Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.




299 posts

Ultimate Geek
+1 received by user: 2


Topic # 85836 26-Jun-2011 12:53
Send private message

For ducting a dryer back to back with a wall - is it the sort of thing you *really* should get someone in for - or is it just a case of cutting through the gib + cladding and putting the plastic kit covers on each side before sticking the duct through?

I am probably a 3/10 in terms of DIY competency (though I do build my own PCs)




Q6600 @ 3.2Ghz (400x8) | GA-X38-DQ6 | 4Gb Corsair Dominator@800Mhz 4-4-4-12 | HIS HD5870 | Creative X-fi Fatality Pro | 2xWD SATAII Caviar Black 640Gb / 1xSeagate SATAII 7200.12 1000Gb | 2xASUS IDE DVDRW | Silverstone OP1000 PSU | Silverstone TJ09 Case

Create new topic
2260 posts

Uber Geek

Trusted

  Reply # 486030 26-Jun-2011 13:21
Send private message

Cut through the gib, then pull out any insulation in the way, cut through the cladding and you are done :)

No need to involve builders/contractors unless you think you'll mess it up

If you are screwing the outside duct vent into plasterboard, maybe get some better screws for it, because the screws which come with those kits will just fail if you have to remove it once




I have moved across the ditch.  Now residing in Melbourne as a VOIP/Video Technical Trainer/Engineer. 



299 posts

Ultimate Geek
+1 received by user: 2


  Reply # 486034 26-Jun-2011 13:27
Send private message

The outside cladding is 'shadowclad' - sort of a plywood thing.

What are the chances of a modern house having electrical wiring or gas pipes that low down on a wall - about a meter away from a door? This will be in a garage so there should be no insulation.




Q6600 @ 3.2Ghz (400x8) | GA-X38-DQ6 | 4Gb Corsair Dominator@800Mhz 4-4-4-12 | HIS HD5870 | Creative X-fi Fatality Pro | 2xWD SATAII Caviar Black 640Gb / 1xSeagate SATAII 7200.12 1000Gb | 2xASUS IDE DVDRW | Silverstone OP1000 PSU | Silverstone TJ09 Case

 
 
 
 


4084 posts

Uber Geek
+1 received by user: 1641

Trusted
Subscriber

  Reply # 486051 26-Jun-2011 13:45
Send private message

Usually you can get a good hint by way of plumbing or power points on the wall in line with where you want to cut.




iPad Air + iPhone SE + 2degrees 4tw!

These comments are my own and do not represent the opinions of 2degrees.


3064 posts

Uber Geek
+1 received by user: 438

Subscriber

  Reply # 486057 26-Jun-2011 14:13
Send private message

If you are worried about cutting something vital then just cut a smaller hole in the gib than you will finally require. If you set your knife to 10mm when you cut initially then you should only go through the gib. Then see what's behind it. You can patch the hole (which will be hidden by the dryer anyway) if you do find something that prevents you from putting the hole there. Just remember there are also galvanised steel braces set on an angle in some walls. They need to remain intact to ensure the structural integrity of your house.




Areas of Geek interest: Home Theatre, HTPC, Android Tablets & Phones, iProducts.

13349 posts

Uber Geek
+1 received by user: 2247

Trusted
Subscriber

  Reply # 486062 26-Jun-2011 14:25
Send private message

If you're only 3/10 then get someone in. You need to mount it on a stud, and seal the outside so it's watertight. It's an easy job for a competent handyman, perhaps get someone off builderscrack.co.nz (odd job and building auction site).




AWS Certified Solution Architect Professional, Sysop Administrator Associate, and Developer Associate
TOGAF certified enterprise architect
Professional photographer


3064 posts

Uber Geek
+1 received by user: 438

Subscriber

  Reply # 486070 26-Jun-2011 14:43
Send private message

timmmay: If you're only 3/10 then get someone in. You need to mount it on a stud, and seal the outside so it's watertight. It's an easy job for a competent handyman, perhaps get someone off builderscrack.co.nz (odd job and building auction site).


I assumed it was sitting on the floor.  If it is, and the vent is low on the outside wall it will need to be well weatherproofed or you will be asking for trouble as you won't get much protection from the eaves.




Areas of Geek interest: Home Theatre, HTPC, Android Tablets & Phones, iProducts.



299 posts

Ultimate Geek
+1 received by user: 2


  Reply # 486072 26-Jun-2011 14:45
Send private message

Dingbatt:
timmmay: If you're only 3/10 then get someone in. You need to mount it on a stud, and seal the outside so it's watertight. It's an easy job for a competent handyman, perhaps get someone off builderscrack.co.nz (odd job and building auction site).


