Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.


61 posts

Master Geek
+1 received by user: 6


Topic # 115432 25-Mar-2013 21:40
Send private message

Hi,

Just wondering what advice people have on the best way to reliably join two lengths of Cat5e cable. 

I have some solid core armoured Cat5 running about 8 meters out to a pair of 20,000L underground water tanks. The cable comes up through a sleeve in the foundation and was left disconnected behind a blank wall plate.  There is a second solid core Cat5e cable behind the blank faceplate running about another 8m back to the 'storage' room where it's terminated with a single RJ45 faceplate rather than on the patch panel so as not to be confused with the normal network runs.

The reason for having all of this is to remotely monitor the water level in the tanks using an HC-SR04 ultrasonic transducer mounted on the tank ceiling to measure the distance down to the water surface.  I was planning on putting just the transducer in the tank, and an Arduino back in the storage room.  Alternatively I could put both the Arduino and transducer in tank and power it using PoE.

Any recommendations on the best way to join these two cables, or the merits of having the Arduino in the tank with the sensor rather than back in the less hostile environment of the storage room would be appreciated.


Create new topic
399 posts

Ultimate Geek
+1 received by user: 171

Subscriber

  Reply # 786957 25-Mar-2013 22:08
One person supports this post
Send private message

Hi

Best method would be a punch down joiner such as:
http://www.computerstore.co.nz/A-PD-C6.aspx
Sorry can't comment on best position for the Arduino.

1594 posts

Uber Geek
+1 received by user: 327

Lifetime subscriber

  Reply # 786992 26-Mar-2013 06:34
Send private message

you could use the gel filled IDC connectors (just like the chorus guys use), they are only a few cents each from places like Ja Russell or Ideal

6300 posts

Uber Geek
+1 received by user: 288

Trusted
Subscriber

  Reply # 787005 26-Mar-2013 07:59
Send private message

Hi, yes if its not for data then scotch locs (gel filled IDC's) are the best.

Cyril

3404 posts

Uber Geek
+1 received by user: 399

Trusted

  Reply # 787032 26-Mar-2013 09:24
Send private message

So are scotch locks not good enough for standard copper ethernet?





6300 posts

Uber Geek
+1 received by user: 288

Trusted
Subscriber

  Reply # 787035 26-Mar-2013 09:29
Send private message

Hi no you cannot maintain HF transmission line impedance with scotch locs, I have seen in the US a two conductor scotch loc that is designed to maintain the impedance of each pair and is Class D rated (ie 100MHz) but never seen them here.

I was under the impression that the OP was using these for some lower frequency telemetry purpose, hence scotch locs are fine, you can maintain reasonable performance to 20-30MHz is you keep untwist to a minimum as VDSL2 performance shows.

Cyril

5247 posts

Uber Geek
+1 received by user: 2265

Trusted
Lifetime subscriber

  Reply # 787053 26-Mar-2013 10:22
One person supports this post
Send private message

You could just terminate both to RJ45 wall sockets, then plug in a short patch lead between them. This give the advantage of later putting in a network switch should you in future put something in here that is IP.




Chorus has spent $1.4 billion on making their xDSL broadband network faster. If your still stuck on ADSL or VDSL, why not spend from $150 on a master filter install to make sure you are getting the most out of your connection?
I install - Naked DSL, DSL Master Splitters, VoIP, data cabling and general computer support for home and small business.
Rural Broadband RBI installer for Ultimate Broadband and Full Flavour

 

Need help in Auckland, Waikato or BoP? Click my email button, or email me direct: [my user name] at geekzonemail dot com


734 posts

Ultimate Geek
+1 received by user: 27

Trusted

  Reply # 787079 26-Mar-2013 10:55
Send private message

Duct tape!

On a more serious note, those gel filled IDC's are great




Homebuilt High Performance Desktop: Windows 10 Professional (x64)
Toshiba Encore Write 2: Windows 10
Nokia 930: Windows Phone 10
Samsung Tab4 7": Android Lolipop
XBL: CruciasNZ
PSN: CruciasNZ
Steam: Lienhart2005


Create new topic

Twitter »

Follow us to receive Twitter updates when new discussions are posted in our forums:



Follow us to receive Twitter updates when news items and blogs are posted in our frontpage:



Follow us to receive Twitter updates when tech item prices are listed in our price comparison site:



Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.

Alternatively, you can receive a daily email with Geekzone updates.