Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.




40 posts

Geek
+1 received by user: 5


Topic # 220390 8-Aug-2017 23:12
Send private message quote this post

Today's task: Replace old WinXP kiosk computer with the Win7 box i've been setting up. Display is a panasonic viera tv, maybe 42", which counts as a non-PNP monitor.
All is going well until i try and correct aspect ratio by changing the resolution (i've already changed it twice) to 1440*900, and I stupidly click ok tather than preview. Display throws a wobbly and just goes to black screen with PC mode indicator. I hook new PC up to monitor I've been using during setup and reset resolution lower. (Check, video card not stuffed). Still no display on big screen.
Next i hook up old computer. Big screen still works fine with that.
So what can I do to make the display talk to the new computer again? Connection is SVGA.

Filter this topic showing only the reply marked as answer Create new topic
860 posts

Ultimate Geek
+1 received by user: 377

Trusted
Subscriber

  Reply # 1841499 8-Aug-2017 23:15
Send private message quote this post

Are you sure the TV can actually handle 1140x900?






25212 posts

Uber Geek
+1 received by user: 5065

Moderator
Trusted
Biddle Corp
Subscriber

  Reply # 1841536 9-Aug-2017 07:15
Send private message quote this post

Why are you trying to force that resolution? I would highly doubt that you'll find any TV out there that can support that resolution. Have you looked to see what resolutions the TV does support? If the TV is a similar age to the XP machine and it's something like an old 42" Viera Plasma you'll find it only supports 1024x768 maximum despite being a 16:9 panel.

 

 

 

 


 
 
 
 


20062 posts

Uber Geek
+1 received by user: 3736

Trusted
Subscriber

  Reply # 1841547 9-Aug-2017 07:36
Send private message quote this post

Try another cable if its showing as a non pnp monitor, sounds like the edid pins are not connected and its falling back to that instead of reading what the monitor supports correctly.

 

See it a lot with people who have swapped monitors and PCs many times, but kept the same early 90's VGA cable in place because they are lazy. Even on a place with new PCs and monitors with displayport, and displayport cables in the box but using VGA because that is what went thru the hole in the desk.





Richard rich.ms

1104 posts

Uber Geek
+1 received by user: 222


  Reply # 1841846 9-Aug-2017 13:41
Send private message quote this post

It may be a refresh rate issue . Seems unlikely, but worth checking.
Also, res too low can sometimes cause issues : rare but happens .

 

Use HDMI or DVI instead of vga , it may then autodetect the correct settings .


1938 posts

Uber Geek
+1 received by user: 154


  Reply # 1841873 9-Aug-2017 14:27
Send private message quote this post

sbiddle:

 

Why are you trying to force that resolution? I would highly doubt that you'll find any TV out there that can support that resolution. Have you looked to see what resolutions the TV does support? If the TV is a similar age to the XP machine and it's something like an old 42" Viera Plasma you'll find it only supports 1024x768 maximum despite being a 16:9 panel.

 

 

 

^^ 

 

Could even be an odd one like 1366x768. More so if it is a VGA 'PC' input only. (the specs usually define this clearly in manual) HDMI/DVI-HDMI tend to be the only ones able to process the image at true 1080i resolutions. Cause well, analogue.

 

F8 on PC bootup into safe mode and adjust it back to a dumb resolution (itll be in 800x600 by default). And watch if AMD drivers. They recently started doing funny things like forcing 24Hz to mine which end in out of range errors.

 

 

 

 




40 posts

Geek
+1 received by user: 5


  Reply # 1845144 11-Aug-2017 13:08
Send private message quote this post

Addressing everyone's points:

 

The Plasma TV arrived a few weeks ago, donated by a hotel. It's not new, but in pristine condition - I'd estimate 1-3 years old. Unfortunately the mounting bracket is covering the model ID. From Panasonic manuals I've found online it looks as though it will be WXGA - 1366x768

 

The TV supports HDMI of course, but the PC doesn't (It's an ex-lease HP Elite 8300 - an office-spec box).

 

Changing the VGA cable made no difference.

 

I'm seeing the windows boot sequence (at 1024 x 768) until the user settings kick in.

