Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.


psmi045

22 posts

Geek


#236320 28-May-2018 18:47
Send private message

When I setup my shinny new Ubiquiti Edgerouter 4 last week, I only set it up for PPPOE using IP4 to BigPipe. Since they're shutting down their IPv6 trial I didn't think it would make sense to have a go at using IPv6.

 

Anyway, every second I see it logging:

 

pppd[1849]: Unsupported protocol 'IPv6 Control Protocol' (0x8057) received

 

Alas, I'm still learning this router's "ways", and I can't figure out how to get it to do something more constructive than just repeating itself. Perhaps it will go away when Bigpipe finally turn off IPv6, but I'm wondering if there is something I can do to make the router happier.


Filter this topic showing only the reply marked as answer Create new topic
freakngeek
350 posts

Ultimate Geek


  #2024131 28-May-2018 19:01
Send private message

Here is how I setup IPV6 via pppoe Unlimited Internet on a ERL3

 

WAN is on eth0 in CLI do the following:

 

configure
set interfaces ethernet eth0 pppoe 0 dhcpv6-pd pd 0 interface eth0 host-address '::1'
set interfaces ethernet eth0 pppoe 0 dhcpv6-pd pd 0 interface eth0 prefix-id ':2'
set interfaces ethernet eth0 pppoe 0 dhcpv6-pd pd 0 interface eth0 service slaac
set interfaces ethernet eth0 pppoe 0 dhcpv6-pd pd 0 interface eth1 host-address '::1'
set interfaces ethernet eth0 pppoe 0 dhcpv6-pd pd 0 interface eth1 prefix-id ':0'
set interfaces ethernet eth0 pppoe 0 dhcpv6-pd pd 0 interface eth1 service slaac
set interfaces ethernet eth0 pppoe 0 dhcpv6-pd pd 0 interface eth2 host-address '::1'
set interfaces ethernet eth0 pppoe 0 dhcpv6-pd pd 0 interface eth2 prefix-id ':1'
set interfaces ethernet eth0 pppoe 0 dhcpv6-pd pd 0 interface eth2 service slaac
set interfaces ethernet eth0 pppoe 0 dhcpv6-pd pd 0 prefix-length /56
set interfaces ethernet eth0 pppoe 0 dhcpv6-pd rapid-commit enable
set interfaces ethernet eth0 pppoe 0 ipv6 dup-addr-detect-transmits 1
set interfaces ethernet eth0 pppoe 0 ipv6 enable

 

set protocols static interface-route6 '::/0' next-hop-interface pppoe0
commit
save (only if it works)

 

Now from memory Bigpipe uses a prefix-length of /60
I have a slaac for each Ethernet port including WAN as I have Radio's to modem on that

 

 

 

Hope this helps.


psmi045

22 posts

Geek


  #2024133 28-May-2018 19:04
Send private message

These commands seem to have fixed it. Now to figure out some firewall rules to drop everything IPv6

 

set interfaces ethernet eth0 pppoe 0 ipv6 address autoconf

 

set interfaces ethernet eth0 pppoe 0 ipv6 dup-addr-detect-transmits 1

 

set interfaces ethernet eth0 pppoe 0 ipv6 enable

 

 


 
 
 
 


freakngeek
350 posts

Ultimate Geek


  #2024134 28-May-2018 19:07
Send private message

#IPv6 rules
set firewall ipv6-name WAN6_IN default-action drop
set firewall ipv6-name WAN6_IN rule 10 action accept
set firewall ipv6-name WAN6_IN rule 10 description 'allow established'
set firewall ipv6-name WAN6_IN rule 10 protocol all
set firewall ipv6-name WAN6_IN rule 10 state established enable
set firewall ipv6-name WAN6_IN rule 10 state related enable
set firewall ipv6-name WAN6_IN rule 20 action drop
set firewall ipv6-name WAN6_IN rule 20 description 'drop invalid packets'
set firewall ipv6-name WAN6_IN rule 20 protocol all
set firewall ipv6-name WAN6_IN rule 20 state invalid enable
set firewall ipv6-name WAN6_IN rule 30 action accept
set firewall ipv6-name WAN6_IN rule 30 description 'allow ICMPv6'
set firewall ipv6-name WAN6_IN rule 30 protocol icmpv6

