[WXC/VFX] Help!! Setting Up VFX with Vodafone HG and Cisco WIP310

Forums › One New Zealand (including Vodafone, WxC, Farmside) › [WXC/VFX] Help!! Setting Up VFX with Vodafone HG and Cisco WIP310

CapinNeemo

11 posts

Geek

#73019 7-Dec-2010 13:12

Hi im new to VFX and have never really done and VOIP setups before i've had a read and had a good playing with everysetting i can think of.

I have a Vodafone Hg Router and a Cisco WIP310 IP Wireless G phone.

So far i've managed to have the phone all setup bnut it says NOT REGISTERED so i'm lost

can anyone help?

Thanx Jono

Niel

3267 posts

Uber Geek

Trusted

#414321 7-Dec-2010 22:11

Easy setup is with XNet VFX approved hardware http://www.xnet.co.nz/vfx/hardware.shtml
It requires only entering 1 line, the rest takes care of itself (after application processed by XNet). You will then no longer have access to the phone config, but you will also not be responsible for it.

The harder way is to use hardware which is not approved, but apply for an Open VFX account where you are responsible for the errors you make. Not recommended unless you know exactly what you are doing.

You can never have enough Volvos!

CapinNeemo

11 posts

Geek

#414467 8-Dec-2010 10:01

Sorry i must have not been clear enough i was not aware of this when i got it all setup and have already purchased non recommened gear.

I have open vfx setup just would like a little help as to setup by myself once someone points me i the right direction im sure i can setup the hardware my self i been working on computers for years and know what im doing.

Just haven't had any experiance with VOIP

CapinNeemo

11 posts

Geek

#414996 9-Dec-2010 13:17

So there is no one here that has setup a non certified device and can give me any advice.

Oh well back to the drawning board and if i figure it out will post to help other like me thanx for nothing guys.

Jono

sbiddle

30853 posts

Uber Geek

Retired Mod

Trusted

Biddle Corp

Lifetime subscriber

#415004 9-Dec-2010 13:28

You only need to enter the 4 settings that WxC give in your account settings.

Proxy, Username, AuthID and password. Set AuthID to yes.

CapinNeemo

11 posts

Geek

#415236 9-Dec-2010 20:22

I realise this im not a complete noob iḿ just wondering where i put these settings in my WIFI phone or my router this is what i am confused with.

sbiddle

30853 posts

Uber Geek

Retired Mod

Trusted

Biddle Corp

Lifetime subscriber

#415251 9-Dec-2010 21:11

CapinNeemo: I realise this im not a complete noob iḿ just wondering where i put these settings in my WIFI phone or my router this is what i am confused with.

You enter them in to your phone in the Proxy, UserID, AuthID and Password fields and select Yes in AuthID.

A sarcastic "thanx for nothing guys" isn't going to get you much help from those of us who do know how to configure these things..

CapinNeemo

11 posts

Geek

#415265 9-Dec-2010 21:26

Right apologies for the bluntness of my last few posts. Have had allot of difficulty with this and was pulling my hair out.

Went to the Cisco forums and found someone who has been though the same thing. I didn see the tiny Admin Login link in the top right on the screen. This gives you access to the Ext 1 tab.

Under this tab you are able to put in all the settings needed. so now if anyone else has this phone i know it works on open VFX.