What's inside fibre conduit

Forums › New Zealand Broadband › What's inside fibre conduit

eXDee

4025 posts

Uber Geek
+1 received by user: 1076

Trusted

# 138591 9-Jan-2014 21:14

From ultrafast fibre anyway!
https://www.dropbox.com/sc/hb5vkme3imwv9zw/cqNX41pOsP#/

This is near where i expect a FDH to go in, but i thought it was interesting that the conduit was split/cut into.

1 | 2

3190 posts

Uber Geek
+1 received by user: 415

# 964150 9-Jan-2014 21:16

Whoops. They yanked on that a little too hard when it was bent the wrong way

Downhillnz

62 posts

Master Geek
+1 received by user: 6

# 964163 9-Jan-2014 21:59

And the Ericsson Ribbonet. For all those Chorus areas

Coil

6615 posts

Uber Geek
+1 received by user: 2293
Inactive user

# 964203 9-Jan-2014 23:36

Those are what they blow the fibre through to the end user, Each one of those clear tubes will carry optical fibres to say 1 street and go all the way back to the exchange.

eXDee

4025 posts

Uber Geek
+1 received by user: 1076

Trusted

# 964214 9-Jan-2014 23:48

I'm under the impression they go back to a Fibre Distribution Hub, into an optical splitter/prism and then go back to the exchange? At least thats my understanding for GPON's basic system.

Batman

Mad Scientist
20336 posts

Uber Geek
+1 received by user: 2770

Trusted

Lifetime subscriber

# 964216 9-Jan-2014 23:54

how do they blow fibre into the straws?

Swype on iOS is detrimental to accurate typing. Apologies in advance.

Coil

6615 posts

Uber Geek
+1 received by user: 2293
Inactive user

# 964217 9-Jan-2014 23:54

Little green box on street i believe is where the local fibres terminate. From there its back to the exchange on a backhaul? Similar to how a cabinet works i think. Each network would vary of course but from Wikipedia it reckons that.

Coil

6615 posts

Uber Geek
+1 received by user: 2293
Inactive user

# 964219 9-Jan-2014 23:58

joker97: how do they blow fibre into the straws?

One end would probably be open if they use pressure to blow it. Unless they use these: https://www.youtube.com/watch?v=q8YH5E-8KUs

Oblivian

3190 posts

Uber Geek
+1 received by user: 415

# 964220 10-Jan-2014 00:00

Yeah that. Little caps fit onto the end of them, other end goes in a compressor

Batman

Mad Scientist
20336 posts

Uber Geek
+1 received by user: 2770

Trusted

Lifetime subscriber

# 964227 10-Jan-2014 01:01

TimA:
joker97: how do they blow fibre into the straws?

One end would probably be open if they use pressure to blow it. Unless they use these: https://www.youtube.com/watch?v=q8YH5E-8KUs

Wow what a sight to behold!

Swype on iOS is detrimental to accurate typing. Apologies in advance.

InstallerUFB

829 posts

Ultimate Geek
+1 received by user: 218

# 964248 10-Jan-2014 06:11

eXDee: From ultrafast fibre anyway!
https://www.dropbox.com/sc/hb5vkme3imwv9zw/cqNX41pOsP#/

This is near where i expect a FDH to go in, but i thought it was interesting that the conduit was split/cut into.

yep those are damaged and will be cut away when joined through or terminated

InstallerUFB

829 posts

Ultimate Geek
+1 received by user: 218

# 964250 10-Jan-2014 06:25

TimA:
joker97: how do they blow fibre into the straws?

One end would probably be open if they use pressure to blow it. Unless they use these: https://www.youtube.com/watch?v=q8YH5E-8KUs

That video is of a Micronet Blowing tool - that is the one that is used to 'blow' the larger size blown fibre cables (48 fibres up) through te bigger tubes - 11mm + / Between Exchanges, Commercial sites, Cabinet or FAT sites etc / One of the larger tubes is in the middle of the 26way in the photo, already added to this thread, and can be seen already joined in the middle of the smaller tubes

THe 'blowing gun' for the smaller tubeing (3 -8mm) looks more like a cordless drill/packing tape gun combination - This video shows an older model http://www.youtube.com/watch?v=NMFvTFOn-HA

wired

134 posts

Master Geek
+1 received by user: 37

# 964255 10-Jan-2014 08:00

eXDee: I'm under the impression they go back to a Fibre Distribution Hub, into an optical splitter/prism and then go back to the exchange? At least thats my understanding for GPON's basic system.

I agree. The photos show tubes about 3.5mm across so they are the tubes that are used into each premises from the roadside cabinet. The tubes that go back to the exchange from the cabinet are larger, about 10mm in diameter.

They can blow a 12 fibre cable into one of the small tubes and a 144 fibre cable into the larger tubes.