Chorus VDSL - Vectoring & G.INP rolling in

Forums › New Zealand Broadband › Chorus VDSL - Vectoring & G.INP rolling in

1 | ... | 15 | 16 | 17 | 18 | 19 | 20 | 21 | 22 | 23 | 24 | 25 | ... | 27

374 posts

Ultimate Geek

Trusted

Chorus

Lifetime subscriber

#2021111 23-May-2018 12:51

wratterus:

MU_U as well as KIT_G would have been one of those that failed too?

MU_U was successful last night - all looks OK.
Neither KTI_G doesnt have the vectoring capable cards in it, so is not part of the current rollout.

Lenovo

Lenovo computer and accessories deals (affiliate link).

wratterus

1687 posts

Uber Geek

#2021112 23-May-2018 12:54

BMarquis:

wratterus:

MU_U as well as KIT_G would have been one of those that failed too?

MU_U was successful last night - all looks OK.
Neither KTI_G doesnt have the vectoring capable cards in it, so is not part of the current rollout.

Thank you - I have a DV130 on MU_U which I don't see any changes on - it is running M4 firmware rather than M8, but does state 'vectoring support'.

Has anyone got a DV130 with Vectoring enabled yet to confirm if it does display the 'vectoring active' on the dashboard screen like the 2760 etc does?

KIT_G, not KTI_G sorry

djchcane

5 posts

Wannabe Geek

#2021114 23-May-2018 12:56

BMarquis:

djchcane:

Have been reading this thread with interest; and note that my local cabinet SPE_G was supposed to gain Vectoring last night between 2300-0600L.

Whilst I cannot tell specifically weter this has happened i did witness changes to my profile overnight - moved from 8B to 17A. Is this an expected change when vectoring is enabled?

I run a Draytek DV130 as indicated in the pre and post screenshots below.

Pre Vectoring:

--snipped image

Post Vectoring:

--snipped image

Sync really hasnt changed much - upstream maybe a little boost - but I had hoped for more!

Cheers,

Dave

Apologies, something was not quite right with this DSLAM. Please check again now.

Thanks BMarquis - I have just run a remote speedtest - and that didnt demonstrate any improvement - will check the CLI when I get in later. Should a reboot be necessary - or leave alone?

BMarquis

374 posts

Ultimate Geek

Trusted

Chorus

Lifetime subscriber

#2021124 23-May-2018 13:08

djchcane:

Thanks BMarquis - I have just run a remote speedtest - and that didnt demonstrate any improvement - will check the CLI when I get in later. Should a reboot be necessary - or leave alone?

No need to reboot.
Note that vectoring will only give you an improvement where your line is impacted by crosstalk. SPE_G has a relatively low number of VDSL services, so in your case the benefit will be longer term - you wont get as much of a reduction in sync rate as users move from ADSL to VDSL on that cabinet.

Happy to see what our network thinks of your line - just PM me your address.

BMarquis

374 posts

Ultimate Geek

Trusted

Chorus

Lifetime subscriber

#2021125 23-May-2018 13:09

wratterus:

Thank you - I have a DV130 on MU_U which I don't see any changes on - it is running M4 firmware rather than M8, but does state 'vectoring support'.

Has anyone got a DV130 with Vectoring enabled yet to confirm if it does display the 'vectoring active' on the dashboard screen like the 2760 etc does?

KIT_G, not KTI_G sorry

yeah sorry, we both had typos with that cabinet name :)
If you PM me the address, I can check to see what our network thinks is going on.

freakngeek

356 posts

Ultimate Geek

#2021128 23-May-2018 13:11

Here is example of DV2860 with 'Vectoring Active' from @coffeebaron
Am hoping DV130's will also light up with Green lettering

Dairyxox

1591 posts

Uber Geek

#2021132 23-May-2018 13:18

I've got vectoring on here now.

Download speed has dropped by about 15% (24Mbps to 21Mbps)

Upload speed has increased by about 10% (1.36Mbps to 1.49Mbps)

This suits me fine, as I'm really wanting more upload bandwidth.

BMarquis

374 posts

Ultimate Geek

Trusted

Chorus

Lifetime subscriber

#2021139 23-May-2018 13:21

Dairyxox:

I've got vectoring on here now.

Download speed has dropped by about 15% (24Mbps to 21Mbps)

Upload speed has increased by about 10% (1.36Mbps to 1.49Mbps)

This suits me fine, as I'm really wanting more upload bandwidth.

We see approx 15% variance on a given line whenever they resync.
Based on the sync rates, I'd say vectoring is not helping you at all, and the change in sync rates is just normal variation.

Dairyxox

1591 posts

Uber Geek

#2021145 23-May-2018 13:33

Could be, I've been monitoring it, and will continue to do so.

I'll let you know if anything noteworthy happens.

hio77

'That VDSL Cat'
12984 posts

Uber Geek

ID Verified

Trusted

Voyager

Subscriber

#2021151 23-May-2018 13:45

Dairyxox:

I've got vectoring on here now.

Download speed has dropped by about 15% (24Mbps to 21Mbps)

Upload speed has increased by about 10% (1.36Mbps to 1.49Mbps)

This suits me fine, as I'm really wanting more upload bandwidth.

as brent said, this is within the margin of error to be honest.

would not surprise me if the dip you have seen is a move from 8b to 17a.

#include <std_disclaimer>

Any comments made are personal opinion and do not reflect directly on the position my current or past employers may have.

timmay556

98 posts

Master Geek
Inactive user

#2021179 23-May-2018 14:53

Hey guys, I see that my exhange is booked in for today ( I even saw a chorus van parked outside the box on my way to work this morning) is the change over immediate or does the effect take a few days?

MichaelNZ

1227 posts

Uber Geek

Trusted

Integrity Tech Solutions

#2021183 23-May-2018 14:55

timmay556: Hey guys, I see that my exhange is booked in for today ( I even saw a chorus van parked outside the box on my way to work this morning) is the change over immediate or does the effect take a few days?

Depends if it's a line card swap or they are actually switching it on.

hio77

'That VDSL Cat'
12984 posts

Uber Geek

ID Verified

Trusted

Voyager

Subscriber

#2021189 23-May-2018 15:02

timmay556: Hey guys, I see that my exhange is booked in for today ( I even saw a chorus van parked outside the box on my way to work this morning) is the change over immediate or does the effect take a few days?

if you mean today, as in on the list i published...

No physical chorus man will be there, they do it remotely. It's done in the weee hours of the morning.

#include <std_disclaimer>

Any comments made are personal opinion and do not reflect directly on the position my current or past employers may have.

wratterus

1687 posts

Uber Geek

#2021205 23-May-2018 15:43

I can confirm (many thanks to BMarquis) that I have a DV130 which was running 3.8.1.2 m4 which did have Vectoring enabled on it last night - there is nothing in the UI at all to tell you that Vectoring is active. Running the 'vdsl status' command doesn't give any new info, still the [with Vectoring support] note as before.

I just flashed it with 3.8.2 m8 to check - same thing. So there is no nice green 'vectoring active' note on the dashboard for the DV130.

freakngeek

356 posts

Ultimate Geek

#2021229 23-May-2018 16:23

wratterus:I just flashed it with 3.8.2 m8 to check - same thing. So there is no nice green 'vectoring active' note on the dashboard for the DV130.

Dang, the DV2860 rich kids do, thats no fair :(

1 | ... | 15 | 16 | 17 | 18 | 19 | 20 | 21 | 22 | 23 | 24 | 25 | ... | 27