[WXC/VFX] Help! Need VFX provisioning URL!

Forums › One New Zealand (including Vodafone, WxC, Farmside) › [WXC/VFX] Help! Need VFX provisioning URL!

nic.wise

333 posts

Ultimate Geek

Trusted

#13345 5-May-2007 11:31

Hi there

I'm "stuck" in the US, with my trusty PAP2T, and I need the VFX provisioning URL as I had to hard-reset it :(

It looked something like

http://(ip)/configs/default/something.cfg

(note, I edited a few bits in there, tho mine obviously doesn't work anyway!!) This is what they give you when you sign up.

If anyone has it, can you post it? If it's considered private, please PM me, or email direct (nic dot wise at gmail dot com). I have a PAP2T if it makes a difference

I'd call WxC, but they only have an 0800 on the website, and I'm in the US, so no 0800 from here....

Ta!

Nic Wise - fastchicken.co.nz

1 | 2

3539 posts

Uber Geek

Trusted

#69589 5-May-2007 11:35

Here you go Nic:

http://58.28.20.69/configs/default/default$MA.cfg

It seems to be the same for PAP2T or SPA2102, don't know about other devices.

Cheers,
Grant.

nic.wise

333 posts

Ultimate Geek

Trusted

#69590 5-May-2007 11:45

Grant17: Here you go Nic:

http://58.28.20.69/configs/default/default$MA.cfg

It seems to be the same for PAP2T or SPA2102, don't know about other devices.

Cheers,
Grant.

Thanks Grant, however thats the URL I have.

Last time I tried it (when in NZ) with the "correct" one, I entered it, hit save, and when the box came back up, it just said I can't get into the admin side (which is good :) )

Now, I hit save, it restarts, and.... nothing. I can still get into the admin section, and none of the line info is there :(

Thanks tho!

Nic Wise - fastchicken.co.nz

nic.wise

333 posts

Ultimate Geek

Trusted

#69591 5-May-2007 11:45

nic.wise:
Grant17: Here you go Nic:

http://58.28.20.69/configs/default/default$MA.cfg

It seems to be the same for PAP2T or SPA2102, don't know about other devices.

Cheers,
Grant.

Thanks Grant, however thats the URL I have.

Last time I tried it (when in NZ) with the "correct" one, I entered it, hit save, and when the box came back up, it just said I can't get into the admin side (which is good :) )

Now, I hit save, it restarts, and.... nothing. I can still get into the admin section, and none of the line info is there :(

Thanks tho!

BTW, if I load that in firefox, I get a 404.

Nic Wise - fastchicken.co.nz

nic.wise

333 posts

Ultimate Geek

Trusted

#69593 5-May-2007 12:21

Grant17: Here you go Nic:

http://58.28.20.69/configs/default/default$MA.cfg

It seems to be the same for PAP2T or SPA2102, don't know about other devices.

Cheers,
Grant.

OK, I found it eventually - not like me to not send things to my email archive, given I work for an email archiving company!!

It's VERY close to that URL - I'll just wait until Maverick come on before I post it, as I dont know if it's a public thing or not!!!!

(EDIT) Damn, I thought I had it, but still no

The new one I found:

http://58.28.20.69/tftproot/configs/default/default$MA.cfg

anyone?

:(

Nic Wise - fastchicken.co.nz

coffeebaron

6233 posts

Uber Geek

Trusted

Lifetime subscriber

#69601 5-May-2007 14:16

I'm quite sure that is it, quote from my provisioning email:

To setup your Residential Linksys Device please enter the following Link in the Profile Rule under the provisioning Section of your Linksys Device setup, save the configuration and then power cycle the device. If you have any problems with this please contact our Support team who will be happy to assist you with any issues.

http://58.28.20.69/configs/default/default$MA.cfg

Maybe it is getting stuck between the configs (see my PM)

Rural IT and Broadband support.

Broadband troubleshooting and master filter installs.
Starlink installer - one month free: https://www.starlink.com/?referral=RC-32845-88860-71
Wi-Fi and networking
Cel-Fi supply and installer - boost your mobile phone coverage legally

Need help in Auckland, Waikato or BoP? Click my email button, or email me direct: [my user name] at geekzonemail dot com

maverick

3594 posts

Uber Geek

Trusted

WorldxChange

#69608 5-May-2007 15:02

Nic

You should be good on this one

http://58.28.20.69/configs/default/default$MA.cfg

btw you will get a 404 when using this

, just copy and paste this into the prov link, can you PM your Mac just to make sure we have the correct details please

Yes I am a employee of WxC (My Profile) ... but I do have my own opinions as well

https://www.facebook.com/wxccommunications

nic.wise

333 posts

Ultimate Geek

Trusted

#69620 5-May-2007 16:53

maverick: Nic

You should be good on this one

http://58.28.20.69/configs/default/default$MA.cfg

btw you will get a 404 when using this , just copy and paste this into the prov link, can you PM your Mac just to make sure we have the correct details please

Thanks Phil - still a no go.

