Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.




4 posts

Wannabe Geek


#192303 5-Mar-2016 20:07
Send private message

I'm having a nightmare with my freeview setup.

 

I established that I needed the Freeview Sattelite box after finding out that Hataitai, Wellington was not in the HD coverage region. Luckily the tenant in the apartment before us had Sky set up so after some searching I read that I was able to simply use the Sky sattelite dish for freeview so i purchased the Freeview Sattelite (Transonic version). 

 

Now in my apartment there are two wires coming into the house. Both are sattelite cables as they are the screw needle connections (i think called coaxial) one of these wires is connected to a Kingray TV amp that is plugged into the power socket with another coxial wire from the amp to nothing (see picture) this is what i assume is to be connected to FV Sat receiver. The other coxial wire coming from outside (black) is on its own. See photos.

 

 

 

 

Now I have connected both these wires (individually) into the receiver and done a scan (from initial setup and after factory restoring) and not only do no channels get picked up but the Strength appears 0% as does the Quality. 

 

I have done a full day of researching what i could possibly have done wrong but nothing seems to be working. I found a thread discussing the sattelite dish could potentially be set to the Sky LNB frequency but even changing the frequency does not pick up anything. 

 

My neighbours keep to themselves so Im thinking thats my last option to go door knocking

 

PLEASE HELP. I'ts also saturday and no freeview or dishtv or Transonic supplier is open to talk to meee

 

 


Filter this topic showing only the reply marked as answer Create new topic
5962 posts

Uber Geek


  #1506605 5-Mar-2016 20:31
Send private message

Those connectors are called f connectors. They can and are used for non satellite signals, so don't assume there is a dish.

Have you checked outside to see if there is a dish? It's more likely a terrestrial uhf antenna if there's an amp connected. Do you have built in Freeview hd on your tv to try that?

If there is a dish, use the cable that doesn't go through the amp. Tell us what lnb settings you have used so we can check



4 posts

Wannabe Geek


  #1506619 5-Mar-2016 20:51
Send private message

There's definitely a satellite dish which services the entire apartment block (i think) out there I can see it from my balcony (its directly below) and I can visually trace one of my f connectors to it- the one connected to the white adapter. The other f connector (black one) is going up to the roof and I walked out to the other side of street today to see if there's anything up there and there is a really big aerial up there lying horizontally. 

 

After i did a location search i found that my place in not in the uhf aerial zone for freeview hd so had no choice but to use satellite. 

 

The scan details ive been trialling are in the photo here LNB low and high at 11300 (as recommended by FV site)

 

 

 

 

I have also gone through each satellite setting and the strength and quality for each remains at 0%

 

Side dumb question- Am i right to be putting in the f connector from outside into the "LNB Input" of the receiver box and for there to be nothing in the socket of the "LNB out"? 


 
 
 
 




4 posts

Wannabe Geek


  #1506620 5-Mar-2016 20:53
Send private message

Also there is not built in freeview in my tv. 


2502 posts

Uber Geek

Lifetime subscriber

  #1506622 5-Mar-2016 21:19
Send private message

Start by turning off the 22 kHz. And experiment with 10750 MHz.

 

Note: Those amplifiers are NOT designed for L band DVB-S signals, they are VHF/UHF and connect to a terrestrial antenna.





Spark FibreMAX using Mikrotik CCR1009-8G-1S-1S+. UAP, UAP AC Pro, UAP AC Pro Mesh, Apple TV 4, Apple TV 4K, iPad Air 1, iPhone 6s, VodaTV Gen 2. If it doesn't move then it's data cabled.


1959 posts

Uber Geek


  #1506640 5-Mar-2016 22:12
Send private message

Judging from your picture I would guess the white lead from the Kingray Amp is UHF and needs to be plugged into a Freeview TV or a UHF STB.

 

The black lead will be the Satellite Dish lead. Satellite dishes don't need an amplifier in the co-ax line and the Kingray amps are normally VHF/UHF.


