Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.




13 posts

Geek


Topic # 220308 4-Aug-2017 19:53
Send private message quote this post

Recently, I brought a Netcomm NF17ACV router modem from PB tech due to the fact that the Huawei router from spark literally died within two months and instead I brought a Netcomm NF17ACV because according to PB Tech, it is compatible with Spark's Ultra Fast Broadband network. When I spoke to a Spark service center agent, I was sent the following specifications:

 

    Operating Mode : MDI/MDIX

 

    PPP Protocol : PPPoE

 

    PPP Username: user@spark.co.nz

 

    PPP Password: password

 

    PPP Auth Type : PAP

 

    PPP Mode : Always on (Dial on Demand disabled)

 

    Encapsulation : 802.1Q

 

    PCP Marking : 0

 

    VID (or VLAN) : 10

 

    MTU : 1,500 or AUTO

I would like to know how do I make the Netcomm NF17ACV modem or router run on the MDI or MDIX operating mode as specified by Spark and overall the settings provided by Spark which should be implemented into the Netcomm NF17ACV modem or router


View this topic in a long page with up to 500 replies per page Create new topic
 1 | 2
'That VDSL Cat'
6263 posts

Uber Geek
+1 received by user: 1172

Trusted
Spark
Subscriber

  Reply # 1839345 4-Aug-2017 19:55
Send private message quote this post

The extra line from this was missed.

 

 

Note: You may not be prompted for all values. A specific PPP username and password are not required, but you will not be able to connect if either field is blank.

 

 

 

 

Essentially you may need to create a WAN_VLAN10 interface on the NF16ACV.

 

From there you will add a PPPoE Connection with the username/password and it will be good to go.





#include <std_disclaimer>

 

Any comments made are personal opinion and do not reflect directly on the position my current or past employers may have.




13 posts

Geek


  Reply # 1839346 4-Aug-2017 19:57
Send private message quote this post

hio77:

 

The extra line from this was missed.

 

 

Note: You may not be prompted for all values. A specific PPP username and password are not required, but you will not be able to connect if either field is blank.

 

 

 

 

Essentially you may need to create a WAN_VLAN10 interface on the NF16ACV.

 

From there you will add a PPPoE Connection with the username/password and it will be good to go.

 



How do I create a WAN_VLAN10 on the NF17ACV, I might need some help


 
 
 
 


6682 posts

Uber Geek
+1 received by user: 2108

Subscriber

  Reply # 1839370 4-Aug-2017 20:57
Send private message quote this post

advanced setup > WAN Service > ADD, then enter the information for the fibre connection




13 posts

Geek


  Reply # 1839371 4-Aug-2017 21:02
Send private message quote this post

Jase2985:

 

advanced setup > WAN Service > ADD, then enter the information for the fibre connection

 



Thanks for the help, I have one more inquiry for the PPP username and PPP password, would using address like @xtra.co.nz since my father has a spark account which still uses the xtra.co.nz be fine?

Also will the PPP password be the same as the xtra email password?


6682 posts

Uber Geek
+1 received by user: 2108

Subscriber

  Reply # 1839372 4-Aug-2017 21:05
Send private message quote this post

use what they show you in the guide as the username and password

 

they use port based authentication so there just needs to be something in there. doesnt matter what it is.




13 posts

Geek


  Reply # 1839379 4-Aug-2017 21:41
Send private message quote this post

Jase2985:

 

use what they show you in the guide as the username and password

 

they use port based authentication so there just needs to be something in there. doesnt matter what it is.

 



I just tried using my dad's xtra email address for the PPP port authentication it did not work


6682 posts

Uber Geek
+1 received by user: 2108

Subscriber

  Reply # 1839382 4-Aug-2017 21:48
Send private message quote this post

just use the ones provided in the spark information

 

Username: user@spark.co.nz
Password: password

 

exactly as its written there

 

you may not have the rest of the settings correct


871 posts

Ultimate Geek
+1 received by user: 166


  Reply # 1839383 4-Aug-2017 21:51
Send private message quote this post

Make sure you have configured a Layer 2 ETH interface, this is also under Advanced Setup down the left hand side menu.

