VoIP Trixbox installation

Forums › VoIP › VoIP Trixbox installation

AllNightNerding

411 posts

Ultimate Geek

Topic # 22771 7-Jun-2008 21:06

So Ellipsis and I have decided to spend a boring, rainy Saturday night installing Trixbox onto a spare PC of mine.

We have installed it according to tony's guidelines, "http://myasterisk.co.nz/2007/12/12/how-to-set-up-a-worldxchange-vfx-trunk-in-trixbox-22/"

We can communicate between the phones.

we have edited the bits that need editing pproperly (we think)

But when we try to make an outgoing call, we get the error "All circuits are busy right now, please try again later"

When we try to call it from an outside line we get the error "The number you are trying to reach is unavailable and can not take your call at this time, please leave a message"

Does anyone know how to fix this?

Thanks
Simon and Riley. :D

-- Divett Enterprises -- The Power Of Tomorrow --

Filterer

482 posts

Ultimate Geek
+1 received by user: 5

Reply # 136313 7-Jun-2008 22:07

Sounds like either your trunk has not registered or your inbound and outbound routes aren't setup properly.

If you have followed tonys guide then id suggest its the first of these two. If you login to the web portal under and go to the PBX settings page you should see the following

You want to be looking at IP Trunk Registrations - if this isn't at 1, then you will need to check out your vfx settings - perhpas turn on trixbox debug mode

AllNightNerding

411 posts

Ultimate Geek

Reply # 136330 7-Jun-2008 23:29

The IP trunk, and IP registrations, are both at 1.

how do you get into debug mode?

also, when logging into it, (the trixbox website logon to get updates) that doesnt appear to work. We have signed up and done all that stuff for the Trixbox website.

-- Divett Enterprises -- The Power Of Tomorrow --

sbiddle

25194 posts

Uber Geek
+1 received by user: 5040

Moderator

Trusted

Biddle Corp

Subscriber

Reply # 136346 8-Jun-2008 02:04

Try putting

disallow=all

at the start of your trunk settings rather than after the allow= statement, this should fix your issue. Something seems to have changed that requires the disallow statement before the allow, this never used to be the case.

AllNightNerding

411 posts

Ultimate Geek

Reply # 136348 8-Jun-2008 02:19

Come on! How simple do you have to get!

well I guess that now makes up for our lack of caffeine for the night (why didnt mum go shopping today...) it works!

-- Divett Enterprises -- The Power Of Tomorrow --

AllNightNerding

411 posts

Ultimate Geek

Reply # 136350 8-Jun-2008 02:48

Next minor technical issue......

When in the admin switched mode, we try to log into the asterisk website, (top right) but it just modifys it, to look like this:

<IMGhttp://divett.com/admin%20login.jpg>

-- Divett Enterprises -- The Power Of Tomorrow --

sbiddle

25194 posts

Uber Geek
+1 received by user: 5040

Moderator

Trusted

Biddle Corp

Subscriber

Reply # 136376 8-Jun-2008 10:44

Is this the trixbox login screen on the main dashboard?

Try a

yum -update

and that should update all the packages including the tbm-GUIcore which controls the main dashboard and menus

AllNightNerding

411 posts

Ultimate Geek

Reply # 136407 8-Jun-2008 12:16

tryed the yum -update, but it says there is no such command as u

but tryed a yum -y update, and that seems to be working and updating, and we can now log into it. Yah!

-- Divett Enterprises -- The Power Of Tomorrow --

sbiddle

25194 posts

Uber Geek
+1 received by user: 5040

Moderator

Trusted

Biddle Corp

Subscriber

Reply # 136409 8-Jun-2008 12:23

Oops my original post should have been "yum update"