Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.




7 posts

Wannabe Geek


# 42769 9-Oct-2009 23:24
Send private message

Heya everyone


Normally I love Orcon, they generally have good speeds and good service, but unfortunately since i have moved to my new house the connections I am getting are very poor.


let me define very poor... the speed that the link establishes is dismal, see stats below...


Also the link drops out all the time.... I only have 3 jackpoints in the house, have checked all the wiring for corrosion, there is no alarm and no sky to get in the way.  I have tried different modems, different filters... even having nothing else connected to any lines anywhere.


I have spoken to orcon and they pushed out a different profile that increase the signal, but this has not made a huge difference, maybe made the connections active for a few more min.  , normall my connection is not as slow as listed below... but during peak times it does drop down this slow.. if i did a speed test with this connection - if it even loads, i get around 56k


Bar getting Orcon out to check the lines is there anything else i need to consider?


Link Information
Uptime:
0 days, 0:19:22
DSL Type:
G.992.5 annex A
Bandwidth (Up/Down) [kbps/kbps]:
514 / 347
Data Transferred (Sent/Received) [kB/kB]:
0,00 / 0,00
Output Power (Up/Down) [dBm]:
10,0 / 0,0
Line Attenuation (Up/Down) [dB]:
24,5 / 44,0
SN Margin (Up/Down) [dB]:
14,5 / 18,0
Vendor ID (Local/Remote):
TMMB / IFTN
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
Loss of Link (Remote):
0
Error Seconds (Local/Remote):
0 / 0
FEC Errors (Up/Down):
4.294.967.232 / 5
CRC Errors (Up/Down):
4.294.967.232 / 0
HEC Errors (Up/Down):
0 / 0

Create new topic
8035 posts

Uber Geek

Trusted

  # 262939 10-Oct-2009 00:17
Send private message

Are you on Orcon+, did you area get cabineted?

Mad Scientist
21329 posts

Uber Geek

Trusted
Lifetime subscriber

  # 262940 10-Oct-2009 00:19
Send private message

have you restarted your modem? unplug leave at least 1 min. reconnect power. may not work but worth a try.




Involuntary autocorrect in operation on mobile device. Apologies in advance.


 
 
 
 


18 posts

Geek


  # 262945 10-Oct-2009 01:15
Send private message

This could be do to poor wiring, you may need a service person check your wiring.
Check the wiring box outside, you may have a plug you can insert a phone into the
jack with, usually a test jack.

If it is an old house, it may need to be updated in wiring.

On DSL there is no way you should only connect at 56K.


I have an old ISA 56K modem I use for AOL here in America, with this I connect at
56,1400 so you have an problem there with wiring, this is my guess.

Good luck.

7199 posts

Uber Geek

Trusted
Subscriber

  # 262969 10-Oct-2009 08:41
Send private message

Hi, I assume by the Infineion vendor ID you are on Orcon+ (ie a LLU connection) is this correct, as its very important to sorting your problem.

Based on the stats you have been all over the place but very low sync I would suggest that you are in a cabinesited area and suffering from mid span injection issues.

It would be useful if you could tell us where you are (send me a PM if you sensibly dont want to put that up publically) street/town(or city) is all we need to know to establish if you are in a cabnetised location. you can check this at this site.

If this is the case, ie you are on an Orcon+ plan and in a cabinet area, then you would be advised to move back to a Telecom Wholesale plan (still with Orcon if you wish) and your speeds should return.

If you are not currently on a Orcon+ plan (not LLU connection) then purhaps you have some serious wiring issues or by mistake you have been left on the home exchange and not migrated to a cabinet, in which case midspan injection issues would arise again.

Other things to do are isolation tests to by pass as much house wiring as possible, this means disconnecting averything except the modem, but from what you have indicated you have done a reasonable level of this.

Cyril



7 posts

Wannabe Geek


  # 263016 10-Oct-2009 12:04
Send private message

Yeah i am on orcon+ From that map it looks like I am cabineted, FOR/A
Have PM my address to you.
I have restarted my modem and left it off for at least a min, as well as completely isolating the modem and having nothing else on any lines. The house is old, but the wiring internally looks ok with no corrosion. connection drops out lots, like the dsl link won't stay up for a day.
Sometimes it reconnects at around 5-6mb but it normally is very flakey.
At what stage does it become a internal fault? at the street or at the house? I am down a ROW so hoping it is not at the Street.

2192 posts

Uber Geek

Trusted
Subscriber

  # 263019 10-Oct-2009 12:08
Send private message

rendude what modem are you using? I'm on Orcon+ as well and was using a D-Link 502T modem which constantly disconnected (sometimes 10 times a day), so changed to a Dynalink (different chipset) and haven't had a single disconnection in two months.