 

Using Regedit from Safe Mode, under HCCC\System\ControlSet\Control\VIDEO i have about 4 branches with typical hex-string names. a couple have XResolution and YResolution values of 1440 x 900, and changing them to 800x600 doesn't fix things. Frequencies all seem to be 60Hz

 

Apparently the default resolution of the monitor I used for setup is 1440x900, so I may have to resize some web page elements once I get the display working :-)


1938 posts

Uber Geek
+1 received by user: 154


  Reply # 1845157 11-Aug-2017 13:25
Send private message quote this post

While in safemode, remove the video driver and reboot.

 

 

 

It will start with MS VGA and then install it and do a EDID detection.

 

If its the model I'm thinking of, they have digital display port. You can go DP-HDMI with ease, then it could do a better resolution.




40 posts

Geek
+1 received by user: 5


  Reply # 1847544 16-Aug-2017 13:08
Send private message quote this post

Just got back to this: Uninstalled Display driver (which is Intel HR), rebooted and got working VGA - with, of course, no widescreen modes.

 

Windows reinstalled driver automatically, asked for reboot, which I did, and... broken again.

 

Which probably means that uninstalling the driver isn't properly cleaning the settings from Registry.

 

I'm about to try a rinse and repeat, but changing the resolution in the VGA driver, to see if that overwrites anything. If not, how can I clean out the unwanted settings?


1938 posts

Uber Geek
+1 received by user: 154


  Reply # 1847558 16-Aug-2017 13:18
Send private message quote this post

http://www.majorgeeks.com/files/details/display_driver_uninstaller.html 

 

 

 

Throw on a (vga) monitor. Lower resolution to below 1366x768. Plug in VGA.

 

But it should be scaling based on info fed back. Or set a custom resolution/refresh rate.

 

 

 

But seriously,  look for a display port outlet. Pretty sure from the 8200 model up come with. Which is digital and will solve the issue with HDMI resolutions.




40 posts

Geek
+1 received by user: 5


  Reply # 1847573 16-Aug-2017 13:35
Send private message quote this post

Just to complicate things, this time Windows decided not to reinstall the drivers for the Intel Graphics - and scanning for hardware changes isn't finding it. Downloaded what I thought was the correct driver from Intel, but it said computer doesn't match.

 

 


1938 posts

Uber Geek
+1 received by user: 154




40 posts

Geek
+1 received by user: 5


  Reply # 1851220 23-Aug-2017 12:52
Send private message quote this post

HDMI to the rescue :-) Although the natural resolution at 1080p is lower than the natural resolution stated for SVGA, 1366 x 768 is working. Once I figured out how to disable overscanning.


Filter this topic showing only the reply marked as answer Create new topic



Twitter »

Follow us to receive Twitter updates when new discussions are posted in our forums:



Follow us to receive Twitter updates when news items and blogs are posted in our frontpage:



Follow us to receive Twitter updates when tech item prices are listed in our price comparison site:





News »

How Oppo shakes New Zealand’s phone market
Posted 22-Aug-2017 18:32


Recognition for top small business advisors
Posted 22-Aug-2017 17:23


OPPO R11 dual 20MP camera phone debuts in New Zealand
Posted 22-Aug-2017 15:45


Intel introduces new 8th Generation processors
Posted 21-Aug-2017 19:02


Trend Micro launches Home Network Security
Posted 21-Aug-2017 18:38


Avondale College students at top of Microsoft Office Specialist World Championship
Posted 21-Aug-2017 14:11


Garmin introduces inReach SE+ and inReach Explorer+
Posted 21-Aug-2017 14:05


Public Wi-Fi plus cloud file sharing
Posted 18-Aug-2017 11:20


D-Link NZ launches professional Wireless AC Wave 2 Access Point for businesses
Posted 17-Aug-2017 19:25


Garmin introduces the Rino 700 five-watt two-way handheld radio
Posted 17-Aug-2017 19:04


Garmin announces the Foretrex 601 and Foretrex 701 Ballistic Edition for outdoor and tactical use
Posted 17-Aug-2017 19:02


Brightstar announces new distribution partnership with Samsung Knox platform in Australia
Posted 17-Aug-2017 17:07


Free gig-enabled WiFi network extends across Dunedin
Posted 17-Aug-2017 17:04


Samsung expands with connect Gear S3 Frontier
Posted 17-Aug-2017 15:55


Fact-checking Southern Cross Next cable is fastest to USA
Posted 17-Aug-2017 13:57



Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.

Alternatively, you can receive a daily email with Geekzone updates.