Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.




5 posts

Wannabe Geek


Topic # 113964 3-Feb-2013 10:27
Send private message

Hi all, first of all apologies if this is not the right forum for this post - it's my first day.

I have a Samsung TV (model LA32D450G1M) which has suddenly lost all DTV channels and will no longer tune in any of them through the auto tuning (or manual) feature. Analogue is working and I can get a fuzzy picture through a few of the ATV channels.

I moved house yesterday, set up the TV with the digital aerial and it tuned in to most digital channels (except TV3 & Four) perfectly first time. I was watching the Sevens while waiting for Telstra to come and install broadband. Eventually Telstra came and installed broadband, and weirdly this is when the TV went wrong.

While the technician was installing the modem and router, the TV was on and I was in the other room and heard the TV sound go off. I thought he must have unplugged it to plug in the router, but when I came out the TV was still on and had the 'Weak or no signal' message displayed. I didn't think too much of it because at my last house this would happen sometimes and a tweak of the aerial position would fix it.

So anyway the technician left after setting up broadband successfully and I turned the TV off and went out. Later when I came back and turned it back on I discovered the DTV channels were all showing the 'Weak or no signal' message. I went into the menu and went through the auto-tuning function several times, with no joy. After a few times I noticed that the auto tuning is now only starting from channel 5, channels 1 thru 4 no longer even exist?

I used google to try and find a solution and ended up doing a factory reset on the TV, but the situation hasn't changed after that. So I'm hoping someone here might have had a similar problem and be able to point me in the right direction to getting my DTV channels back again!

Thanks in advance!

Create new topic
591 posts

Ultimate Geek
+1 received by user: 28

Trusted

  Reply # 754979 3-Feb-2013 10:34
Send private message

Sounds like you have /had a poor connection & he disturbed it, or pulled it out.
Check the antenna connection/s working back from the Tv



5 posts

Wannabe Geek


  Reply # 754981 3-Feb-2013 10:48
Send private message

Thanks, yeah I have tried unplugging the aerial from the TV and the wall. Also tried unplugging everything, moving the wifi router as far away from the TV/aerial as possible. But maybe I need to move the TV and aerial into a different part of the room. Will try that.

 
 
 
 


25815 posts

Uber Geek
+1 received by user: 5545

Moderator
Trusted
Biddle Corp
Lifetime subscriber

  Reply # 754985 3-Feb-2013 10:50
Send private message

The issue is clearly a signal related one. What type of aerial do you have are ane you using the correct connections?

6060 posts

Uber Geek
+1 received by user: 177

Trusted
Subscriber

  Reply # 754987 3-Feb-2013 10:53
Send private message

Yeah classic, you had an contractor in the house that was playing with................. RG6 feeds about the place, while he was there mysteriously one of thoses RG6 feeds to the TV looses connection. Obviously there could be numerous reasons why you would loose signal, but I think the culprit is obvious.......... no? Pity you never mentioned it at the time.

When I was doing antenna and cabling installation work I would always check other services before I left to confirm I had not un intentionally dropped something offline.

Edit, obviously I would only check related services (ie Telstra HFC and Sky etc) no other plumbing.

Cyril



5 posts

Wannabe Geek


  Reply # 754990 3-Feb-2013 11:01
Send private message

Thanks for your replies. I have moved the TV to another part of the room, as close to the outside world as possible and nothing's changed, the aerial is connected well and powered up, so I don't think it's a problem with that. Also that would not explain why DTV channels 1 thru 4 have dissapeared from the TV itself (e.g. they would still be there with 'weak signal' message if it was an aerial issue?).

I don't know anything about 'RG6 feeds' etc unfortunately, but it does seem like the Telstra broadband installation has something to do with the problem. I have tried unplugging the modem and router to see if that was interfering with the signal, without success. Is there something else I can do to check/fix that? Thanks.

I should also make clear that the aerial I'm using is a standalone 'rabbit ears' digital dick smith aerial and is not coming out of the wall anywhere, it is not connected to the broadband cabling in any way.

269 posts

Ultimate Geek
+1 received by user: 5


  Reply # 754995 3-Feb-2013 11:10
Send private message

You sure the TV is set to the correct input for the aerial?




