Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.




15236 posts

Uber Geek


# 220374 8-Aug-2017 13:53
Send private message

Doing a new build in a fibre area. I have a couple of questions

 

The land is totally clear. As there is no existing copper line installed on the site, who pays for the fibre to be laid within the property,. With existing houses it is currently free. However according to this page ,it is the land owner who is responsible for paying for everything, although I don't know if that applies in areas where the install is supposed to be free https://www.chorus.co.nz/help-and-support/wiring-broadband/who-will-install-wiring-fibre-broadband-if-im-building-new-house 

 

 

 

Also is it possible to not have an external pipe and ETP running up the side of external cladding?  Normally services go into a building through the slab when building new, and not piped on teh outside. Instead can a conduit be installed in the slab, and an ETP box be installed in the wardrobe, where networking gear will be located. Or is an ETP box required at all in that case, and can it just be connected straight to the ONT? Can the contractor just lay a conduit down through the slab where the exterior wall will go, with the required diameter and curve radius, to the outside. Which will then allow the chorus installers to pull the wire up through. Potentially it would make the install a lot easier for them, and reduces the risk of weather tightness issues with cladding. If this is possible, is there any info on the exact specs this needs to meet? I can't see much on the chorus website about this.

 

 

 

TIA


Filter this topic showing only the reply marked as answer View this topic in a long page with up to 500 replies per page Create new topic
 1 | 2
8917 posts

Uber Geek

Lifetime subscriber

  # 1841139 8-Aug-2017 13:56
Send private message

interested as well but we already have a copper conenction


936 posts

Ultimate Geek


  # 1841182 8-Aug-2017 14:40
One person supports this post
Send private message

I'm also interested in hearing responses to this, will be in a similar position next year. Couldn't find much info about new builds on the chorus website.

 

 


 
 
 
 




15236 posts

Uber Geek


  # 1841227 8-Aug-2017 15:35
Send private message

I did phone chorus about it, but I don't think the person I spoke to understood., and I was probably only dealing with a call centre where they are just using a database of FAQs. They said that it always had to go on the outside of the house, so that the ETP could be accessed. I suspect that is the easiest way to do it in terms of a uniform 'one size fits all approach'. But the fact is that all other services usually go in the slab or wall on a new build. Even the old copper lines go up through the slab in the walls. My cladding manufacturer did say that if it goes on the outside, they wouldn't cover any leaks caused by it. 




15236 posts

Uber Geek


  # 1841229 8-Aug-2017 15:37
Send private message

CutCutCut:

 

I'm also interested in hearing responses to this, will be in a similar position next year. Couldn't find much info about new builds on the chorus website.

 

 

 

 

 

 

It does seem to be lacking a lot of info. I suspect most standard houses being built by developers, will just get it installed on the outside, beucase it is the easiest default option. 


681 posts

Ultimate Geek

Lifetime subscriber

  # 1841230 8-Aug-2017 15:40
Send private message

Isn't the whole point of an ETP is that it is an EXTERNAL Termination Point?




15236 posts

Uber Geek


  # 1841233 8-Aug-2017 15:47
Send private message

msukiwi:

 

Isn't the whole point of an ETP is that it is an EXTERNAL Termination Point?

 

 

 

 

Doesn't mean that it has to go on the external wall the building though, it could be an external termination box on an interior wall.From my understanding based on my current install, is that it is just a cover that can be accessed for the connection of the main line with the house line. Also I can see the point of having an ETP if the install is going on the exterior of the building, as that then connects to the ONT. However if the fibre is already inside the building envelope, it could then connect to the ONT directly. I am just wondering if it has more to do with the ownership of the fibre itself, as usually the owner will own all cables and pipes that are on their property. But that may not be the case with fibre on your property.  I have heard of fibre being installed in the wall,by others by can't find any info on the requirements.


I fix stuff!
1786 posts

Uber Geek

Trusted
Vocus
Subscriber

  # 1841235 8-Aug-2017 15:48
One person supports this post
Send private message

ETP is required to take the hardened fibre cable and turn it into internal fibre cable. The ETP is always required and is required to be on the outside (External Termination Point). 


 
 
 
 


'That VDSL Cat'
11211 posts

Uber Geek

Trusted
Spark
Subscriber

  # 1841242 8-Aug-2017 15:55
Send private message

Sounddude:

 

ETP is required to take the hardened fibre cable and turn it into internal fibre cable. The ETP is always required and is required to be on the outside (External Termination Point). 

 

 

 

 

as above, it is a termination point intended to be external.

 

Chorus do cover the connection up to the ONT as that is where their network ends (assuming you have not caused damage to the equipment - eg ripped the ONT off the wall and broke the fibre)





#include <std_disclaimer>

 

Any comments made are personal opinion and do not reflect directly on the position my current or past employers may have.




15236 posts

Uber Geek


  # 1841250 8-Aug-2017 15:59
Send private message

hio77:

 

Sounddude:

 

ETP is required to take the hardened fibre cable and turn it into internal fibre cable. The ETP is always required and is required to be on the outside (External Termination Point). 