7 posts

Wannabe Geek


  # 263020 10-Oct-2009 12:13
Send private message

Main modem is a Thompson, have also tried dlink 502t, and another dlink.... actually come to think of it, they all were from other isps... but i guess that should not matter.. although the thompson has telecom settings in the fw i guess, which i have not bothered to remove. But i may well go and buy another modem anyway, as i would like some n wireless :)


on another note, all of these modems worked flawlessly at my previous address

 
 
 
 


7199 posts

Uber Geek

Trusted
Subscriber

  # 263037 10-Oct-2009 13:27
Send private message

Hi, you currently are not going via a cabinet as those ones are not due till 2011, so your directly connected to the Exchange. My estimation is that your are just over 3km to the Exchange based on your actual location and assuming where the cables would most likely run. Therefore your attenuation of 44dB is reasonable and if all was good should be able to achieve 5-6Mb/s.

I would still be suspect of your house wiring, if you can disconnect at the demarc and connect your modem directly there is the only real isolation test. You mentioned in the PM some odd wiring in the demarc, purhaps a photo would be good.

You also may want to try getting your modem to only connect at ADSL1/G992.1

Cyril



7 posts

Wannabe Geek


  # 263080 10-Oct-2009 17:11
Send private message

ok, i have now plugged my modem straight into the demarc and now my modem is now living beneath my floor boards, thank god for wireless :P

odd wiring was not at the demarc, but at one of the jackpoints, it was using different colours, instead of red and white it was blue and white or something....

Anyway i have connected a bit faster... like 5mb/s and i will see how it goes to see if it makes a difference... if it does not, then i will be getting onto orcon again.

Cheers
Ren

2414 posts

Uber Geek

Lifetime subscriber

  # 263087 10-Oct-2009 17:40
Send private message

You probably had the modem plugged into a filtered phone outlet, i.e., are you sure you don't have a master splitter filter installed somewhere.




Spark FibreMAX using Mikrotik CCR1009-8G-1S-1S+. Apple TV 4, Apple TV 4K, iPad Air 1, iPhone 6s, VodaTV Gen 2. If it doesn't move then its data cabled.


7199 posts

Uber Geek

Trusted
Subscriber

  # 263092 10-Oct-2009 17:53
Send private message

If you plug it into a filtered socket they typically wont sync at all and show attenuation way aboe 44dB.

Cyril

22894 posts

Uber Geek

Trusted
Subscriber

  # 263110 10-Oct-2009 18:31
Send private message

Blue and white is the normal pairing for the first line, orange and black for the second, red and green are also used sometimes for the unfiltered dsl signal. Quite a departure from the old 3 wire colours but it makes sense I guess.




Richard rich.ms

7199 posts

Uber Geek

Trusted
Subscriber

  # 263114 10-Oct-2009 18:53
Send private message

Re run some cat5 from the demarc to where you want the modem and install a filter at the demarc, this way you will bypass all the old wiring issues.

Cyril



7 posts

Wannabe Geek


  # 264818 18-Oct-2009 14:01
Send private message

My connection has been a bit more stable, have now done as Cyril suggested and everything seems to be working fine. hopefully speeds will get better one day, but at least i have a pretty stable connection at the mo.. cheers for everyones help

Ren

Create new topic



Switch your broadband provider now - compare prices


Twitter and LinkedIn »



Follow us to receive Twitter updates when new discussions are posted in our forums:



Follow us to receive Twitter updates when news items and blogs are posted in our frontpage:



Follow us to receive Twitter updates when tech item prices are listed in our price comparison site:





News »

Netflix releases 21 Studio Ghibli works
Posted 22-Jan-2020 11:42


Vodafone integrates eSIM into device and wearable roadmap
Posted 17-Jan-2020 09:45


Do you need this camera app? Group investigates privacy implications
Posted 16-Jan-2020 03:30


JBL launches headphones range designed for gaming
Posted 13-Jan-2020 09:59


Withings introduces ScanWatch wearable combining ECG and sleep apnea detection
Posted 9-Jan-2020 18:34


NZ Police releases public app
Posted 8-Jan-2020 11:43


Suunto 7 combine sports and smart features on new smartwatch generation
Posted 7-Jan-2020 16:06


Intel brings innovation with technology spanning the cloud, network, edge and PC
Posted 7-Jan-2020 15:54


AMD announces high performance desktop and ultrathin laptop processors
Posted 7-Jan-2020 15:42


AMD unveils four new desktop and mobile GPUs including AMD Radeon RX 5600
Posted 7-Jan-2020 15:32


Consolidation in video streaming market with Spark selling Lightbox to Sky
Posted 19-Dec-2019 09:09


Intel introduces cryogenic control chip to enable quantum computers
Posted 10-Dec-2019 21:32


Vodafone 5G service live in four cities
Posted 10-Dec-2019 08:30


Samsung Galaxy Fold now available in New Zealand
Posted 6-Dec-2019 00:01


NZ company oDocs awarded US$ 100,000 Dubai World Expo grant
Posted 5-Dec-2019 16:00



Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.


Support Geekzone »

Our community of supporters help make Geekzone possible. Click the button below to join them.

Support Geezone on PressPatron



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.

Alternatively, you can receive a daily email with Geekzone updates.