Mark Ascroft
Wellington


42 posts

Geek
+1 received by user: 2


  Reply # 754996 3-Feb-2013 11:23
Send private message

Check you cabling again , you can even try an internal aerial temporarily



5 posts

Wannabe Geek


  Reply # 755001 3-Feb-2013 11:42
Send private message

The TV has only one source selection for TV (others are PC, HDMI, USB etc) which is selected. It used to start-up on 'DTV' channels and then move on to 'ATV' channels as you went through the channels with the remote. Now only 'ATV' channels are available. 

As stated previously I am using an internal 'rabbit ears' style digital aerial which was working fine up until yesterdays. It is not coming out of the wall or connected to the Broadband cabling in any way.

Thanks.

25815 posts

Uber Geek
+1 received by user: 5545

Moderator
Trusted
Biddle Corp
Lifetime subscriber

  Reply # 755019 3-Feb-2013 12:16
Send private message

One could conclude from that information that you're using an internal antenna and were very lucky to be getting a signal. I would pick that this antenna has now been moved which has caused the signal to be lost.

Internal antennas are really only any good in high signal areas, which presumably you're not in.

For Freeview|HD reception an exernal antenna is the recommended (and best) approach.

42 posts

Geek
+1 received by user: 2


  Reply # 755055 3-Feb-2013 13:30
Send private message

Use a digital approved internal Ariel with amplifier or use external arial as suggested by Biddle

1883 posts

Uber Geek
+1 received by user: 114


  Reply # 755056 3-Feb-2013 13:30
Send private message

SilentDesigns:
I should also make clear that the aerial I'm using is a standalone 'rabbit ears' digital dick smith aerial and is not coming out of the wall anywhere, it is not connected to the broadband cabling in any way.

That will be the problem.
Install an external antenna on the roof. Your antenna was barely able to provide a signal and now it doesn't. Just moving cabling about or installing more cable was enough to wipe out what signal it was getting.

6060 posts

Uber Geek
+1 received by user: 177

Trusted
Subscriber

  Reply # 755059 3-Feb-2013 13:42
Send private message

Its called the cliff effect, if you have a dodgy signal (that an indoor antenna will easily supply) then it can go from going to not going with only minor enviromental changes.

Cyril

1141 posts

Uber Geek
+1 received by user: 142


  Reply # 755064 3-Feb-2013 14:03
Send private message

yep.

this should have been a clue to all you digital sleuths...


...set up the TV with the digital aerial and it tuned in to most digital channels (except TV3 & Four) perfectly first time.



5 posts

Wannabe Geek


  Reply # 755110 3-Feb-2013 16:14
Send private message

Ok so the consensus seems to be that it's a case of getting an external aerial installed. I will contact the landlord and check that they are ok with that. Thanks for all responses, much appreciated!


6060 posts

Uber Geek
+1 received by user: 177

Trusted
Subscriber

  Reply # 755133 3-Feb-2013 17:36
Send private message

Try turning the Telstra cable modem off, just a thought

Cyril

Create new topic



Twitter »

Follow us to receive Twitter updates when new discussions are posted in our forums:



Follow us to receive Twitter updates when news items and blogs are posted in our frontpage:



Follow us to receive Twitter updates when tech item prices are listed in our price comparison site:





News »

$3.74 million for new electric vehicles in New Zealand
Posted 17-Jan-2018 11:27


Nova 2i: Value, not excitement from Huawei
Posted 17-Jan-2018 09:02


Less news in Facebook News Feed revamp
Posted 15-Jan-2018 13:15


Australian Government contract awarded to Datacom Connect
Posted 11-Jan-2018 08:37


Why New Zealand needs a chief technology officer
Posted 6-Jan-2018 13:59


Amazon release Silk Browser and Firefox for Fire TV
Posted 21-Dec-2017 13:42


New Chief Technology Officer role created
Posted 19-Dec-2017 22:18


All I want for Christmas is a new EV
Posted 19-Dec-2017 19:54


How clever is this: AI will create 2.3 million jobs by 2020
Posted 19-Dec-2017 19:52


NOW to deploy SD-WAN to regional councils
Posted 19-Dec-2017 19:46


Mobile market competition issues ComCom should watch
Posted 18-Dec-2017 10:52


New Zealand government to create digital advisory group
Posted 16-Dec-2017 08:47


Australia datum changes means whole country moving 1.8 metres north-east
Posted 16-Dec-2017 08:39


UAV Traffic Management Trial launching today in New Zealand
Posted 12-Dec-2017 16:06


UFB connections pass 460,000
Posted 11-Dec-2017 11:26



Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.

Alternatively, you can receive a daily email with Geekzone updates.