Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.




587 posts

Ultimate Geek


# 139127 28-Jan-2014 19:59
Send private message

I decided to have a play around with the different channels on my router (Linksys WAG120N) and see how the signal strength is. I have found that my PS4 and my computer says that they are picking up channel 7 when my router says I am on channel 9, whats up with this?









Filter this topic showing only the reply marked as answer Create new topic
5525 posts

Uber Geek


  # 976196 28-Jan-2014 20:11
Send private message

Router is set to use 40MHz wide channels, but your devices are only connecting at 20Mhz narrow channel. The 20MHz only channel will be set as the lower, channel 7.

17345 posts

Uber Geek

Trusted

  # 976246 28-Jan-2014 21:16
Send private message

Speaking of 40Mhz, when I have my TP-Link W8960N on 40, its unstable, is there a setting that will assist that in any way, or is it the nature of the beast? 20mhz is rock solid

 
 
 
 


5525 posts

Uber Geek


  # 976253 28-Jan-2014 21:26
Send private message

Updated firmware perhaps? 40MHz isn't in itself inherently unstable.

17345 posts

Uber Geek

Trusted

  # 976271 28-Jan-2014 21:47
Send private message

Yeah good point. Its been so rock solid I never bothered, will try that

2651 posts

Uber Geek

Trusted

  # 976273 28-Jan-2014 21:50
Send private message
5525 posts

Uber Geek


  # 976276 28-Jan-2014 22:00
Send private message

40MHz is a wider channel, so in general terms, higher throughput if both the AP and client support it.

It's not uncommon for devices to support only 20MHz (standard) width channels on 2.4GHz, because it's the neighbourly thing to do - a single 40MHz channel can overlap almost every other 2.4GHz channel, causing issues for other nearby networks. Channels are separated more on 5GHz, so not so much of an issue.

Neither is better as such, each has pros and cons.

17345 posts

Uber Geek

Trusted

  # 976280 28-Jan-2014 22:05
Send private message

sonyxperiageek: Which one is usually better - 20 or 40?


AFAIK 40 is better, channel bonding. But more susceptible to interference on 2.4, and I think only one or two channels dont overlap, limiting the ability to choose a channel that is in low use by neighbours. And I think it needs to be set to N and not b/g/n? Leaving my 15yo daughter out in the cold with her 3GS?

 
 
 
 


6615 posts

Uber Geek
Inactive user


  # 976286 28-Jan-2014 22:17
Send private message

Careful with Apple devices and 40Mhz, AFAIK they dont support it at all??

2651 posts

Uber Geek

Trusted

  # 976289 28-Jan-2014 22:21
One person supports this post
Send private message

tdgeek:
sonyxperiageek: Which one is usually better - 20 or 40?


AFAIK 40 is better, channel bonding. But more susceptible to interference on 2.4, and I think only one or two channels dont overlap, limiting the ability to choose a channel that is in low use by neighbours. And I think it needs to be set to N and not b/g/n? Leaving my 15yo daughter out in the cold with her 3GS?


I guess a dual band router would help?




17345 posts

Uber Geek

Trusted

  # 976319 28-Jan-2014 22:42
Send private message

sonyxperiageek:
tdgeek:
sonyxperiageek: Which one is usually better - 20 or 40?


AFAIK 40 is better, channel bonding. But more susceptible to interference on 2.4, and I think only one or two channels dont overlap, limiting the ability to choose a channel that is in low use by neighbours. And I think it needs to be set to N and not b/g/n? Leaving my 15yo daughter out in the cold with her 3GS?


I guess a dual band router would help?


TimA is right, they do not support 40Mhz, so you get the added interference possibility/probability and no gain in bandwidth and likely that the interference may cost more than the extra bandwidth, which they cannot even use. From what I read tonight, 2.4 40Mhz seems a bad idea for the most users and/or neighbour devices.

Solution? Easy, get a simultaneous dual band wifi router. iPhone 4S (I think) and up supports 5Ghz  at 40Mhz bandwidth. Best of every world??

