[WXC/VFX] Setting up WXC Open VFX on Innbox V50U

Forums › One New Zealand (including Vodafone, WxC, Farmside) › [WXC/VFX] Setting up WXC Open VFX on Innbox V50U

Minimad79

9 posts

Wannabe Geek

#142840 26-Mar-2014 12:11

Just had our router replaced by our ISP, as the old Cisco unit died. It has been replaced with an Innbox V50U, which is great, but is not supported by WXC for the standard VFX.

AS a result, we have switched to Open VFX, but I am having issues setting it up.

Any one able to shed a little light on the situation?

1 | 2

266 posts

Ultimate Geek
+1 received by user: 26

#1013095 26-Mar-2014 12:26

Not sure if this works but try this :

Using this as a reference

Under Voice - SIP Basic Settings :

Locale NZL
Tick Use Sip Proxy - pan.wxnz.net
Tick Use Sip Outbound Proxy - pan.wxnz.net
Tick Use Sip Register - pan.wxnz.net

Under SIP Account 0
Tick account enabled
Display name - UserID from your email
Authentication name - AuthID from your email
Password - Password from your email
Preferred ptime 20
Preferred codec 1 G.711Alaw
Preferred codec 2 G.711Ulaw
Preferred codec 3 G729

You might find you need to enter a dialplan in the "Voip Dialplan Setting" if you are having issues dialling out to some numbers, for that you could try copying the dial plans found on these link but that is for cisco devices so I don't know if it would work the same on this device http://blog.2talk.co.nz/pap2t.html

Also there's this thread http://www.geekzone.co.nz/forums.asp?topicid=113693 which may be of help

Let me know how you go :)

Andrei.

hio77

12999 posts

Uber Geek
+1 received by user: 3867

ID Verified

Trusted

Lizard Networks

#1013096 26-Mar-2014 12:27

What configuration do you currently have in there?

#include <std_disclaimer>

Any comments made are personal opinion and do not reflect directly on the position my current or past employers may have.

grudge

266 posts

Ultimate Geek
+1 received by user: 26

#1013121 26-Mar-2014 12:50

Try entering Sip Domain Name as pan.wxnz.net

Minimad79

9 posts

Wannabe Geek

#1013122 26-Mar-2014 12:52

Try that again :/

https://cdn.geekzone.co.nz/imagessubs/blog764bf0211bef1bef32d60d3291cefe15.jpg

grudge

266 posts

Ultimate Geek
+1 received by user: 26

#1013126 26-Mar-2014 12:55

Can you also please PM me your IP as shown here ? http://www.whatismyip.com/

Minimad79

9 posts

Wannabe Geek

#1013127 26-Mar-2014 12:55

grudge: Try entering Sip Domain Name as pan.wxnz.net

Tried that, and I get an engaged tone.

When I remove the SIP Registrar, i get a dial tone, but it neither incoming or outgoing calls work.

grudge

266 posts

Ultimate Geek
+1 received by user: 26

#1013150 26-Mar-2014 13:35

Let's try :

Leave SIP domain name blank
under sip registrar change the port to 5060
Extension - your phone number

Also for codec preference :

1-g722
2-g711Alaw
3-g711Ulaw
4-g729a

Samsung

Shop now on Samsung phones, tablets, TVs and more (affiliate link).

Minimad79

9 posts

Wannabe Geek

#1013197 26-Mar-2014 14:33

grudge: Let's try :

Leave SIP domain name blank
under sip registrar change the port to 5060
Extension - your phone number

Also for codec preference :

1-g722
2-g711Alaw
3-g711Ulaw
4-g729a

That gives me a dial tone, but again, not inbound or outbound calls.

When I call in, I get a recorded message saying my number is unavailable.

grudge

266 posts

Ultimate Geek
+1 received by user: 26

#1013202 26-Mar-2014 14:41

That is looking a bit better,

I can see that your device is registered, however when trying to call in we are not getting a reply to our INVITE message so the call times out (you hear the RVA about number unavailable)
When you are calling out again there are timeouts during the call setup process.

Does your device have a setting called SIP ALG ? Try turning it off, also see if it's possible to change the signalling protocol from UDP to TCP. Can't really help with where you'd find these settings as I am not finding a detailed user guide for this device.

Minimad79

9 posts

Wannabe Geek

#1013203 26-Mar-2014 14:41

Right - To make things weirder, I CAN call out. I called my cellphone, and the call goes through. But the home phone shows no indication that there is an outgoing call.

Still can not receive in bound calls though :(

Minimad79

9 posts

Wannabe Geek

#1013204 26-Mar-2014 14:49

I have changed the signalling protocol, and that has solved the outgoing calls issue. Trying to find the SIP ALP at the moment.

grudge

266 posts

Ultimate Geek
+1 received by user: 26

#1013205 26-Mar-2014 14:50

Looks like incoming is working too (that was me ringing just then :) )

Minimad79

9 posts

Wannabe Geek

#1013206 26-Mar-2014 14:52

Ha :) Weird thing is though, my phone didn't ring. Just had my wife call from work, and she got the same issue - call goes though, but goes to the invite message.

Just trying to find the SIP ALG at the moment

grudge

266 posts

Ultimate Geek
+1 received by user: 26

#1013211 26-Mar-2014 15:05

Is your handset plugged into the 1st phone port of that device ? Do you have the Ringer Volume on your phone turned all the way up ?

Also, what do you see under Global Parameters under the Voip Menu ? Can you add a screen shot ?

Minimad79

9 posts

Wannabe Geek

#1013213 26-Mar-2014 15:09

grudge: Is your handset plugged into the 1st phone port of that device ? Do you have the Ringer Volume on your phone turned all the way up ?

Also, what do you see under Global Parameters under the Voip Menu ? Can you add a screen shot ?

-Plugged into 1st port (TEL1)
-Ringer volume is full

Screen shot of global parameters.

https://cdn.geekzone.co.nz/imagessubs/blog20e96e27e852f90a4ac238dd51fef2b9.jpg

1 | 2