Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.




6 posts

Wannabe Geek


Topic # 179327 4-Sep-2015 10:26
Send private message

i drive a mazda 3 
ive had my front right 19 inch tyre replaced a month ago,
ever since it seems like there is some vibration whilst driving from 50-80kms,
i have had the tyres balanced and its fine
i was reading in some threads this could be caused by fault engine mounts?
any one have this type of problem?

Create new topic
251 posts

Ultimate Geek
+1 received by user: 110


  Reply # 1379580 4-Sep-2015 10:32
Send private message

Did you have the alignment checked at the same time?

Probably too soon to tell, but a big hint is if the tyres are not wearing evenly.  If the wear is not even then the alignment is probably out.


The other possibility I guess is if the tyres are not inflated correctly.  Have you checked all four tyres?


ps. I'm not inclined to think it is engine mounts if it only started happening *after* the tyre was changed.  That would be a too big of a coincidence.  So I think it will be related to this change.




Try my latest project, a Cisco type 5 enable secret password cracker written in javascript!

520 posts

Ultimate Geek
+1 received by user: 193

Subscriber

  Reply # 1379582 4-Sep-2015 10:37
Send private message

Need more info.
If it suddenly appeared at the time of your tire replacement it's likely associated.

Why did you have the RH tire replaced? Unusual wear? Hit a curb?
Have you checked it's mounted securely against the hub? Not a chunk of rust/dirt jammed in there..?
New, grippy tread will make a wheel alignment problem or warped rotor more obvious.

 
 
 
 


Banana?
3860 posts

Uber Geek
+1 received by user: 765

Subscriber

  Reply # 1379596 4-Sep-2015 10:45
Send private message

Have the new Tyre (FR) and the existing FL tyre got the same tread pattern? Is the FL quite new or have good tread depth?

19's are pretty big for a Mazda3. I have 18s on mine and wondered what 19s would look like.

4169 posts

Uber Geek
+1 received by user: 1816


  Reply # 1379609 4-Sep-2015 11:02
Send private message

Mis-alignment alone shouldn't cause vibration.  Mis-alignment combined with another issue (worn suspension bushes etc) might.
I suspect a balance issue.  Are they aftermarket mags, are they centred on the hub correctly, is there rust or something stopping them from sitting flush on the hub, have they got the correct wheel nuts to suit the mags, and have they been torqued correctly or has some ape with a rattle gun over-tightened them and/or not tightened them diagonally?
(correct torque for the very lightweight mags on one of my cars is only about 75 ft/lb - 100nm - even my battery rattle gun is well over 500 ft/lb - very useful for removing wheel nuts, but great care needed if used to tighten them - even with steel rims).  Yes tyre shop guys use them all the time with varying degree of skill.  After being at a tyre shop, I take the car home, loosen and retorque the nuts.

16331 posts

Uber Geek
+1 received by user: 1895

Trusted

  Reply # 1379618 4-Sep-2015 11:21
Send private message

When this happened to me the steering ball joint thingy that connects something to something under the car was worn on that side.

But with mine case, that one tyre would wear out within 5000ks, took them 3 tyres later before I got suspicious and challenged them something's not right how can you keep selling my a tyre and it's gone after a few months

251 posts

Ultimate Geek
+1 received by user: 110


  Reply # 1379632 4-Sep-2015 11:56
Send private message

After thought going through my mind which is growing on me - did you by chance have only the new wheel balanced?

If so, and the balance of the other front wheel was wrong (say because the tyre is now half worn from when it was originally balanced) they you could get the issue you are describing.  I would consider getting all four wheels balanced to make sure.




Try my latest project, a Cisco type 5 enable secret password cracker written in javascript!

251 posts

Ultimate Geek
+1 received by user: 110


  Reply # 1379638 4-Sep-2015 11:57
Send private message

Another thought again - has perhaps one of the new (or old) balancing weights come off?  Check the rim to see if there are any clean/shiny spots that might indicate where a weight once was - and is no longer.




Try my latest project, a Cisco type 5 enable secret password cracker written in javascript!

Fully Operational
3267 posts

Uber Geek
+1 received by user: 1063

Trusted
Vocus
Subscriber

  Reply # 1379662 4-Sep-2015 12:24
One person supports this post
Send private message

Take it to a mechanic and get them to look over the suspension and steering bushes.  If none of those are bad then go back to the tyre shop and have them check the tyre and possibly re balance the wheel.

Create new topic



Twitter »

Follow us to receive Twitter updates when new discussions are posted in our forums:



Follow us to receive Twitter updates when news items and blogs are posted in our frontpage:



Follow us to receive Twitter updates when tech item prices are listed in our price comparison site:





News »

Red Hat unveils production-ready open source hyperconverged infrastructure
Posted 23-Jun-2017 22:10


Whatever ailed Vodafone broadband … seems to be fixed
Posted 23-Jun-2017 14:10


VMware NSX Meets Stringent Government Security Standards with Common Criteria Certification
Posted 22-Jun-2017 19:05


Brother launches next-generation colour laser printers and all-in- ones for business
Posted 22-Jun-2017 18:56


Intel and IOC announce partnership
Posted 22-Jun-2017 18:50


Samsung Galaxy Tab S3: Best Android tablet
Posted 21-Jun-2017 12:05


Wellington-based company helping secure Microsoft browsers
Posted 20-Jun-2017 20:51


Endace delivers high performance with new 1/10/40 Gbps packet capture card
Posted 20-Jun-2017 20:50


You can now integrate SMX security into Microsoft Office 365, Google and other cloud email platforms
Posted 20-Jun-2017 20:47


Ravensdown launches new decision-making tool HawkEye
Posted 19-Jun-2017 15:38


Spark planning to take on direct management of all consumer stores
Posted 19-Jun-2017 10:03


Qrious acquires Ubiquity
Posted 14-Jun-2017 12:21


Spark New Zealand prepares for 5G with Nokia
Posted 14-Jun-2017 12:16


The future-proof 10.5-inch iPad Pro
Posted 13-Jun-2017 18:16


Mandatory data breach reporting in Australia
Posted 13-Jun-2017 11:30



Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.

Alternatively, you can receive a daily email with Geekzone updates.