AV faceplates

Forums › Home Theatre (including HTPC and EPG Collector) › AV faceplates

pjays

109 posts

Master Geek

#137968 15-Dec-2013 10:42

Hi

I have looking into AV faceplates ... the customisable keystone ones seem ideal as I can set up exactly how I want.

But I have found nothing yet that supports all of HDMI, aerial connection, CAT6 and USB and composite plugs. Some have most of these but are missing one or two.

I was trying to do this all with a single faceplate but that does not seem possible?

On a related topic - I have bought a length of CAT6 cable to run .. it has connectors at each end... but, all the faceplate jacks that I can see seem to require wiring into the back of the plug, I was expecting to be able to just clip in on the back. I really don't want to have to cut these cables and wire them into the plugs.

overkill

222 posts

Master Geek

#952487 15-Dec-2013 11:13

Check out the following guys from Christchurch, great service, great product and really great prices.

http://www.darkstar.co.nz/wall-plates.html

They should have all you need to be able to populate a single plate, including the Cat5/6 modular joiner so you can plug your Cat cable in on one side of the wall plate.

"Setting the Standard in Quality and Commitment"

berrys

225 posts

Master Geek

#952488 15-Dec-2013 11:14

If the faceplate is not seen, perhaps one of these first 3 listed:

http://www.rapalloav.co.nz/catalogsearch/result/?q=feed+through+wall+plate

Then you don't have to worry about wiring and signal quality loss (if any). Not sure if this is the best price, but a starting point.

berrys

225 posts

Master Geek

#952489 15-Dec-2013 11:16

overkill: Check out the following guys from Christchurch, great service, great product and really great prices.

http://www.darkstar.co.nz/wall-plates.html

They should have all you need to be able to populate a single plate, including the Cat5/6 modular joiner so you can plug your Cat cable in on one side of the wall plate.

Great link - thanks!

DarthKermit

5346 posts

Uber Geek

Trusted

#952492 15-Dec-2013 11:26

The PDL Modena range has modules for all that you asked for. PDL 600 series has them all, except for a USB connector.

Whatifthespacekeyhadneverbeeninvented?

overkill

222 posts

Master Geek

#952613 15-Dec-2013 17:25

DarthKermit: The PDL Modena range has modules for all that you asked for. PDL 600 series has them all, except for a USB connector.

The biggest problem with the Modena range is you are limited to x3 modules per faceplate, with the 600 series you can get x6 individual modules per faceplate and you can get USB modules for the PDL, just not made by Schneider.

"Setting the Standard in Quality and Commitment"

DarthKermit

5346 posts

Uber Geek

Trusted

#952628 15-Dec-2013 18:03

overkill: [you can get USB modules for the PDL, just not made by Schneider.

I didn't know that. Who supplies them?

Whatifthespacekeyhadneverbeeninvented?

overkill

222 posts

Master Geek

#953298 16-Dec-2013 20:00

DarthKermit:
overkill: [you can get USB modules for the PDL, just not made by Schneider.

I didn't know that. Who supplies them?

Check out the following link, it's one I found, but I use the USB modules from Darkstar and then use PDL mech adapters from WiredNZ (you can get the whole unit from WiredNZ also)....

http://www.patsbargains.co.nz/index.php?main_page=product_info&cPath=19&products_id=160

"Setting the Standard in Quality and Commitment"

Equinox IT

Cloud spending continues to surge globally, but most organisations haven’t made the changes necessary to maximise the value and cost-efficiency benefits of their cloud investments. Download the whitepaper From Overspend to Advantage now.

JWR

821 posts

Ultimate Geek

#953478 17-Dec-2013 08:23

overkill: Check out the following guys from Christchurch, great service, great product and really great prices.

http://www.darkstar.co.nz/wall-plates.html

They should have all you need to be able to populate a single plate, including the Cat5/6 modular joiner so you can plug your Cat cable in on one side of the wall plate.

Thanks for that link.

I actually visited them and ended up buying quite a few things (roll cat6, tools etc..).

Like you said, good service and prices.

Cheers.