I assumed it was sitting on the floor.  If it is, and the vent is low on the outside wall it will need to be well weatherproofed or you will be asking for trouble as you won't get much protection from the eaves.


Yeah it will be sitting on the ground. I have some silicone gel and an applicator gun (the type you slot the long cylindrical gel tube into) which I figured I could squirt around the outside of the external part of the vent




Q6600 @ 3.2Ghz (400x8) | GA-X38-DQ6 | 4Gb Corsair Dominator@800Mhz 4-4-4-12 | HIS HD5870 | Creative X-fi Fatality Pro | 2xWD SATAII Caviar Black 640Gb / 1xSeagate SATAII 7200.12 1000Gb | 2xASUS IDE DVDRW | Silverstone OP1000 PSU | Silverstone TJ09 Case



299 posts

Ultimate Geek
+1 received by user: 2


  Reply # 486077 26-Jun-2011 14:57
Send private message

timmmay: If you're only 3/10 then get someone in. You need to mount it on a stud, and seal the outside so it's watertight. It's an easy job for a competent handyman, perhaps get someone off builderscrack.co.nz (odd job and building auction site).


Yeah that is a fair point - I might have a close look at the area and like someone else has suggested maybe make a small, fixable hole to see what it looks like inside.

If there appears to be anything complicated I'll get someone in.

Edit:
Additionally the quality of online guides I've found is pretty low:
http://www.youtube.com/watch?v=DUxwySSMRzE

http://www.youtube.com/watch?v=o1LGpTu0mkU

http://construction.job.org.nz/do-you-need-to-know-about-installing-indoor-dryer-vent-read-here.html

I guess there are Insurance implications as well. If I did a crap job and water got in and damaged something I suspect my insurer wouldn't be jumping for joy. Might give them a quick call tomorrow first.






Q6600 @ 3.2Ghz (400x8) | GA-X38-DQ6 | 4Gb Corsair Dominator@800Mhz 4-4-4-12 | HIS HD5870 | Creative X-fi Fatality Pro | 2xWD SATAII Caviar Black 640Gb / 1xSeagate SATAII 7200.12 1000Gb | 2xASUS IDE DVDRW | Silverstone OP1000 PSU | Silverstone TJ09 Case

532 posts

Ultimate Geek
+1 received by user: 28


  Reply # 486230 26-Jun-2011 22:11
Send private message

casewindow:
I guess there are Insurance implications as well. If I did a crap job and water got in and damaged something I suspect my insurer wouldn't be jumping for joy. Might give them a quick call tomorrow first.


Might be you not leaping for joy Smile as these days water damage from building faults is often excluded or else wrapped in limiting terms in insurance policies.

In addition to the other suggestions, on the off chance you have to get an electrician in to get power to the drier he might install the duct for you?? 

Create new topic



Twitter »

Follow us to receive Twitter updates when new discussions are posted in our forums:



Follow us to receive Twitter updates when news items and blogs are posted in our frontpage:



Follow us to receive Twitter updates when tech item prices are listed in our price comparison site:





News »

New Zealand government to create digital advisory group
Posted 16-Dec-2017 08:47


Australia datum changes means whole country moving 1.8 metres north-east
Posted 16-Dec-2017 08:39


UAV Traffic Management Trial launching today in New Zealand
Posted 12-Dec-2017 16:06


UFB connections pass 460,000
Posted 11-Dec-2017 11:26


The Warehouse Group to adopt IBM Cloud to support digital transformation
Posted 11-Dec-2017 11:22


Dimension Data peeks into digital business 2018
Posted 11-Dec-2017 10:55


2018 Cyber Security Predictions
Posted 7-Dec-2017 14:55


Global Govtech Accelerator to drive public sector innovation in Wellington
Posted 7-Dec-2017 11:21


Stuff Pix media strategy a new direction
Posted 7-Dec-2017 09:37


Digital transformation is dead
Posted 7-Dec-2017 09:31


Fake news and cyber security
Posted 7-Dec-2017 09:27


Dimension Data New Zealand strengthens cybersecurity practice
Posted 5-Dec-2017 20:27


Epson NZ launches new Expression Premium Photo range
Posted 5-Dec-2017 20:26


Eventbrite and Twickets launch integration partnership in Australia and New Zealand
Posted 5-Dec-2017 20:23


New Fujifilm macro lens lands in New Zealand
Posted 5-Dec-2017 20:16



Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.

Alternatively, you can receive a daily email with Geekzone updates.