Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.




83 posts

Master Geek
+1 received by user: 20


Topic # 189188 19-Dec-2015 19:39
Send private message

Hi all,

I'm working with a house with structured wiring, cat 6 runs to various locations throughout the house, all terminating in a panel in the garage. The house has UFB, the ONT is installed in the panel in the garage, along with a network switch, and a telephone distribution board.

ISP is 2degrees, LFC is enable (so no VOIP via the ONT) - I've talked to 2d about this and we came to the conclusion that they can't think of a way to make it work how I want. However I'm wondering whether anyone else might have had some luck.

I want to have my router (a Fritz!Box) in a location on the other side of the house, that has two runs of Cat 6 between it and the garage panel. Right now, I've got analogue phone ports working around the house as well as wifi, with the following setup:

ONT LAN 1 patched to port connected to Fritz Box LAN 1
Telephone distribution board is patched to port connected to Fritz!Box FON 1 (ATA port)

However, I can't seem to get a config working that also allows me to use the Fritz!Box as my internet gateway and DHCP server for the wired network. I've tried the following:
ONT LAN 1 -> switch port 1 (garage), Fritz Box LAN 1 -> switch port 2, computer -> switch port 3, but it appears that in this configuration the Fritz!Box doesn't listen to any traffic.

Is there any way I can have all three functions working without running a third cable run (i.e. setup i'm running now, plus Fritz LAN 2 -> switch)? Can i use 100mbit and ATA on the same cable, two pairs each, leaving me a separate port for gigabit between Fritz LAN 2 and switch? Or is this going to cause me issues?

Thanks all!

Create new topic
4479 posts

Uber Geek
+1 received by user: 1289


  Reply # 1453647 19-Dec-2015 19:45
One person supports this post
Send private message

spronkey: Can i use 100mbit and ATA on the same cable, two pairs each, leaving me a separate port for gigabit between Fritz LAN 2 and switch? Or is this going to cause me issues?


This is the answer. You can get plug in splitters that use 2 pairs each, so would be limited to 100Mb/s if used for ethernet. As long as you only have 100/100 UFB, then use a 100Mb/s link from the ONT.

25683 posts

Uber Geek
+1 received by user: 5431

Moderator
Trusted
Biddle Corp
Subscriber

  Reply # 1453650 19-Dec-2015 19:57
One person supports this post
Send private message

Your solution is a splitter as mentioned above. If you want Gigabit your solution is hardware at each end to create some VLAN's across your network so the WAN and LAN can both be carried across a single cat6 run and the voice over the other.



 
 
 
 


20439 posts

Uber Geek
+1 received by user: 3901

Trusted
Subscriber

  Reply # 1453651 19-Dec-2015 20:04
2 people support this post
Send private message

Use dect built into the fritz and dont worry about distributing phone?




Richard rich.ms

3184 posts

Uber Geek
+1 received by user: 989

Subscriber

  Reply # 1453657 19-Dec-2015 20:44
Send private message

Couple of little Mikrotik's (or managed switch), some VLAN's and bob's your uncle.



83 posts

Master Geek
+1 received by user: 20


  Reply # 1453725 20-Dec-2015 01:17
Send private message

sbiddle: Your solution is a splitter as mentioned above. If you want Gigabit your solution is hardware at each end to create some VLAN's across your network so the WAN and LAN can both be carried across a single cat6 run and the voice over the other.


When you say gigabit - I assume you mean from ONT to router? Or would I need to split the data and leave a whole cable for analogue voice, leaving all data to and from the router as 100mbit?

richms: Use dect built into the fritz and dont worry about distributing phone?


Considered this, but already have some Uniden handsets that are annoyingly incompatible

212 posts

Master Geek
+1 received by user: 36


  Reply # 1453759 20-Dec-2015 08:38
One person supports this post
Send private message

What's the reason for having the fritzbox on the other side of the house?
Would another AP do the trick if it's for wifi as the patch panel, switches, ONT, phone distribution is in the garage?



83 posts

Master Geek
+1 received by user: 20


  Reply # 1453833 20-Dec-2015 11:29
Send private message

darkasdes2: What's the reason for having the fritzbox on the other side of the house?
Would another AP do the trick if it's for wifi as the patch panel, switches, ONT, phone distribution is in the garage?


I could use another AP yeah, but the Fritz Box in centre of house has coverage that is good enough, so was hoping to avoid the expense.

It also doesn't fit in the damn patch cabinet - the AVM routers are huge, and it's power supply is a stupid long tall shape!

13347 posts

Uber Geek
+1 received by user: 2247

Trusted
Subscriber

  Reply # 1453850 20-Dec-2015 12:01
Send private message

An extra AP is the simplest way. There are no doubt ways to achieve it, but you'll give up performance (maybe), add complexity, or add cost. An AP isn't expensive and may be worth the money for a simple network.




AWS Certified Solution Architect Professional, Sysop Administrator Associate, and Developer Associate
TOGAF certified enterprise architect
Professional photographer


Create new topic



Twitter »

Follow us to receive Twitter updates when new discussions are posted in our forums:



Follow us to receive Twitter updates when news items and blogs are posted in our frontpage:



Follow us to receive Twitter updates when tech item prices are listed in our price comparison site:





News »

UAV Traffic Management Trial launching today in New Zealand
Posted 12-Dec-2017 16:06


UFB connections pass 460,000
Posted 11-Dec-2017 11:26


The Warehouse Group to adopt IBM Cloud to support digital transformation
Posted 11-Dec-2017 11:22


Dimension Data peeks into digital business 2018
Posted 11-Dec-2017 10:55


2018 Cyber Security Predictions
Posted 7-Dec-2017 14:55


Global Govtech Accelerator to drive public sector innovation in Wellington
Posted 7-Dec-2017 11:21


Stuff Pix media strategy a new direction
Posted 7-Dec-2017 09:37


Digital transformation is dead
Posted 7-Dec-2017 09:31


Fake news and cyber security
Posted 7-Dec-2017 09:27


Dimension Data New Zealand strengthens cybersecurity practice
Posted 5-Dec-2017 20:27


Epson NZ launches new Expression Premium Photo range
Posted 5-Dec-2017 20:26


Eventbrite and Twickets launch integration partnership in Australia and New Zealand
Posted 5-Dec-2017 20:23


New Fujifilm macro lens lands in New Zealand
Posted 5-Dec-2017 20:16


Cyber security not being taken seriously enough
Posted 5-Dec-2017 20:13


Sony commences Android 8.0 Oreo rollout in New Zealand
Posted 5-Dec-2017 20:08



Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.

Alternatively, you can receive a daily email with Geekzone updates.