Just checking 100% - it's going into the "Provisioning -> Profile Rule" box, right?

Nic Wise - fastchicken.co.nz

Quic Broadband

Move to New Zealand's best fibre broadband service (affiliate link). Note that to use Quic Broadband you must be comfortable with configuring your own router.

nic.wise

333 posts

Ultimate Geek

Trusted

#69623 5-May-2007 17:20

OK, I dont know if Phil did something on their end, or it just happened I did the combination of URL, reset, power etc all at the right time. But it works now!

yay! I have an 04 number here in Madison (hellllllloooooooo Wisconsin etc)

The call clarity is FANTASTIC - just called the folks in Auckland, and it was clear as a bell - even with the frankenstien network setup I have at the moment (I'm one power brick short, so I have an apple airport express plugged into the wall, my mac connecting to it over wifi, and the pap2t plugged into the mac on ethernet using connection sharing.....)

Fantastic - thanks everyone (esp Phil, Grant and CoffeeBaron)

Cheers

N

Nic Wise - fastchicken.co.nz

maverick

3594 posts

Uber Geek

Trusted

WorldxChange

#69629 5-May-2007 18:16

nic.wise:

OK, I dont know if Phil did something on their end, or it just happened I did the combination of URL, reset, power etc all at the right time. But it works now!

N

Power Reset, you need to power reset after you put in the link...sorry should have said this

Yes I am a employee of WxC (My Profile) ... but I do have my own opinions as well

https://www.facebook.com/wxccommunications

nic.wise

333 posts

Ultimate Geek

Trusted

#69658 6-May-2007 05:40

maverick:
nic.wise:

OK, I dont know if Phil did something on their end, or it just happened I did the combination of URL, reset, power etc all at the right time. But it works now!

N

Power Reset, you need to power reset after you put in the link...sorry should have said this

hehe, I should have written it down (will do now :) ). Problem before this was, once I got it setup (thanks!) I basicly left it alone for, um, 6 months or so. I got rebooted once or twice, but other than that..... never even looked at it :) Fantastic

Thanks everyone for the help :)

Mavrick: may be a good promotional thing for kiwi's on their OE - or travelers - "take your 04/09 number with you! TRUE number portability :)"

Nic Wise - fastchicken.co.nz

mattz

23 posts

Geek

#69877 7-May-2007 23:11

Sorry to high-jack this tread, but i'm experiencing the same issue as Nic, I have a new WRTP54G which I have hooked up to my TCL connection, everything is working fine but no matter what I try I can't get the VOIP phone working.

I was on the phone to a tech at WXC for about 30 mins but we could not resolve the problem. Seems the provisioning settings don't stick and it never downloads the required information. I have tried playing round with the logging (to see if it tries to make the connection) but it seems non-existing on the WRT router. The proceedure I followed was as follows:

Login --> Voice --> Login Admin --> advanced view --> provisioning
provisioning rule http://58.28.20.69/configs/default/default$MA.cfg (seems to be same as listed in this thread).
save settings
WRT reboots
power cycle.
wait..... nothing....

Any ideas?? My thinking is that it must be my mac address maybe recorded incorrectly during the initial signup?? I've tried factory reset with the reset button and with the reset to factory in the admin interface. One interesting thing is I can't tick the box to reset voice provider details as it asks me for a user name / password that is unknown to me.

grant_k

3539 posts

Uber Geek

Trusted

#69878 7-May-2007 23:14

Did you try Resetting to Factory Defaults via the IVR (by plugging in a phone)?

maverick

3594 posts

Uber Geek

Trusted

WorldxChange

#69887 8-May-2007 06:40

Hi,

The MAC address we have on file is not the same one as you have given now in the fault ticket

so hence the reason no config for your device, I have fixed this this morning with the info we have in the fault ticket and you should be good to go by the time you read this, you may need a restart but check your lights on the router firsts or easier still pick up the phone and see if you have dial tone.

Yes I am a employee of WxC (My Profile) ... but I do have my own opinions as well

https://www.facebook.com/wxccommunications

maverick

3594 posts

Uber Geek

Trusted

WorldxChange

#69889 8-May-2007 07:47

Just checked your device is now up and online so you should be all good

Yes I am a employee of WxC (My Profile) ... but I do have my own opinions as well

https://www.facebook.com/wxccommunications

mattz

23 posts

Geek

#69892 8-May-2007 08:26

Yay its all up and running, thanks for that and for the super quick turn around, next time over a cell phone i'll say delta echo charlie etc etc.

One question though the Xnet tech originally said just one line on the device would be locked and I would still be able to log in as admin for the second line, i.e. to set up a second sip provider this doesn't appear to be the case and both lines seem to be locked now, not an issue at the moment but in future I may experiment with some overseas providers to get a local number in another country etc.

1 | 2