Devastation by stupidity
12240 posts

Uber Geek

Lifetime subscriber

  #1506689 5-Mar-2016 23:58
Send private message

You are right to use the lnb input. The other is just a pass through. It is possible, as B1GGLZ suggests, that the previous occupant had UHF TV even if it is not officially in the reception area. Maybe that is what the amplifier was for. It is also possible that is an old VHF installation. The big aerial on the roof that you describe might have been for VHF. 

 

 





I don't think there is ever a bad time to talk about how absurd war is, how old men make decisions and young people die. - George Clooney
 


147 posts

Master Geek


  #1506749 6-Mar-2016 08:30
Send private message

As suggested by the OP switching off the 22 Khz tone may help if your dish/lnb looks like the attached photo of a Sky 10750Mhz

 

LNB. Unfortunately these LNBs had a tendency to drift off frequency (the LO frequency in the drop-down list in your screenshot) so maybe

 

try setting 10700 Mhz and re-scanning if 10750 doesn't work for you.

 

 

Hopefully the image works, first time I have tried this.

 

 


 
 
 
 


5962 posts

Uber Geek


  #1506777 6-Mar-2016 10:23
Send private message

In your settings try:

 

 

 

LNB Lo: 10750

 

LNB Hi: 10750

 

22kHz: Off

 

LNB Power: Off

 

DiSEqC: Off

 

Some distribution systems in apartments don't need LNB power supplied - generally this is on, but some buildings may require it off.

 

22kHz should always be off, as should DiSEqC

 

LNB Hi & Lo should be the same, and depend on the LNB installed on the dish. 10750, 11300, 10700 are the most common, from most to least common.




4 posts

Wannabe Geek


  #1506818 6-Mar-2016 11:32
Send private message

RunningMan your settings worked its magic!!
Thank you all for your help!

Filter this topic showing only the reply marked as answer Create new topic



Twitter and LinkedIn »



Follow us to receive Twitter updates when new discussions are posted in our forums:



Follow us to receive Twitter updates when news items and blogs are posted in our frontpage:



Follow us to receive Twitter updates when tech item prices are listed in our price comparison site:





News »

Menulog change colours as parent company merges with Dutch food delivery service
Posted 2-Jul-2020 07:53


Techweek2020 goes digital to make it easier for Kiwis to connect and learn
Posted 2-Jul-2020 07:48


Catalyst Cloud launches new Solutions Hub to support their kiwi Partners and Customers
Posted 2-Jul-2020 07:44


Microsoft to help New Zealand job seekers acquire new digital skills needed for the COVID-19 economy
Posted 2-Jul-2020 07:41


Hewlett Packard Enterprise introduces new HPE GreenLake cloud services
Posted 24-Jun-2020 08:07


New cloud data protection services from Hewlett Packard Enterprise
Posted 24-Jun-2020 07:58


Hewlett Packard Enterprise unveils HPE Ezmeral, new software portfolio and brand
Posted 24-Jun-2020 07:10


Apple reveals new developer technologies to foster the next generation of apps
Posted 23-Jun-2020 15:30


Poly introduces solutions for Microsoft Teams Rooms
Posted 23-Jun-2020 15:14


Lenovo launches new ThinkPad P Series mobile workstations
Posted 23-Jun-2020 09:17


Lenovo brings Linux certification to ThinkPad and ThinkStation Workstation portfolio
Posted 23-Jun-2020 08:56


Apple introduces new features for iPhone iOS14 and iPadOS 14
Posted 23-Jun-2020 08:28


Apple announces Mac transition to Apple silicon
Posted 23-Jun-2020 08:18


OPPO A72 a top mid-tier smartphone
Posted 19-Jun-2020 18:02


D-Link A/NZ launches new smart AX1500 Wi-Fi 6 Router
Posted 19-Jun-2020 15:03



Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.


Support Geekzone »

Our community of supporters help make Geekzone possible. Click the button below to join them.

Support Geezone on PressPatron



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.

Alternatively, you can receive a daily email with Geekzone updates.