Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.
Forums › Home Workshop DIY › Pls help me with re-wiring my security alarm...


1449 posts

Uber Geek
+1 received by user: 317

Subscriber

Topic # 203139 19-Sep-2016 14:19
Send private message

Due to ongoing issues with my landline since getting fibre I need to disconnect my security alarm from the phone line.

 

The security guy says  "The best way to disconnect the monitoring is to join the IN and OUT wiring together in the control panel, as this will eliminate the alarm system from the phone line all together!"

 

 

The above is a photo of two wire blocks with TELCO LINE written underneath. I presume one is IN and one is OUT and it matters not which is which.

 

What I need to know is do I join...

 

(white1 - white2) and (brown - blue)?

 

or...

 

(white2 - blue) and (white1 to brown)?

 

or...

 

(white1 - blue) and (white2 - brown)?

 

To actually do the joining, I unscrew each wire from the block then just twisty them together in mid-air?

 

Any help greatly appreciated.




Life is too short to remove USB safely.

Create new topic
cisconz
1191 posts

Uber Geek
+1 received by user: 78

Trusted
Lifetime subscriber

  Reply # 1635892 19-Sep-2016 14:31
Send private message

To remove it to test, then twisting in mid air will be fine (Test only)

 

White to white, Blue to Brown

 

To bypass permanently - Use 2 Scotch lock connectors (Less than $1 each from an electrical wholesaler with no account)

 

To just stop it grabbing the line, but still allow it to communicate, connect Brown to Blue and into the Blue hole, then same for White in the Left hand White hole.

 

Basically, what the alarm does when it tries to communicate is disconnects the Brown and White from the circuit, makes it's call to the monitoring station, then connects it all back up again.




Hmmmm

cisconz
1191 posts

Uber Geek
+1 received by user: 78

Trusted
Lifetime subscriber

  Reply # 1635894 19-Sep-2016 14:32
Send private message

Scotch locks are these

 




Hmmmm

27140 posts

Uber Geek
+1 received by user: 6579

Moderator
Trusted
Biddle Corp
Lifetime subscriber

  Reply # 1635897 19-Sep-2016 14:35
Send private message

You simply want to join the brown+blue together and blue/white and brown/white together.

 

 



1449 posts

Uber Geek
+1 received by user: 317

Subscriber

  Reply # 1635902 19-Sep-2016 14:45
Send private message

Thanks. If I need them disconnected permanently I'll get the security guy to do it, as he will have to install an IP or cellular module instead so we can keep it monitored.

 

 




Life is too short to remove USB safely.

Stu

Hammered
5083 posts

Uber Geek
+1 received by user: 1071

Moderator
Trusted
Lifetime subscriber

  Reply # 1635903 19-Sep-2016 14:50
One person supports this post
Send private message

Of course the alarm will probably keep annoying you with comms failure alerts if you don't disable communication in the alarm settings after removing the phone line.




Keep calm, and carry on posting.

 

 

 

Click to see full size Click to see full size

544 posts

Ultimate Geek
+1 received by user: 127

Subscriber

  Reply # 1635906 19-Sep-2016 14:52
One person supports this post
Send private message

If you just want to bypass it temporarily and don't have any connectors handy you could just move the brown+white over and piggy back them on top of the brown+white (brown on top of blue, which on top of white). A bit more reliable than twisting them.

 

EDIT: brown not red

1604 posts

Uber Geek
+1 received by user: 333

Lifetime subscriber

  Reply # 1635907 19-Sep-2016 14:52
Send private message

kiwifidget:

 

Thanks. If I need them disconnected permanently I'll get the security guy to do it, as he will have to install an IP or cellular module instead so we can keep it monitored.

 

 

 

 

 

 

keeping in mind once you have removed the wiring from the terminals you will more than likely have a "line fault" come up on the keypad. Once the IP module is installed it should go away

 

 

 

 



1449 posts

Uber Geek
+1 received by user: 317

Subscriber

  Reply # 1635909 19-Sep-2016 14:56
Send private message

I dont think anything happens at the house. Initially we had no phone at all and we didn't get any alarms. The security company did but they didn't bother to let us know.

 

Its going to do a scheduled dial out at 3pm, so I'll disconnect after that. 




Life is too short to remove USB safely.



1449 posts

Uber Geek
+1 received by user: 317

Subscriber

  Reply # 1635910 19-Sep-2016 14:59
Send private message

solutionz:

 

If you just want to bypass it temporarily and don't have any connectors handy you could just move the red+white over and piggy back them on top of the red+white (red on top of blue, which on top of white). A bit more reliable than twisting them.

 

 

What red wires?




Life is too short to remove USB safely.

544 posts

Ultimate Geek
+1 received by user: 127

Subscriber

  Reply # 1635927 19-Sep-2016 15:19
Send private message

kiwifidget:

 

solutionz:

 

If you just want to bypass it temporarily and don't have any connectors handy you could just move the red+white over and piggy back them on top of the red+white (red on top of blue, which on top of white). A bit more reliable than twisting them.

 

 

What red wires?

 

 

*brown



1449 posts

Uber Geek
+1 received by user: 317

Subscriber

  Reply # 1636858 20-Sep-2016 21:01
Send private message

Thanks everyone. Mission accomplished. My alarm is not causing my phone problems in case you've been losing sleep wondering how I got on.




Life is too short to remove USB safely.

5275 posts

Uber Geek
+1 received by user: 2290

Trusted
Lifetime subscriber

  Reply # 1636878 20-Sep-2016 21:34
Send private message

Sorry I haven't replied to your email from last week. I was going to suggest patch from the phone port on the Huawei router through the patch panel directly to one phone only. Run that for a couple of days and see if phone issue persists.




Chorus has spent $1.4 billion on making their xDSL broadband network faster. If your still stuck on ADSL or VDSL, why not spend from $150 on a master filter install to make sure you are getting the most out of your connection?
I install - Naked DSL, DSL Master Splitters, VoIP, data cabling and general computer support for home and small business.
Rural Broadband RBI installer for Ultimate Broadband and Full Flavour

 

Need help in Auckland, Waikato or BoP? Click my email button, or email me direct: [my user name] at geekzonemail dot com



1449 posts

Uber Geek
+1 received by user: 317

Subscriber

  Reply # 1636930 20-Sep-2016 22:26
Send private message

coffeebaron: Sorry I haven't replied to your email from last week. I was going to suggest patch from the phone port on the Huawei router through the patch panel directly to one phone only. Run that for a couple of days and see if phone issue persists.

 

Hi Fraser, I tried patching just one phone directly into the router but the issue remained.

 

I've now eliminated the MySky, alarm, and Suresignal as causes. This just leaves the router, VF are sending me a new one to swap out. 




Life is too short to remove USB safely.

Create new topic

Twitter »

Follow us to receive Twitter updates when new discussions are posted in our forums:



Follow us to receive Twitter updates when news items and blogs are posted in our frontpage:



Follow us to receive Twitter updates when tech item prices are listed in our price comparison site:



Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.


Updates »

Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.

Alternatively, you can receive a daily email with Geekzone updates.