 

set firewall ipv6-name WAN6_LOCAL default-action drop
set firewall ipv6-name WAN6_LOCAL rule 10 action accept
set firewall ipv6-name WAN6_LOCAL rule 10 description 'allow established'
set firewall ipv6-name WAN6_LOCAL rule 10 protocol all
set firewall ipv6-name WAN6_LOCAL rule 10 state established enable
set firewall ipv6-name WAN6_LOCAL rule 10 state related enable
set firewall ipv6-name WAN6_LOCAL rule 20 action accept
set firewall ipv6-name WAN6_LOCAL rule 20 description 'allow ICMPv6'
set firewall ipv6-name WAN6_LOCAL rule 20 protocol icmpv6
set firewall ipv6-name WAN6_LOCAL rule 30 action accept
set firewall ipv6-name WAN6_LOCAL rule 30 description 'allow DHCPv6 client/server'
set firewall ipv6-name WAN6_LOCAL rule 30 destination port 546
set firewall ipv6-name WAN6_LOCAL rule 30 protocol udp
set firewall ipv6-name WAN6_LOCAL rule 40 action drop
set firewall ipv6-name WAN6_LOCAL rule 40 description 'drop invalid packets'
set firewall ipv6-name WAN6_LOCAL rule 40 protocol all
set firewall ipv6-name WAN6_LOCAL rule 40 state invalid enable
set firewall ipv6-receive-redirects disable
set firewall ipv6-src-route disable

 

set interfaces ethernet eth0 pppoe 0 firewall in ipv6-name WAN6_IN
set interfaces ethernet eth0 pppoe 0 firewall local ipv6-name WAN6_LOCAL


psmi045

22 posts

Geek


  #2024137 28-May-2018 19:12
Send private message

Thanks! Excellent.


Filter this topic showing only the reply marked as answer Create new topic





News »

Nanoleaf enhances lighting line with launch of Triangles and Mini Triangles
Posted 17-Oct-2020 20:18


Synology unveils DS1621+ 
Posted 17-Oct-2020 20:12


Ingram Micro introduces FootfallCam to New Zealand channel
Posted 17-Oct-2020 20:06


Dropbox adopts Virtual First working policy
Posted 17-Oct-2020 19:47


OPPO announces Reno4 Series 5G line-up in NZ
Posted 16-Oct-2020 08:52


Microsoft Highway to a Hundred expands to Asia Pacific
Posted 14-Oct-2020 09:34


Spark turns on 5G in Auckland
Posted 14-Oct-2020 09:29


AMD Launches AMD Ryzen 5000 Series Desktop Processors
Posted 9-Oct-2020 10:13


Teletrac Navman launches integrated multi-camera solution for transport and logistics industry
Posted 8-Oct-2020 10:57


Farmside hits 10,000 RBI customers
Posted 7-Oct-2020 15:32


NordVPN starts deploying colocated servers
Posted 7-Oct-2020 09:00


Google introduces Nest Wifi routers in New Zealand
Posted 7-Oct-2020 05:00


Orcon to bundle Google Nest Wifi router with new accounts
Posted 7-Oct-2020 05:00


Epay and Centrapay partner to create digital gift cards
Posted 2-Oct-2020 17:34


Inseego launches 5G MiFi M2000 mobile hotspot
Posted 2-Oct-2020 14:53









Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.


Support Geekzone »

Our community of supporters help make Geekzone possible. Click the button below to join them.

Support Geezone on PressPatron



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.

Alternatively, you can receive a daily email with Geekzone updates.