Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.


1417 posts

Uber Geek
+1 received by user: 149

Subscriber

Topic # 228612 14-Jan-2018 14:12
Send private message quote this post

Hi

 

Following on from my earlier thread, I've now got my USG and its working fine with the DV130 in bridge mode.  I now want to configure the DV130<>USG connection to allow me to see the GUI of the DV130, I am currently unable to do that as it is bridged. 

 

I know it involves static routes I believe on both units but does someone have a good method of doing this?  I'm presuming if I need to set the DV130 on a static LAN of 192.168.0.1 for example and then route to the USG IP of 192.168.1.1; and do the same on the USG but in reverse?

 

Thanks,

 

Chris


Create new topic
1214 posts

Uber Geek
+1 received by user: 273


  Reply # 1938654 14-Jan-2018 16:07
Send private message quote this post

You'll need to assign a second WAN interface on the USG with IP of 192.168.0.x (on the DV130's range), this will allow communication between the DV130 and the USG. In order to access from a host on the USG LAN (192.168.1.x) you will need to create a NAT rule so that traffic destined to the DV130 (say 192.168.0.1) appears to originate from the USG (e.g. 192.168.0.2).

 

 

Sorry I don't have a USG so can't give you definitive instructions on how to add that to its config.

295 posts

Ultimate Geek
+1 received by user: 73


  Reply # 1938661 14-Jan-2018 16:36
Send private message quote this post

No idea if USG uses same language as ERL3 but here is what I do to see devices on the WAN side of router
My DV130 is 400m away at road and gets PtP from home to road, with 2x Radios
I like you needed to see these devices from network.

 

ETH0 = WAN is 192.168.1.xxx
ETH1 = LAN is 192.168.0.xxx

Commands to run to enable viewing of WAN interface:

 

configure
set service nat rule 5000 description 'Clients on WAN side'
set service nat rule 5000 destination address 192.168.1.0/24
set service nat rule 5000 outbound-interface eth0
set service nat rule 5000 source address 192.168.0.1/24
set service nat rule 5000 type masquerade
commit
save

 

Do NOT make the DV130 ip 192.168.x.1 as the USG will use that

 

Hope this helps.




1417 posts

Uber Geek
+1 received by user: 149

Subscriber

  Reply # 1938685 14-Jan-2018 17:11
Send private message quote this post

The USG uses EdgeOS except that you have to do some stuff with json to get it to save permanently.

 

What's your configuration for the Draytek?  Would you mind getting a screen shot, sans any password or sensitive stuff so I can make sure the settings are correct?

 

 


21218 posts

Uber Geek
+1 received by user: 4268

Trusted
Subscriber

  Reply # 1938696 14-Jan-2018 17:48
Send private message quote this post

Its absurd that they cant do this by default on the USG - If I put a netgear (or may have been linksys - whatever a cheapie consumer one) router upstream of my draytek then I can see its UI, Otherwise I cant.

 

I chucked a dumb switch between them and just plug a pc in when I want to see what the terrible sync speeds are at any time.





Richard rich.ms

64 posts

Master Geek
+1 received by user: 5


  Reply # 1991690 8-Apr-2018 21:52
Send private message quote this post

Not sure what a USG is, but in general with a vigor, i plug the vigor into a LAN port on the router, so i can access it from the internal network.  Then i plug the WAN port on the router into a LAN port on the router, so that the router can find the vigor also.


169 posts

Master Geek
+1 received by user: 31


  Reply # 2013677 10-May-2018 23:18
Send private message quote this post

Benoire:

The USG uses EdgeOS except that you have to do some stuff with json to get it to save permanently.


What's your configuration for the Draytek?  Would you mind getting a screen shot, sans any password or sensitive stuff so I can make sure the settings are correct?


 



I have this setup at home and from memory, I needed to configure a static route on the DV130. Also the DV130 had to be configured for PPPoE pass-through and not specifically in bridge mode.

Create new topic

Twitter »

Follow us to receive Twitter updates when new discussions are posted in our forums:



Follow us to receive Twitter updates when news items and blogs are posted in our frontpage:



Follow us to receive Twitter updates when tech item prices are listed in our price comparison site:





News »

Microsoft Dynamics 365 Business Central launches
Posted 10-Jul-2018 10:40


Spark completes first milestone in voice platform upgrade
Posted 10-Jul-2018 09:36


Microsoft ices heated developers
Posted 6-Jul-2018 20:16


PB Technologies charged for its extended warranties and warned for bait advertising
Posted 3-Jul-2018 15:45


Almost 20,000 people claim credits from Spark
Posted 29-Jun-2018 10:40


Cove sells NZ's first insurance policy via chatbot
Posted 25-Jun-2018 10:04


N4L helping TAKA Trust bridge the digital divide for Lower Hutt students
Posted 18-Jun-2018 13:08


Winners Announced for 2018 CIO Awards
Posted 18-Jun-2018 13:03


Logitech Rally sets new standard for USB-connected video conference cameras
Posted 18-Jun-2018 09:27


Russell Stanners steps down as Vodafone NZ CEO
Posted 12-Jun-2018 09:13


Intergen recognised as 2018 Microsoft Country Partner of the Year for New Zealand
Posted 12-Jun-2018 08:00


Finalists Announced For Microsoft NZ Partner Awards
Posted 6-Jun-2018 15:12


Vocus Group and Vodafone announce joint venture to accelerate fibre innovation
Posted 5-Jun-2018 10:52


Kogan.com to launch Kogan Mobile in New Zealand
Posted 4-Jun-2018 14:34


Enable doubles fibre broadband speeds for its most popular wholesale service in Christchurch
Posted 2-Jun-2018 20:07



Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.

Alternatively, you can receive a daily email with Geekzone updates.