Floating desk install

Forums › Home Workshop DIY › Floating desk install

33coupe

1029 posts

Uber Geek
+1 received by user: 78

ID Verified

#324894 9-Jun-2026 10:13

I've just received a quote of nearly $2k from builder/joinery company to install a desk in a small office. I'm sure this is something I can do, but just need a bit of advice on the technical side.

The room is 2.8m wide and wanting desk entire width for two persons. 800mm deep desk. There are 3 walls so I can install batons around there, but need something to support the middle (not a leg though).

I was originally thinking a big (or multiple) L brackets in the studs (behind gib) into desk.

Chatgpt suggests a horizontal support closer to edge of desk (with bracing like a deck), I'm not 100 sure how to execute this though.

Anyone have easy solutions to this please?

Thanks in advance

turtleattacks

1022 posts

Uber Geek
+1 received by user: 311

Trusted

#3501498 9-Jun-2026 10:59

Is it for aesthetics that you want it to be floating and without a leg?

----

Creator of whatsthesalary.com and whatstheincometax.com

Stu1

1937 posts

Uber Geek
+1 received by user: 509

ID Verified

Subscriber

#3501501 9-Jun-2026 11:09

I did something similar, I brought an old table from a charity shop cut it down to size. You can buy tops from Bunnings as well. We put support brackets around all three walls . We then attached a steel bar to the front of the desk for support . It’s been fantastic

eracode

Smpl Mnmlst
9467 posts

Uber Geek
+1 received by user: 6355

ID Verified

Trusted

Lifetime subscriber

#3501513 9-Jun-2026 12:30

@Stu1 's approach looks good. However 2.8m is a very long span - much longer than his. Would require a reasonably strong steel bar even though not a lot of weight is likely to be put on it. Bunnings sell steel angle - say 50x50mm - but not in lengths longer than 2m and it would probably need to be one piece for the full length.

I think your overall approach with the large L-brackets you mentioned would be fine.

Brackets something like this?

I know you don't want a leg but, sorry to second-guess, how about something like this set as far back towards the wall as possible, to reduce the optics of the leg? Or this smaller one?

Sometimes I just sit and think. Other times I just sit.

Stu1

1937 posts

Uber Geek
+1 received by user: 509

ID Verified

Subscriber

#3501516 9-Jun-2026 13:08

eracode:

@Stu1 's approach looks good. However 2.8m is a very long span - much longer than his. Would require a reasonably strong steel bar even though not a lot of weight is likely to be put on it. Bunnings sell steel angle - say 50x50mm - but not in lengths longer than 2m.

I think your overall approach with the large L-brackets you mentioned would be fine too.

Brackets something like this?

I know you don't want a leg but, sorry to second-guess, how about something like this set as far back towards the wall as possible? Or this smaller one?

prob do need a leg at the back for that length I’m lucky mine is for only me :)

eracode

Smpl Mnmlst
9467 posts

Uber Geek
+1 received by user: 6355

ID Verified

Trusted

Lifetime subscriber

#3501518 9-Jun-2026 13:11

Stu1:

eracode:

@Stu1 's approach looks good. However 2.8m is a very long span - much longer than his. Would require a reasonably strong steel bar even though not a lot of weight is likely to be put on it. Bunnings sell steel angle - say 50x50mm - but not in lengths longer than 2m.

I think your overall approach with the large L-brackets you mentioned would be fine too.

Brackets something like this?

I know you don't want a leg but, sorry to second-guess, how about something like this set as far back towards the wall as possible? Or this smaller one?

prob do need a leg at the back for that length I’m lucky mine is for only me :)

I was thinking more to support the front. He can put a horizontal support along the wall, screwed into studs, to support the rear edge.

Sometimes I just sit and think. Other times I just sit.

mdf

mdf
3571 posts

Uber Geek
+1 received by user: 1529

Trusted

Lifetime subscriber

#3501520 9-Jun-2026 13:38

2.8 m is a very wide span. Most off the shelf sheet goods will be smaller than that. So you have two potential issues:

You may need fixings to join board(s)
You need something to stop flexing/sagging in the middle of the span

As others have said, the easy answer is a leg(s) in the middle.

Failing that, you will need probably some kind of beam. You might be able to get away with a single bigger beam across the middle but I would probably aim for something front and back.

Brackets along the back wall might help with the sagging, but not joining boards. Addionally you potentially have some torque pushing down against the bracket (though that will be offset by the side mounting). Gib is relatively soft so your desk pushing down will end up compacting the gib, which may lead to wobble (and gib dents). Even then, you're going to need a pretty big bracket and most will probably have some kind of gusset (a diagonal support). And probably look quite industrial.

Given all that, personally I'd be inclined to just go with the easy answer and put a discrete leg or dividing board in. Or drawers in the middle that take the weight?

Or lean into it and make it a feature: have two sit stand desks next to each other? I love my sit stand and would never go back.

Quic Broadband

Move to New Zealand's best fibre broadband service (affiliate link). Free setup code: R587125ERQ6VE. Note that to use Quic Broadband you must be comfortable with configuring your own router.

wellygary

8940 posts

Uber Geek
+1 received by user: 5485

#3501524 9-Jun-2026 14:17

eracode:

@Stu1 's approach looks good. However 2.8m is a very long span - much longer than his. Would require a reasonably strong steel bar even though not a lot of weight is likely to be put on it. Bunnings sell steel angle - say 50x50mm - but not in lengths longer than 2m and it would probably need to be one piece for the full length.

Mitre 10 do "metal mate" tubes @2.4m.. so its getting closer,

https://www.mitre10.co.nz/shop/metal-mate-galvanised-steel-square-tube-25-4x25-4x1-6mm-x-2-4m-silver/p/372592

If you ran two wooden beams across the diagonal from the front corners towards the back wall you could then mount the steel beam between them .. It would be 200mm from the front of the desk, which is probably fine unless you are dancing on the front edge of it...

mdooher

Hmm, what to write...
1455 posts

Uber Geek
+1 received by user: 918

ID Verified

Trusted

Lifetime subscriber

#3501574 9-Jun-2026 14:39

this is 65x35 heavy wall steel. Note there are welded brackets bolted into the wall hidden behind the wooden cleat. This is only 2m across and holds my wife's sewing machine and overlocker. it works well.

I would think at 2.8m you would need to put the steel the other way up (watch your knees) unless you use nonflexible glue on top of the beam. This will put the wooden top in compression when weight is applied preventing it from bending.

i.e. use physics not brute force to hold it up.

Matthew

Stu1

1937 posts

Uber Geek
+1 received by user: 509

ID Verified

Subscriber

#3501587 9-Jun-2026 16:35

mdooher:

this is 65x35 heavy wall steel. Note there are welded brackets bolted into the wall hidden behind the wooden cleat. This is only 2m across and holds my wife's sewing machine and overlocker. it works well.

I would think at 2.8m you would need to put the steel the other way up (watch your knees) unless you use nonflexible glue on top of the beam. This will put the wooden top in compression when weight is applied preventing it from bending.

i.e. use physics not brute force to hold it up.

That looks really good , nice job 👍

33coupe

1029 posts

Uber Geek
+1 received by user: 78

ID Verified

#3501588 9-Jun-2026 16:41

Thanks for the replies, some great knowledge and ideas / examples given. I was hoping to get away with just l shaped brackets & batons, but a support beam across the front middle would provide good support/ reassurance.

I did find some heavy duty brackets 600mm long which look pretty robust (not cheap though) https://www.visualhardware.co.nz/shop/product/724384/utilitarian-heavy-duty-stayed-bracket-3-sizes/?variantId=3943807