 

 

Connection type should be VlanMux.

 

 




13 posts

Geek


  Reply # 1839387 4-Aug-2017 22:04
Send private message quote this post

yitz: Make sure you have configured a Layer 2 ETH interface, this is also under Advanced Setup down the left hand side menu. Connection type should be VlanMux.


I have done that







871 posts

Ultimate Geek
+1 received by user: 166


  Reply # 1839389 4-Aug-2017 22:10
Send private message quote this post

In the first screenshot when you are adding a WAN service ptm0/(0_1_1) is the VDSL interface, you need to add it to the eth0/LANx interface.



13 posts

Geek


  Reply # 1839390 4-Aug-2017 22:13
Send private message quote this post

yitz: In the first screenshot when you are adding a WAN service ptm0/(0_1_1) is the VDSL interface, you need to add it to the eth0/LANx interface.


Edit: managed to add it


871 posts

Ultimate Geek
+1 received by user: 166


  Reply # 1839391 4-Aug-2017 22:18
Send private message quote this post

You need to go into ETH interface down the left hand side. If there is an existing entry, tick Remove and then Apply. Then choose Add to create an ETH interface with Connection type VlanMux.

 

 

Then go back into WAN service down the left hand side and create a new WAN service and choose eth0 from the drop down menu (choosing from atm0, ptm0 and eth0) and proceed as you had before.



13 posts

Geek


  Reply # 1839392 4-Aug-2017 22:19
Send private message quote this post

I have managed to change it to eth0


6682 posts

Uber Geek
+1 received by user: 2108

Subscriber

  Reply # 1839405 5-Aug-2017 06:17
Send private message quote this post

from what i can see, your authentication method is incorrect and not the PAP that spark say in their guide




13 posts

Geek


  Reply # 1839462 5-Aug-2017 10:24
Send private message quote this post

Jase2985:

 

from what i can see, your authentication method is incorrect and not the PAP that spark say in their guide

 



I have done a new configuration this morning, screenshots attached:










 1 | 2
View this topic in a long page with up to 500 replies per page Create new topic



Twitter »

Follow us to receive Twitter updates when new discussions are posted in our forums:



Follow us to receive Twitter updates when news items and blogs are posted in our frontpage:



Follow us to receive Twitter updates when tech item prices are listed in our price comparison site:





News »

Public Wi-Fi plus cloud file sharing
Posted 18-Aug-2017 11:20


D-Link NZ launches professional Wireless AC Wave 2 Access Point for businesses
Posted 17-Aug-2017 19:25


Garmin introduces the Rino 700 five-watt two-way handheld radio
Posted 17-Aug-2017 19:04


Garmin announces the Foretrex 601 and Foretrex 701 Ballistic Edition for outdoor and tactical use
Posted 17-Aug-2017 19:02


Brightstar announces new distribution partnership with Samsung Knox platform in Australia
Posted 17-Aug-2017 17:07


Free gig-enabled WiFi network extends across Dunedin
Posted 17-Aug-2017 17:04


Samsung expands with connect Gear S3 Frontier
Posted 17-Aug-2017 15:55


Fact-checking Southern Cross Next cable is fastest to USA
Posted 17-Aug-2017 13:57


Thurrott says Microsoft Surface is dead last for reliability
Posted 16-Aug-2017 15:19


LibreOffice 5.4 works better with Microsoft Office files
Posted 16-Aug-2017 13:32


Certus launches Cognition
Posted 14-Aug-2017 09:31


Spark adds Cambridge, Turangi to 4.5G network
Posted 10-Aug-2017 17:55


REANNZ network to receive ongoing Government funding through to 2024
Posted 10-Aug-2017 16:05


Chorus backhaul starts with 2degrees
Posted 10-Aug-2017 15:49


New Zealanders cool on data analytics catching benefit fraud
Posted 10-Aug-2017 09:56



Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.

Alternatively, you can receive a daily email with Geekzone updates.