Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.


Goosey

3016 posts

Uber Geek
+1 received by user: 871

Subscriber

#75799 23-Jan-2011 16:49
Send private message

Hi all, 

My landline and BB is with Vodafone, so posting here makes some sense.

Anyhow,

With all this rain here in Auckland and our house being below road level, the phone wiring in the street is via pole and with our house down a driveway, our wiring from the street is via undergound conduit.

The POP is mounted on the house about 30cm above the ground. Previously had a Chrous guy scratch his head in wondering why the little box was moist and showed signs of water entering it.

Guess... The water is entering at street level, running down the conduit and the result is a fountain at my POP.
Wonderful ! This perhaps explains my sometimes bad scratchy and low volume phone calls.  

So where to now?  Can I log a job with Vodafone to see if someone can seal up the point where water is entering?

The water is clear and free of dirt, so I dont think its from a crack in the conduit somewhere along the run, I suspect its from the pole where it starts its run from.

Would it pointless silicon filling the POP?  i.e. would just create a huge conduit full of water and bust somewhere else?

Cheers
Goose

 

Create new topic
TechSol
300 posts

Ultimate Geek
+1 received by user: 30

Technical Solutions Aust

  #430529 24-Jan-2011 12:36
Send private message

I have seen telecom seal this kind of thing with a small inflatable bag... think they fill the back with CO2 or something. Anyway, it's a 2 minute job that will seal the conduit perfectly.... however that doesn't stop water sitting in the conduit and potentially causing issues with the cable itself... depending on the cable of course.

I would imagine you could log a job.



cyril7
9075 posts

Uber Geek
+1 received by user: 2499

ID Verified
Trusted
Subscriber

  #430558 24-Jan-2011 13:33
Send private message

Hi, Sealing the top is one course of action, but also relieving the conduit at the bottom below the ETP (its not a POP but ETP) would make more sense, make a small hole or slot but dont hit the cable, this would keep the water in the conduit below the joint in the ETP.

The leadin cable has a heavy duty polyethylene sheath that is designed to survive underwater and at considerable pressure (that it would not be subject to here). The joint in the ETP is designed to survive slight wetting but not to sit for any time in water.

Cyril

Goosey

3016 posts

Uber Geek
+1 received by user: 871

Subscriber

  #430665 24-Jan-2011 18:31
Send private message

cyril7: Hi, Sealing the top is one course of action, but also relieving the conduit at the bottom below the ETP (its not a POP but ETP) would make more sense, make a small hole or slot but dont hit the cable, this would keep the water in the conduit below the joint in the ETP.

The leadin cable has a heavy duty polyethylene sheath that is designed to survive underwater and at considerable pressure (that it would not be subject to here). The joint in the ETP is designed to survive slight wetting but not to sit for any time in water.

Cyril



Thanks guys. Given me good reason to request a visit from a tech....I dont think its my responsibility beyond this cable joining my house, (feel free to correct me if im wrong).  If it ends up that nobody wants to take ownership... 'to the drill i go'...with a bit of silicone.

Cheers
 



cyril7
9075 posts

Uber Geek
+1 received by user: 2499

ID Verified
Trusted
Subscriber

  #430683 24-Jan-2011 19:06
Send private message

Hi, dont be surprised if you get no interest, there are plenty of other wet phone joints about at the moment.

Cyril

Create new topic








Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.