Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.




15 posts

Geek


Topic # 179352 5-Sep-2015 09:06
Send private message

I've been trawling through this board and the Snap board trying to find out if any snags were found with using a third party modem/router/modem+router on 2degrees. Has anyone managed?

I currently have an Asus AC66U and Draytek Vigor 120 (soon to be 130 for VDSL support for future proofing) and I bridge PPPOE authentication to PPPOA for my current Vodafone connection. On 2degrees I presume the same would be required, and if I did get VDSL the bridging wouldn't be required as I would have PPPOE authentication natively, correct?

Can anyone see any issues with my plan? I'm not keen to use the Fritz!box as I run VPNs on my current router and run MerlinWRT so I'm not willing to go to a stock set up.

View this topic in a long page with up to 500 replies per page Create new topic
 1 | 2
775 posts

Ultimate Geek
+1 received by user: 255

Trusted

  Reply # 1380117 5-Sep-2015 09:14
2 people support this post
Send private message

Can't see any issues. Snap/2degrees just require your username/password combination. If you're on VDSL or UFB it needs to be VLAN 10 tagged PPPoE. ADSL = PPPoA. If you're on EUBA you'll find you can use VLAN 10 tagged PPPoE as well.

I'm only using the Fritzbox to run the phone, still using my Asus router to terminate the PPP session and NF4V in bridge mode on VDSL.



15 posts

Geek


  Reply # 1380128 5-Sep-2015 09:29
Send private message

Lorenceo: Can't see any issues. Snap/2degrees just require your username/password combination. If you're on VDSL or UFB it needs to be VLAN 10 tagged PPPoE. ADSL = PPPoA. If you're on EUBA you'll find you can use VLAN 10 tagged PPPoE as well.

I'm only using the Fritzbox to run the phone, still using my Asus router to terminate the PPP session and NF4V in bridge mode on VDSL.


Thanks. Strange that I saw so many people asking if it was possible. I didn't think it would be an issue.

 
 
 
 


2081 posts

Uber Geek
+1 received by user: 329


  Reply # 1380287 5-Sep-2015 15:56
Send private message

On advice by GZ'ers I only needed to change name and password on my Spark supplied HG630b to get it up and running on 2D so no black magic required :P

64 posts

Master Geek
+1 received by user: 3


  Reply # 1390870 21-Sep-2015 07:41
Send private message

anyone try and get their 2 degrees broadband working on an orcon genius router(black). I have just signed up but my issues is the wifi range does not seem as good.
what 2 degrees settings do i have to use on the orcon genius router?


note for self: think there is 3 different routers on offer see this post.
FRITZ!Box 7360
and the higher specked 7490.
7390
edit: similar poor wifi experience int his post
edit: just have adsl and don't use voip or standard phone line.

6799 posts

Uber Geek
+1 received by user: 3132

Moderator
Trusted
Subscriber

  Reply # 1390872 21-Sep-2015 07:50
Send private message

I use an Edgerouter Lite with my UFB plan. It is rather easy to get a 3rd party router setup.

For VDSL/UFB you need VLAN Tagging (10) and PPPoE.




Michael Murphy | https://murfy.nz
Want to be with an epic ISP? Want $20 to join them too? Well, use this link to sign up to BigPipe!
The Router GuideCommunity UniFi Cloud Controller | Ubiquiti Edgerouter Tutorial


64 posts

Master Geek
+1 received by user: 3


  Reply # 1525592 4-Apr-2016 10:09
Send private message

so i finally tried to try using my genius broadband router (as I think the wifi is slightly better on it) instead of my fritzbox router supplied my 2degrees. The internet was working fine with my fritxbox, and then I swapped it with the genius router. The only changes I made on the genius router was to change the username from  x@orcon.co.nz to username@snap.co.nz and the password. There is probably other changes but I gave this ago, but I could not get connected to the internet. 

 

 

 

So then I tried to put the fritzbox back, I had not made any changes to it, but now it says it does not work. It says something about a failed dsl line test. There is the option to calibrate the fritz router with the phone line disconnected from the back of the router. I done this and it passed. There is then a line test you can do with the phone line put back in. This is coming back with a failure on the line at 2meters and 4meters  (2 different tests). This I find strange as the line should be unaffected?

 

 

 

Anyhow logged a fault with 2D and there is meant to be someone out in 24-48 hours to check the line from the exchange. 

 

 

 

Can anyone advise on this?

 

Can anyone advise exactly what settings I need to change on the genius router to be the same as the fritzbox router so I can get my 2degrees internet working through my genius broadband router? I do not have Voip or a landline with 2D just the internet.

132 posts

Master Geek
+1 received by user: 40


  Reply # 1525706 4-Apr-2016 11:13
Send private message

hattrick123: so i finally tried to try using my genius broadband router (as I think the wifi is slightly better on it) instead of my fritzbox router supplied my 2degrees. The internet was working fine with my fritxbox, and then I swapped it with the genius router. The only changes I made on the genius router was to change the username from  x@orcon.co.nz to username@snap.co.nz and the password. There is probably other changes but I gave this ago, but I could not get connected to the internet.    So then I tried to put the fritzbox back, I had not made any changes to it, but now it says it does not work. It says something about a failed dsl line test. There is the option to calibrate the fritz router with the phone line disconnected from the back of the router. I done this and it passed. There is then a line test you can do with the phone line put back in. This is coming back with a failure on the line at 2meters and 4meters  (2 different tests). This I find strange as the line should be unaffected?   Anyhow logged a fault with 2D and there is meant to be someone out in 24-48 hours to check the line from the exchange.    Can anyone advise on this? Can anyone advise exactly what settings I need to change on the genius router to be the same as the fritzbox router so I can get my 2degrees internet working through my genius broadband router? I do not have Voip or a landline with 2D just the internet.

