Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.




35 posts

Geek
+1 received by user: 11


Topic # 226182 24-Dec-2017 11:42
Send private message quote this post

I've just bought a set of Pro Rack roof racks for my 2005 Mazda Premacy. This doesn't have gutters, and so it uses a single screw mounting point for each mount, under some rails on the roof.

 

 

This is a grub screw with a hex bolt at the top.

 

The rest of the mount goes together like this:

 


and

Three out of four of them looked like this,

 

 

and worked fine, but the last one looks like this:

 

 

It looks like water has got in there, and the whole thread is rusted away. I tried putting the bolt in hoping that there would be good metal underneath some surface rust, but the whole thing looks rotten. As far as I can tell, there is not enough good metal remaining to even tap a larger hole.

 

My question is:- does anyone have any ideas as to how I could get the grub screw (or a similar thread screw) mounted securely where the rusted hole was? A friend suggested filling it full of epoxy, but I am not confident in the integrity of the metal around the hole. I thought a bolt with a largish head from the inside of the car would be an option (after taking out the roof lining), with tons of silicon or other waterproofing type stuff. (And yes, I know there will be a general rust problem under that rail...)

 

Does anyone have any brilliant ideas?

 

 


Create new topic
10313 posts

Uber Geek
+1 received by user: 3178

Trusted
Lifetime subscriber

  Reply # 1924784 25-Dec-2017 00:32
Send private message quote this post

So, is that an old bolt which as sheared off and been left in the hole?






2281 posts

Uber Geek
+1 received by user: 229


  Reply # 1924810 25-Dec-2017 06:54
One person supports this post
Send private message quote this post

That's what it looks like. Similar roof mounts use Rivnuts but the nut on the Mazda seems inserted from below.





 
 
 
 


524 posts

Ultimate Geek
+1 received by user: 40


  Reply # 1924829 25-Dec-2017 08:24
Send private message quote this post

Could you get one of the other style mounts and use that instead?
They have a steel belt that wraps around the top of the door frame at the roof, and when tightened with the roof bar they hold tight.

Hmm, what to write...
962 posts

Ultimate Geek
+1 received by user: 479

Trusted
Lifetime subscriber

  Reply # 1924848 25-Dec-2017 09:21
One person supports this post
Send private message quote this post

Use a large drill to remove remains of the old nut (avoiding the roof lining) and attach a new “nut plate” from below. It looks like a nut attached to a plate that has a couple of rivet holes.

Depending on your attachment method (you need to certain the rivets can’t pull out) you might be able to do it from above




Matthew




35 posts

Geek
+1 received by user: 11


  Reply # 1924854 25-Dec-2017 09:45
Send private message quote this post

Geektastic:

 

So, is that an old bolt which as sheared off and been left in the hole?

 

I'm pretty sure that is not the case - the mounting hole stands proud from the bottom of the gutter, as far as I can tell. The wall of the hole is corroded from both the inside and outside, and is thus very weak.

 

Loismustdye:

 

Could you get one of the other style mounts and use that instead?
They have a steel belt that wraps around the top of the door frame at the roof, and when tightened with the roof bar they hold tight.

 

I would have much preferred this type of arrangement, but the car (Premacy) has rear sliding doors, with nowhere that this type of thing can hook on to.

 

bung:

 

That's what it looks like. Similar roof mounts use Rivnuts but the nut on the Mazda seems inserted from below.


 

I'm not sure, and I haven't yet figured out how to remove the trim so that I can check :)

 

mdooher:

 

Use a large drill to remove remains of the old nut (avoiding the roof lining) and attach a new “nut plate” from below. It looks like a nut attached to a plate that has a couple of rivet holes.
Depending on your attachment method (you need to certain the rivets can’t pull out) you might be able to do it from above

 

This is the type of solution I suspect would be the best, as it would be strong. I'm rightfully concerned about kayaks flying off at highway speeds undecided. As long as I can ensure waterproofing, I'm happy to drill through the outer shell of the car itself if it will ensure strength (12 yr old car, I'm not worried too much about resale value).


2281 posts

Uber Geek
+1 received by user: 229


  Reply # 1924866 25-Dec-2017 09:59
Send private message quote this post

In the photo of the good "nut" the edge of the surrounding hole has a crisp edge that doesn't look as if it is in sheet metal. Is it the roof or a plastic spacer?



35 posts

Geek
+1 received by user: 11


  Reply # 1924867 25-Dec-2017 10:03
Send private message quote this post

Bung: In the photo of the good "nut" the edge of the surrounding hole has a crisp edge that doesn't look as if it is in sheet metal. Is it the roof or a plastic spacer?

 

A hard plastic spacer. I've levered up the edge of the trim that runs the length of the roof, and it looks like the plastic spacer is maybe 10 cm long.


