Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.
Filter this topic showing only the reply marked as answer View this topic in a long page with up to 500 replies per page Create new topic
1 | 2 
Meow
8018 posts

Uber Geek
+1 received by user: 4006

Moderator
Trusted
Lifetime subscriber

  Reply # 1616522 23-Aug-2016 20:14
Send private message

kingP:

 

ignore if its a dumb question but.... is it a DCHP lease period type issue?

Should I leave it setup for a few hours in order to be issued a new IP / turn off the UNT for half and hour and start it back up?

At present I have been waiting say 15 - 20 mins then trying again.

 

 

No it should be fine. The configuration looks fine also. I'll need more information such as logs from your router to see where it is going wrong...





I fix stuff!
1708 posts

Uber Geek
+1 received by user: 381

Trusted
Vocus
Subscriber

  Reply # 1616629 24-Aug-2016 09:13
Send private message

Can you also confirm the NF4V works when you connect that to the ONT. The Edge router needs to plug into the same port on the ONT. Not all the ports work.

 

 

 

 




72 posts

Master Geek
+1 received by user: 2


  Reply # 1616971 24-Aug-2016 17:29
Send private message

Sounddude:

 

Can you also confirm the NF4V works when you connect that to the ONT. The Edge router needs to plug into the same port on the ONT. Not all the ports work.

 

 

 

 

Yea the NF4V works but has been having a mixture of issues DNS, dropping connection restarts needed.

 

 




72 posts

Master Geek
+1 received by user: 2


  Reply # 1619267 29-Aug-2016 18:46
Send private message

So in the end I threw in the towel and got a networking mate in

 

Good news: Orcon can use 3rd party routers

 

Bad news: He got it work but unfortunately he used a config file he already had so im not 100% on what needed fixing other than the Masquerade rules needed setting up.

 

 

 

Long story short, get in the pro's!


59 posts

Master Geek
+1 received by user: 1


  Reply # 1632310 17-Sep-2016 19:54
Send private message

Hi I'm with Orcon and having just bought a ERL lite, trying to get it set up with UFB,

 

I have already spent a couple of hours on to it with the help from these threads (have to minimise i/net outage because of kids, even 10mins outage they think is bad!!!!)

 

I have used the ERL basic wizard to setup, when I compare the 'configure' screen dumps from the CLI in this thread, they look the same 

 

 

 

Anyway, I must be missing something in the config as I have the VLAN, eth0, lan 1, shows all 'connected' Status, in the vlan I get the external IP address assigned by orcon etc

 

DCHP works and I can connect to the network but no internet

 

Dont think its firewall as I have tried a config with no rules, still no i/net

 

what to check next??

 

 

 

 

 

 


59 posts

Master Geek
+1 received by user: 1


  Reply # 1632372 18-Sep-2016 08:59
Send private message

Got it sorted cry !!!

 

So i used the basic config wizard, previously user KingP said there were some Masquerade rules needed changing, all I had to do was point the outbound interface to the vlan (as the basic config wizard had set it to eth0 instead)

 

Firewall/NAT>NAT>Actions>Config select Masquerade

 

Click to see full size

 

 

 

 

 

 

 

 

 

 

 

 




72 posts

Master Geek
+1 received by user: 2


  Reply # 1635389 18-Sep-2016 12:29
Send private message

hbngan:

 

Got it sorted cry !!!

 

So i used the basic config wizard, previously user KingP said there were some Masquerade rules needed changing, all I had to do was point the outbound interface to the vlan (as the basic config wizard had set it to eth0 instead)

 

Firewall/NAT>NAT>Actions>Config select Masquerade

 

 

 

 

 

This works perfectly, thanks!!

 

I just did a fresh install using this and it worked a treat. 


16 posts

Geek
+1 received by user: 3


  Reply # 1646783 6-Oct-2016 16:58
Send private message

Guys, i just got moved to Orcon 1Gb plan, the fritzbox is working 100% but with the EdgeRouter Lite im only getting close to 200/200, DPI is off, no port forwarding, no bridge mode.

 

 

 

Any ideas?


1 | 2 
Filter this topic showing only the reply marked as answer View this topic in a long page with up to 500 replies per page Create new topic

Twitter »

Follow us to receive Twitter updates when new discussions are posted in our forums:



Follow us to receive Twitter updates when news items and blogs are posted in our frontpage:



Follow us to receive Twitter updates when tech item prices are listed in our price comparison site:



Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.

Alternatively, you can receive a daily email with Geekzone updates.