Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.


outdoorsnz

694 posts

Ultimate Geek
+1 received by user: 303

ID Verified

#298832 20-Jul-2022 11:15
Send private message

With all the recent heavy rain discovered a small leak in my spare bathroom.

 

I knew my roof needed a bit of work to clean up as the cold side covered in quite a bit of lichen, but was surprised when rain exposed 3 or 4 spots that have rusted pretty bad. Have lived in new place for 8 months and first time it has really rained!

 

Where the two sheets overlap, ridges have rusted through. Only one hole had rusted right through, hence the leak. Was where it was nailed, so the leak spread along about half a meter.

 

Longer term I will need to replace the sheets in bad condition. But plan is to chemical treat the roof to kill all moss / lichen (maybe a few treatments), fix rust / replace sheets and then paint.

 

Also suspect there is a very small leak on old aerial wire stay as quite loose (different location). Which will need to be remove and will leave a nail size hole.

 

Have done what any self respecting DIY hacker would do and filled everything with silicone as a short term fix to stop the water getting in!

 

My question is: What is the best method to fix holes in the roof?

 

My local bunnings store suggested Denso Tape. But I got confused on that as youtube etc suggested it was more suitable for pipe lagging. Someone else suggested a bitumen type paint on product.

 

Thanks


Create new topic
Bung
6733 posts

Uber Geek
+1 received by user: 2926

Subscriber

  #2944154 20-Jul-2022 11:39
Send private message

What sort of pitch is there on the roof? If you have reasonable slope you might be able to put a "slip" under the hole as a temporary measure. Take out as many nails/screws as you have to and slide a piece of corrugated iron under the hole. Put screws back.



outdoorsnz

694 posts

Ultimate Geek
+1 received by user: 303

ID Verified

  #2944165 20-Jul-2022 11:54
Send private message

Bung: What sort of pitch is there on the roof? If you have reasonable slope you might be able to put a "slip" under the hole as a temporary measure. Take out as many nails/screws as you have to and slide a piece of corrugated iron under the hole. Put screws back.

 

Not sure of the degrees. How would you measure that? But I think you would describe it as a reasonable pitch. Def not flat. You can safely walk on it with care, but I wouldn't go near the edges or when it is wet!

 

I do have a off cut lying around that could be cut up into sections.

 

The roof also needs to re-screwed to replace the lead heads.


duckDecoy
946 posts

Ultimate Geek
+1 received by user: 432

Subscriber

  #2944167 20-Jul-2022 11:58
Send private message

Read through this thread to get some more info on what to do.

 

https://www.geekzone.co.nz/forums.asp?forumId=141&topicId=295786

 

 




Bung
6733 posts

Uber Geek
+1 received by user: 2926

Subscriber

  #2944172 20-Jul-2022 12:04
Send private message

If the roof is too flat the water might not drain down the patch. Yours sounds OK. Ideally you want to got from purlin above hole down to edge. Be realistic about repairs you're just delaying the inevitable.

timmmay
20858 posts

Uber Geek
+1 received by user: 5350

Trusted
Lifetime subscriber

  #2944175 20-Jul-2022 12:09
Send private message

I'd replace any sheets that are rusty at all. Sounds like it might be time for a complete re-roof. It got more expensive a while back when roofing contractors have to use more safety equipment, but what I find is they charge for it (scaffolding or some system to attach them to the roof) then don't actually order / use it so they make more money.


outdoorsnz

694 posts

Ultimate Geek
+1 received by user: 303

ID Verified

  #2944194 20-Jul-2022 12:43
Send private message

duckDecoy:

 

Read through this thread to get some more info on what to do.

 

https://www.geekzone.co.nz/forums.asp?forumId=141&topicId=295786

 

 

Thanks. Some good pointers in that.


 
 
 
 

Shop now on Samsung phones, tablets, TVs and more (affiliate link).
outdoorsnz

694 posts

Ultimate Geek
+1 received by user: 303

ID Verified

  #2944195 20-Jul-2022 12:49
Send private message

Bung: If the roof is too flat the water might not drain down the patch. Yours sounds OK. Ideally you want to got from purlin above hole down to edge. Be realistic about repairs you're just delaying the inevitable.

 

Absolutely agree. Apart from the lead heads, which I already have replacement screws with wide flanges to cover holes, and the rusted bits, the rest is in OK condition.

 

The issues have resulted from the cold side of the house, trees that drop stuff every where and hasn't been cleaned / maintained.

 

Temp repairs now and sort when the weather gets better. North of Dunedin. Weather has been wet and cold!


rscole86
4999 posts

Uber Geek
+1 received by user: 462

Moderator
Trusted
Lifetime subscriber

  #2944203 20-Jul-2022 13:21
Send private message

I've seen Epar used on minor roof repairs, not sure if it's available to consumers or a trade product?

It looks like it's a multipurpose epoxy paste, so I assume the big box retailers would have something similar.

GGJohnstone
86 posts

Master Geek
+1 received by user: 5


  #2944425 20-Jul-2022 19:18
Send private message

Paint on a cloth patch with ordinary roof paint. Could last for years.


SepticSceptic
2263 posts

Uber Geek
+1 received by user: 779

Trusted

  #2944576 20-Jul-2022 23:07
Send private message

Bitumen tape could be a starter

https://www.mitre10.co.nz/shop/sika-multiseal-self-adhesive-bituminous-sealing-tape-150mm-x-10m-grey/p/360227

Sidestep
1019 posts

Uber Geek
+1 received by user: 567

Lifetime subscriber

  #2944601 21-Jul-2022 04:17
Send private message

We asphalt-glued industrial grade aluminium foil all over a rusted corrugated roof on a shed/barn - and painted over it (just to hide the glare).
It was exposed to the open ocean and - like yours - had rusted badly under flashings, along sheet overlaps, drip edges and where neoprene seals had shrunk/disappeared from Tek screws.

 

It cost very little, and worked well - though was supposed to be temporary.
The Regional Council had declared a chunk of our property 'Outstanding Landscape Feature' and was trying to force us to demolish buildings that were on the skyline/visible from the water.

 

Six years later they gave up and we properly re-roofed the building with colorsteel.
The original leak issues had been so bad that the galvanised diagonal strap bracing underneath had all come loose - the nail heads had rusted off or pulled through the strapping.

 

Our repairs were basically intact (though a couple of new holes had appeared, and there was wind damage where fixings had pulled through rusted sheets).
The shed - tractors, trailer boat etc. parked inside - had stayed dry all that time.

 

I reckon it was a pretty good effort, the foil was easy to shape over edges, ridges & fixings - just had to wirebrush the rust back.
We did chuck some spare phosphoric acid on the worst bits.


Create new topic








Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.