54 posts

Master Geek
+1 received by user: 8


  Reply # 1924937 25-Dec-2017 11:57
Send private message quote this post

Will anything from here do?

https://www.ezlok.com

We use the spring type threaded inserts but it doesn't look like there is enough metal left to great into.

54 posts

Master Geek
+1 received by user: 8


  Reply # 1924938 25-Dec-2017 11:57
Send private message quote this post

Will anything from here do?

https://www.ezlok.com

We use the spring type threaded inserts but it doesn't look like there is enough metal left to thread into.



35 posts

Geek
+1 received by user: 11


  Reply # 1924952 25-Dec-2017 12:05
Send private message quote this post

JamjarsNZ: Will anything from here do?

https://www.ezlok.com

We use the spring type threaded inserts but it doesn't look like there is enough metal left to thread into.

 

Thanks for the link. I suspect that any solution will have to get rid of the existing Rivnut-type thing, as it is rusted beyond being rescuable...


2281 posts

Uber Geek
+1 received by user: 229


  Reply # 1924955 25-Dec-2017 12:20
Send private message quote this post

If the existing hole gets too mutilated to rescue Subaru use a system consisting of a threaded insert in a bracket bolted into rivnuts either side of the insert location. Whatever you come up with use high tensile bolts rather than something from the woodwork aisle.

Aussie
4114 posts

Uber Geek
+1 received by user: 1135

Trusted
Subscriber

  Reply # 1924957 25-Dec-2017 12:25
Send private message quote this post

Drill out and new riv-nut?

 

Places like https://www.fullyequipped.co.nz/locations/ that install canopies (and roof racks) should be able to do it for you really cheap.

 

 


1748 posts

Uber Geek
+1 received by user: 916


  Reply # 1924969 25-Dec-2017 13:12
Send private message quote this post

I don't think it's a rivnut, I think it's a threaded boss retained in a floating mount. I'm betting there is a little movement in the good one.

I'd:
Ask Mazda if they have replacements.
Ask a panelbeater or Mazda if they know how the gutter trim comes out (it's bound to be removable, and it's probably what holds the nuts in). Google might know too.

If you can achieve these two things, it'll probably be stupid simple to replace the lot.




Location: Dunedin



35 posts

Geek
+1 received by user: 11


  Reply # 1924998 25-Dec-2017 15:40
Send private message quote this post

andrewNZ: I don't think it's a rivnut, I think it's a threaded boss retained in a floating mount. I'm betting there is a little movement in the good one.

I'd:
Ask Mazda if they have replacements.
Ask a panelbeater or Mazda if they know how the gutter trim comes out (it's bound to be removable, and it's probably what holds the nuts in). Google might know too.

If you can achieve these two things, it'll probably be stupid simple to replace the lot.

 

Zero luck at searching on Google, until I remembered that the Premacy is sold as the Mazda 5 in the states, and then I found tons of images and guides. It looks like the offending piece is like this:

 

 

Definitely looks like I won't need to drill into the car body itself!


Create new topic



Twitter »

Follow us to receive Twitter updates when new discussions are posted in our forums:



Follow us to receive Twitter updates when news items and blogs are posted in our frontpage:



Follow us to receive Twitter updates when tech item prices are listed in our price comparison site:





News »

New Zealand hits peak broadband data
Posted 18-Jan-2018 12:21


Amazon Echo devices coming to New Zealand early February 2018
Posted 18-Jan-2018 10:53


$3.74 million for new electric vehicles in New Zealand
Posted 17-Jan-2018 11:27


Nova 2i: Value, not excitement from Huawei
Posted 17-Jan-2018 09:02


Less news in Facebook News Feed revamp
Posted 15-Jan-2018 13:15


Australian Government contract awarded to Datacom Connect
Posted 11-Jan-2018 08:37


Why New Zealand needs a chief technology officer
Posted 6-Jan-2018 13:59


Amazon release Silk Browser and Firefox for Fire TV
Posted 21-Dec-2017 13:42


New Chief Technology Officer role created
Posted 19-Dec-2017 22:18


All I want for Christmas is a new EV
Posted 19-Dec-2017 19:54


How clever is this: AI will create 2.3 million jobs by 2020
Posted 19-Dec-2017 19:52


NOW to deploy SD-WAN to regional councils
Posted 19-Dec-2017 19:46


Mobile market competition issues ComCom should watch
Posted 18-Dec-2017 10:52


New Zealand government to create digital advisory group
Posted 16-Dec-2017 08:47


Australia datum changes means whole country moving 1.8 metres north-east
Posted 16-Dec-2017 08:39



Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.

Alternatively, you can receive a daily email with Geekzone updates.