I'll maybe get an Airport Extreme and turn off the AP on the 8960N
 


4025 posts

Uber Geek

Trusted

  # 976338 28-Jan-2014 23:12
Send private message

TimA: Careful with Apple devices and 40Mhz, AFAIK they dont support it at all??

They don't. However they work just fine on every 40mhz network i've connected to. As all the other devices i've had experience with.
I use 40mhz as theres no wifi congestion here and i can crank up to 18MB/s over 2.4 40mhz. If there was, i wouldn't use it as it would probably make the situation worse, rather than better.

5525 posts

Uber Geek


  # 976395 29-Jan-2014 07:31
Send private message

TimA: Careful with Apple devices and 40Mhz, AFAIK they dont support it at all??


Not correct.

They do not support 40MHz on 2.4GHz in order to reduce interference with neighbouring networks, but do support 40MHz on 5GHz where the radio channels are wider. This has been the case since the first 802.11n Airport Extreme was introduced in Jan 2007. Same applies to Apple desktops / laptops.

The exception is some (mostly earlier) iOS devices that had more limited WiFi, presumably as a cost saving measure, and high speed wasn't required for the sorts of things it was expected you would do with them. In these cases, devices are often limited to 2.4GHz only, which will be 20MHz channels.



3385 posts

Uber Geek

Trusted

  # 976839 29-Jan-2014 17:50
Send private message

tdgeek: Speaking of 40Mhz, when I have my TP-Link W8960N on 40, its unstable, is there a setting that will assist that in any way, or is it the nature of the beast? 20mhz is rock solid


Using a 40mhz wide channel will make you susceptible to more interference.
Another router or device with a 20mhz width could come and occupy part of that 40mhz worth of bandwidth. It is also usually the case that a 40mhz channel has half the output of a 20mhz because the transmit power is spread over a wider bandwidth. So your noise margin - that is the difference between your signal and background noise is less so it wont be as stable.

40mhz should really only be used for high speed + short distance.




Ray Taylor
Taylor Broadband (rural hawkes bay)
www.ruralkiwi.com

There is no place like localhost
For my general guide to extending your wireless network Click Here




Filter this topic showing only the reply marked as answer Create new topic



Twitter and LinkedIn »



Follow us to receive Twitter updates when new discussions are posted in our forums:



Follow us to receive Twitter updates when news items and blogs are posted in our frontpage:



Follow us to receive Twitter updates when tech item prices are listed in our price comparison site:





News »

Intel expands 10th Gen Intel Core Mobile processor family
Posted 23-Aug-2019 10:22


Digital innovation drives new investment provider
Posted 23-Aug-2019 08:29


Catalyst Cloud becomes a Kubernetes Certified Service Provider (KCSP)
Posted 23-Aug-2019 08:21


New AI legaltech product launched in New Zealand
Posted 21-Aug-2019 17:01


Yubico launches first Lightning-compatible security key, the YubiKey 5Ci
Posted 21-Aug-2019 16:46


Disney+ streaming service confirmed launch in New Zealand
Posted 20-Aug-2019 09:29


Industry plan could create a billion dollar interactive games sector
Posted 19-Aug-2019 20:41


Personal cyber insurance a New Zealand first
Posted 19-Aug-2019 20:26


University of Waikato launches space for esports
Posted 19-Aug-2019 20:20


D-Link ANZ expands mydlink ecosystem with new mydlink Mini Wi-Fi Smart Plug
Posted 19-Aug-2019 20:14


Kiwi workers still falling victim to old cyber tricks
Posted 12-Aug-2019 20:47


Lightning Lab GovTech launches 2019 programme
Posted 12-Aug-2019 20:41


Epson launches portable laser projector
Posted 12-Aug-2019 20:27


Huawei launches new distributed HarmonyOS
Posted 12-Aug-2019 20:20


Lenovo introduces single-socket servers for edge and data-intensive workloads
Posted 9-Aug-2019 21:26



Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.


Support Geekzone »

Our community of supporters help make Geekzone possible. Click the button below to join them.

Support Geezone on PressPatron



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.

Alternatively, you can receive a daily email with Geekzone updates.