 

 

 

the username should be @snap.net.nz


64 posts

Master Geek
+1 received by user: 3


  Reply # 1525711 4-Apr-2016 11:26
Send private message

tks I think i had that bit right, I was just working from memory on writing the question. I just copied the username from the fritzbox settings, I will double check. Also on the password that goes with this username, on the fritzbox is it 1234? I made that assumption but I have no way of confirming this.


775 posts

Ultimate Geek
+1 received by user: 255

Trusted

  Reply # 1526080 4-Apr-2016 23:16
Send private message

The password will be whatever you set up when you signed up. The same password you use to sign in to the account section on their website.


6 posts

Wannabe Geek
+1 received by user: 1


  Reply # 1526121 5-Apr-2016 02:04
Send private message

 call up and get them to configure your fritz and manually enter user/pass. If you're not getting dsl after that log a fault, if you logged a fault and it was just modem config you'll probably get a fee 


64 posts

Master Geek
+1 received by user: 3


  Reply # 1526162 5-Apr-2016 08:31
Send private message

I logged a fault on sun night but thought they could fix it over the phone, but after the usual checking a different cable, powering on and off, checking all jack points, they decided that someone had to be called out. Before ringing them i had done the following. There is the option to calibrate the fritz router with the phone line disconnected from the back of the router. I done this and it passed. There is then a line test you can do with the phone line put back in. This is coming back with a failure on the line at 2meters and 4meters  (2 different tests). This I find strange as the line should be unaffected?

 

 

 

 

 

They did go on about a 240$ fine if there was nothing wrong with the line, which i thought was interesting. 

 

they did also offer insurane @4$ in case i do find a line fault, istead of paying a possible 140$ fault fix fee if one is found. We will see how we go. 

 

 

 

Anyhow a tech was due to call out on tuesday morning but came yesterday and I missed a call from him. I got home and was told that he said the line was fine that either router should work. I just need to enter my username and password. So I tried this, but no joy I also tried the calibrate and dsl line test mentioned above again still no joy. I then started to ring them, and whilst doing some playing around, I then seen some other line diagnostic test that seemed to take longer and that seemed to fix it after a while(come back and edit with more detail). I was also connected to the router via a cable as opposed to the wifi, which I am not sure if that made a difference. Anyhow this seemed to get it working.  

 

 

Now can I do this with the genius router? regarding the username i have this right username@snap.co.nz. Regarding the password when I look at it on the fritzbox I just see 4 characters (****) so i thought it might be just 4 characters long, hence my assumption 1234. But my password for the 2degrees webpage is longer than 4 digits. Can anyone confirm if the password is the same for the router as it is for signing into their website? Maybe that is all i need to get right on the genius router?

 

 

 

Also the genius router was configed for voip so i am not sure if that would be an issue in gettting it working on 2D as some of the voip settings on the genius router look like they are hard set so I cannot change them.

Minimalist
5397 posts

Uber Geek
+1 received by user: 366

Moderator
Trusted
Subscriber

  Reply # 1526239 5-Apr-2016 11:28
Send private message

It is your full password as used on the website.

Minimalist
5397 posts

Uber Geek
+1 received by user: 366

Moderator
Trusted
Subscriber

  Reply # 1526241 5-Apr-2016 11:30
Send private message

Have you factory reset your FB and then plugged in? It should auto configure if you leave it for a few minutes.

64 posts

Master Geek
+1 received by user: 3


  Reply # 1526278 5-Apr-2016 12:07
Send private message

 I got the FB working, but out of curiosity how do you do a factory reset on it.  I could not see a button to do this.


Minimalist
5397 posts

Uber Geek
+1 received by user: 366

Moderator
Trusted
Subscriber

 1 | 2
View this topic in a long page with up to 500 replies per page Create new topic



Twitter »

Follow us to receive Twitter updates when new discussions are posted in our forums:



Follow us to receive Twitter updates when news items and blogs are posted in our frontpage:



Follow us to receive Twitter updates when tech item prices are listed in our price comparison site:





News »

UFB killer app: Speed
Posted 17-Nov-2017 17:01


The case for RSS — MacSparky
Posted 13-Nov-2017 14:35


WordPress and Indieweb: Take control of your online presence — 6:30 GridAKL Nov 30
Posted 11-Nov-2017 13:43


Chorus reveals technology upgrade for schools, students
Posted 10-Nov-2017 10:28


Vodafone says Internet of Things (IoT) crucial for digital transformation
Posted 10-Nov-2017 10:06


Police and Facebook launch AMBER Alerts system in NZ
Posted 9-Nov-2017 10:49


Amazon debuts Fire TV Stick Basic Edition in over 100 new countries
Posted 8-Nov-2017 05:34


Vodafone VoIP transition to start this month
Posted 7-Nov-2017 12:33


Spark enhances IoT network capability
Posted 7-Nov-2017 11:33


Vocus NZ sale and broadband competition
Posted 6-Nov-2017 14:36


Hawaiki reaches key milestone in landmark deep-sea fibre project
Posted 4-Nov-2017 13:53


Countdown launches new proximity online shopping app
Posted 4-Nov-2017 13:50


Nokia 3310 to be available through Spark New Zealand
Posted 4-Nov-2017 13:31


Nest launches in New Zealand
Posted 4-Nov-2017 12:31


Active wholesale as Chorus tackles wireless challenge
Posted 3-Nov-2017 10:55



Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.

Alternatively, you can receive a daily email with Geekzone updates.