band. But possibly 5GHz is not that useful between rooms/floors anyway.




Nothing is impossible for the man who doesn't have to do it himself - A. H. Weiler



5 posts

Wannabe Geek
+1 received by user: 1


  Reply # 1484520 3-Feb-2016 16:03
Send private message

The router is a bit quirky in terms of it's interface and set-up (kind of like the older Drayteks) but it's feature rich, and rock solid once you get it configured.

 

My house is on two floors and I have had no problems with WiFi between rooms where ever I am in the house - late 1960s, villa.

 

I also ported my number to 2Talk (from XNet/WorldXChange) and haven't looked back. 2Talk is great in terms of functionality, price and more importantly service and call quality. I often had problems calling Argentina in particular with Xnet and if I tried SkypeOut with the same equipment it would work fine. This also prompted me to change from XNet and this issues are a thing of the past.

 

For the price point, I'd have no problems recommending this particular set-up if you can live with the quirks of the router interface.


122 posts

Master Geek
+1 received by user: 98

Trusted
BigPipe

  Reply # 1484531 3-Feb-2016 16:11
One person supports this post
Send private message

sjoseph: I've just got connected to a BigPipe fibre/UFB setup using a Netcomm NF4V.

As I couldn't find a clear, easy post I thought I'd put this here as it worked for me first time and will hopefully help someone.

 

 

Good call, thanks for this post. Coincidentally, we've actually just put a bunch of Bigpipe modem guides on our site (just put one up for the NF4V for fibre as well!), and we're going to be adding more as often as we can. 

Love to hear what you think!





www.bigpipe.co.nz

 

https://www.facebook.com/BigPipeNZ

 

https://twitter.com/BigPipeNZ

 




5 posts

Wannabe Geek
+1 received by user: 1


  Reply # 1494730 18-Feb-2016 11:03
Send private message

I love the new router guides, they're clear and concise and it saves me having to spend my time configuring the routers for friends and family tongue-out

 

NOTE: at the time I'm writing this post BigPipe are updating their pages so if you can't find your router listed in the new location: https://www.bigpipe.co.nz/modem-guides

 

Try this link for the original guides wink http://pages.bigpipe.co.nz/modem-router-setup-guides/

 

 


Filter this topic showing only the reply marked as answer Create new topic

Twitter »

Follow us to receive Twitter updates when new discussions are posted in our forums:



Follow us to receive Twitter updates when news items and blogs are posted in our frontpage:



Follow us to receive Twitter updates when tech item prices are listed in our price comparison site:





News »

N4L helping TAKA Trust bridge the digital divide for Lower Hutt students
Posted 18-Jun-2018 13:08


Winners Announced for 2018 CIO Awards
Posted 18-Jun-2018 13:03


Logitech Rally sets new standard for USB-connected video conference cameras
Posted 18-Jun-2018 09:27


Russell Stanners steps down as Vodafone NZ CEO
Posted 12-Jun-2018 09:13


Intergen recognised as 2018 Microsoft Country Partner of the Year for New Zealand
Posted 12-Jun-2018 08:00


Finalists Announced For Microsoft NZ Partner Awards
Posted 6-Jun-2018 15:12


Vocus Group and Vodafone announce joint venture to accelerate fibre innovation
Posted 5-Jun-2018 10:52


Kogan.com to launch Kogan Mobile in New Zealand
Posted 4-Jun-2018 14:34


Enable doubles fibre broadband speeds for its most popular wholesale service in Christchurch
Posted 2-Jun-2018 20:07


All or Nothing: New Zealand All Blacks arrives on Amazon Prime Video
Posted 2-Jun-2018 16:21


Innovation Grant, High Tech Awards and new USA office for Kiwi tech company SwipedOn
Posted 1-Jun-2018 20:54


Commerce Commission warns Apple for misleading consumers about their rights
Posted 30-May-2018 13:15


IBM leads Call for Code to use cloud, data, AI, blockchain for natural disaster relief
Posted 25-May-2018 14:12


New FUJIFILM X-T100 aims to do better job than smartphones
Posted 24-May-2018 20:17


Stuff takes 100% ownership of Stuff Fibre
Posted 24-May-2018 19:41



Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.

Alternatively, you can receive a daily email with Geekzone updates.