Cisco SR520-W problem!

Forums › Spark New Zealand › Cisco SR520-W problem!

Htech20

16 posts

Geek

Topic # 133516 24-Oct-2013 22:00

Hi Guys

I have a Cisco SR520-W Router that is just sitting on my desk at home. I currently have a TG585 v7 Thompson Router and am connected with Telecom ADSL and I need help if anyone knows how to connect my Cisco up to the Internet, as I have tried multiple times.

thanks

1 | 2

695 posts

Ultimate Geek
+1 received by user: 244

Trusted

Spark NZ

Reply # 921244 24-Oct-2013 23:06

What does your debug say?

My views are my own, and may not necessarily represent those of my employer.

sbiddle

27572 posts

Uber Geek
+1 received by user: 7032

Moderator

Trusted

Biddle Corp

Lifetime subscriber

Reply # 921354 25-Oct-2013 06:27

Need a lot more information - including what model do you have and how are you trying to connect it.

I assume you mean SRP520 which isn't actually a model - it's a range that covers multiple models of which the SRP521W and SRP527W are the two most common in this part of the world.

Htech20

16 posts

Geek

Reply # 921380 25-Oct-2013 08:35

Hi sbiddle

I do mean the SR520w

see link below

http://www.telephonyware.com/telephonyware/products/cisco-sr520w-fe-k9.html

I have that router sitting on my desk at home, have you worked with any of these?

BinaryLimited

791 posts

Ultimate Geek
+1 received by user: 79

Trusted

Reply # 921386 25-Oct-2013 08:47

Htech20: Hi sbiddle

I do mean the SR520w

see link below

http://www.telephonyware.com/telephonyware/products/cisco-sr520w-fe-k9.html

I have that router sitting on my desk at home, have you worked with any of these?

hi Htech

Are you looking looking for a default config file to upload?

Binary Limited - Safe. Secure. Simple. ™
www.binarylimited.co.nz

Htech20

16 posts

Geek

Reply # 921388 25-Oct-2013 08:56

yea if anyone knows a simple config, or I will have a look later on when I finish work, and use the debug command as I am not 100% sure what the issue is yet.

Inphinity

2532 posts

Uber Geek
+1 received by user: 940

Subscriber

Reply # 921391 25-Oct-2013 09:02

I'm a little confused what the question is. You can just connect the WAN port on the SR520W to a LAN port on the TG585, assign the WAN port a relevant IP and netmask, set the TG585s LAN address as the gateway, then set your required rules on the SR520W.

BinaryLimited

791 posts

Ultimate Geek
+1 received by user: 79

Trusted

Reply # 921392 25-Oct-2013 09:04

Inphinity: I'm a little confused what the question is. You can just connect the WAN port on the SR520W to a LAN port on the TG585, assign the WAN port a relevant IP and netmask, set the TG585s LAN address as the gateway, then set your required rules on the SR520W.

i think he wants to replace the thompson with the cisco, could be wrong tho?

Binary Limited - Safe. Secure. Simple. ™
www.binarylimited.co.nz

Inphinity

2532 posts

Uber Geek
+1 received by user: 940

Subscriber

Reply # 921404 25-Oct-2013 09:16

BinaryLimited:
Inphinity: I'm a little confused what the question is. You can just connect the WAN port on the SR520W to a LAN port on the TG585, assign the WAN port a relevant IP and netmask, set the TG585s LAN address as the gateway, then set your required rules on the SR520W.

i think he wants to replace the thompson with the cisco, could be wrong tho?

In that case he needs to swap his SR520W-FE-K9 for a SR520W-ADSL-K9. The SR520W-FE-K9 does not have a DSL modem built in.

Htech20

16 posts

Geek

Reply # 921405 25-Oct-2013 09:17

Hi Yes that is correct, sorry If I wasnt clear. SO I want to swap out my Thompson and replace it with my Cisco router.

Inphinity I could do that however that would be the LAN done, but the rest of my household uses the wifi which I will need to configure as well.

Htech20

16 posts

Geek

Reply # 921406 25-Oct-2013 09:19

Again sorry for the misleading link for the wrong router, just wanted to show everyone the picture of my router, I do indeed have the SR520W-ADSL-K9 as I do have a DSL Port on the router itself

Htech20

16 posts

Geek

Reply # 921801 25-Oct-2013 17:53

Hi Guys so Im busy trying to config my Cisco SR520W-ADSL-K9 router so that when I plug the DSL cord ito the router I will be able to have Wifi and ADSL internet. I currently have a Thompson router and just need help migrating over to my new Cisco router, unfortuanately it is command base and I need someone who knows how to do this?

Inphinity

2532 posts

Uber Geek
+1 received by user: 940

Subscriber

Reply # 921848 25-Oct-2013 19:26

You should be able to use Cisco Configuration Assistant to configure an SR520W. Honestly, if you're not familiar with the Cisco IOS CLI, CCA is going to be a far better choice.

Htech20

16 posts

Geek

Reply # 921854 25-Oct-2013 19:48

Hi I am very familiar with the Cisco IOS CLI, I currently hold a CCNP Route, however that will not help me here as I dont know whether my config is correct or not, (obviously isn't) so I want to have a crack of it and get some opinions on this site, if you do know how to do this that would definitely be helpful.

Inphinity

2532 posts

Uber Geek
+1 received by user: 940

Subscriber

Reply # 921858 25-Oct-2013 20:02

Should be as simple as setting interface atm0 with PVC 0/100, and dialer0 for PPPoA. You may want to check out Cisco's admin guide for the SR520W.

BinaryLimited

791 posts

Ultimate Geek
+1 received by user: 79

Trusted

Reply # 921859 25-Oct-2013 20:03

Htech20: Hi I am very familiar with the Cisco IOS CLI, I currently hold a CCNP Route, however that will not help me here as I dont know whether my config is correct or not, (obviously isn't) so I want to have a crack of it and get some opinions on this site, if you do know how to do this that would definitely be helpful.

can you post your config file?

Binary Limited - Safe. Secure. Simple. ™
www.binarylimited.co.nz

1 | 2