 

 

 

 

as above, it is a termination point intended to be external.

 

Chorus do cover the connection up to the ONT as that is where their network ends (assuming you have not caused damage to the equipment - eg ripped the ONT off the wall and broke the fibre)

 

 

 

 

Thanks for that info. Is there a limit to the distance between the ONT and the ETP? Just that I had planned to have them in the same location, but will have to now put it in a service area on the corner of the building which is quite a distance from the ONT location.


8917 posts

Uber Geek

Lifetime subscriber

  # 1841261 8-Aug-2017 16:14
Send private message

if you run the ducting and make it as easy as possible to get the hybrid fibre cable (fibre with some copper pairs in it) from the ETP to the ONT i dont think there is much issue.

 

and ETP inside a building ceases to be an ETP, as the E is for External


3416 posts

Uber Geek


  # 1841272 8-Aug-2017 16:27
One person supports this post
Send private message

Your key information can be found on enables site.

 

https://www.enable.net.nz/connect-to-fibre/connecting-your-home/preparing-your-home/

 

 

 

In particular the specifications for the bends and such. Their feel is the sparky should know. But if you are attempting to DIY, the specifications are laid out there.




15236 posts

Uber Geek


  # 1841277 8-Aug-2017 16:29
Send private message

Thanks, that was the document I was looking for.


521 posts

Ultimate Geek

Lifetime subscriber

  # 1841309 8-Aug-2017 16:57
One person supports this post
Send private message

FWIW, my fibre install has no ETP. But, it's an old house and an aerial install, so not really applicable to the circumstances here.

The "exterior" fibre runs all the way from the pole to the ONT. Seems to work as normal, but I suspect it's not in line with the standard installation requirements.

4968 posts

Uber Geek

Trusted

  # 1841314 8-Aug-2017 17:06
Send private message

mattwnz: My cladding manufacturer did say that if it goes on the outside, they wouldn't cover any leaks caused by it. 

 

 

What about any other items that penetrate the cladding such as external taps, power meter boxes?


832 posts

Ultimate Geek


  # 1841325 8-Aug-2017 17:32
Send private message

Yes the ETP - Goes externally on the side of the build - it is the point at which the fibre, wether it be blown or a fixed fibre is transitioned into a suitable internal cable or microducting.  It is also the point at which your service can be checked, by the service company, without requiring the end customer to be home to allow access (the same way that your power/gas meter - Switch, Fuse or tap etc is externally accessed)

 

Normally with a greenfeilds install (New House/sub-division/never had copper) a conduit with a draw wire, or just an empty microduct, is installed to the outside during the building developement (hopefully lined up with the internal pathway/drawwire) and when service is requested, at a later stage, then the end of the conduit/microduct is fitted off with the ETP (all so known as an FTB - Fibre Termination Box) and the actual fibre is blown/ hauled through into it. Internal cable/ ducting is installed at this stage too

 

 


 1 | 2
Filter this topic showing only the reply marked as answer View this topic in a long page with up to 500 replies per page Create new topic



Switch your broadband provider now - compare prices


Twitter and LinkedIn »



Follow us to receive Twitter updates when new discussions are posted in our forums:



Follow us to receive Twitter updates when news items and blogs are posted in our frontpage:



Follow us to receive Twitter updates when tech item prices are listed in our price comparison site:





News »

Microsoft Translator understands te reo Māori
Posted 22-Nov-2019 08:46


Chorus to launch Hyperfibre service
Posted 18-Nov-2019 15:00


Microsoft launches first Experience Center worldwide for Asia Pacific in Singapore
Posted 13-Nov-2019 13:08


Disney+ comes to LG Smart TVs
Posted 13-Nov-2019 12:55


Spark launches new wireless broadband "Unplan Metro"
Posted 11-Nov-2019 08:19


Malwarebytes overhauls flagship product with new UI, faster engine and lighter footprint
Posted 6-Nov-2019 11:48


CarbonClick launches into Digital Marketplaces
Posted 6-Nov-2019 11:42


Kordia offers Microsoft Azure Peering Service
Posted 6-Nov-2019 11:41


Spark 5G live on Auckland Harbour for Emirates Team New Zealand
Posted 4-Nov-2019 17:30


BNZ and Vodafone partner to boost NZ Tech for SME
Posted 31-Oct-2019 17:14


Nokia 7.2 available in New Zealand
Posted 31-Oct-2019 16:24


2talk launches Microsoft Teams Direct Routing product
Posted 29-Oct-2019 10:35


New Breast Cancer Foundation app puts power in Kiwi women's hands
Posted 25-Oct-2019 16:13


OPPO Reno2 Series lands, alongside hybrid noise-cancelling Wireless Headphones
Posted 24-Oct-2019 15:32


Waikato Data Scientists awarded $13 million from the Government
Posted 24-Oct-2019 15:27



Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.


Support Geekzone »

Our community of supporters help make Geekzone possible. Click the button below to join them.

Support Geezone on PressPatron



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.

Alternatively, you can receive a daily email with Geekzone updates.