connecting ipaq 5450 to billinton usb dongle bluetooth device

Forums › LAN (ethernet/Wifi/routers/Bluetooth) › connecting ipaq 5450 to billinton usb dongle bluetooth device

sjbush

4 posts

Wannabe Geek
Inactive user

#161 31-Mar-2003 16:31

I have a billinton usb dongle bluetooth device. I have loaded the most recent drivers and set the ipaq up as per the instructions. I have also set the com port on the PC activesync to com 5. When using the blue tooth manager the two devices seem to try to connect ie the icon on the pc goes green also on checking "my bluetooth places" The ipaq is there. I am using XP and version 3.6 of active sync. I have version 1.3.2.7 driver

freitasm

BDFL - Memuneh
80646 posts

Uber Geek
+1 received by user: 41029

Administrator

ID Verified

Trusted

Geekzone

Lifetime subscriber

#143 31-Mar-2003 17:51

Hi!

What iPAQ model are you using?

Referral links: Quic Broadband (free setup code: R587125ERQ6VE) | Samsung | AliExpress | Wise | Sharesies

Support Geekzone by subscribing (browse ads-free), or making a one-off or recurring donation through PressPatron.

David Hettel

73 posts

Master Geek

#144 31-Mar-2003 20:17

With the 1.3.2.7 Software, you will get prompted twice for a connection, once down by the tray, and once in the middle of the screen. If you do not answer these prompts fast enough, the connection will be broken. It is best to check always allow this connection.

David

sjbush

4 posts

Wannabe Geek
Inactive user

#146 31-Mar-2003 23:57

I am using a hp iPAQ h5450

David

I am not getting any prompts at all the blue tooth icon on the pc just goes green and then after a short time I get the eror message that the connection has timed out

David Hettel

73 posts

Master Geek

#148 1-Apr-2003 10:27

Ok, then have you modify the settings? Or does this just not happen, and never has. If this is the case, you may want to think about reinstalling the software. Right click on the icon in the tray, then Advanced Configuration. Click the Local Services tab, then go to Bluetooth Serial port, highlight it and click properties. On the new window click on Notifications. Is Audio and visual checked?

David

sjbush

4 posts

Wannabe Geek
Inactive user

#151 1-Apr-2003 16:18

Ok

So I removed the bluetooth software user the add or remove function and restalled. I have not changed any of the settings since the reinstallation. I was ask to provide passwords for both the laptop and the ipaq during the reinstallation process. I also soft reset the ipaq and re setup the active sync using BT manager on the ipaq. I have also checked that the port under connection setting in active sync on the pc is serial port 5 . I have aslo checked the audio and visual boxes are ticked as you suggested

After all this I still have the same problem

David Hettel

73 posts

Master Geek

#159 3-Apr-2003 09:31

I don't know if this would apply to you or not. But I have noticed that if there are three or more Bluetooth devices in the same room, it can take a while for them to connect. Much longer than I would think.

From rereading your post it is not clear to me if the Computer you are syncing to is the same one you are conecting to for the Bluetooth connection.

David

Dyson

Shop now for Dyson appliances (affiliate link).

sjbush

4 posts

Wannabe Geek
Inactive user

#180 11-Apr-2003 01:39

I am only using one computer and one bluetooth device that is the ipaq and the computer its still timing out

freitasm

BDFL - Memuneh
80646 posts

Uber Geek
+1 received by user: 41029

Administrator

ID Verified

Trusted

Geekzone

Lifetime subscriber

#181 11-Apr-2003 07:02

You said you setup the Activesync port to COM5... Is this the same COM you have in the Services part of your Bluetooth configuration? Are you sure you don't have other devices using the same port (a modem?)

Referral links: Quic Broadband (free setup code: R587125ERQ6VE) | Samsung | AliExpress | Wise | Sharesies

Support Geekzone by subscribing (browse ads-free), or making a one-off or recurring donation through PressPatron.

David Hettel

73 posts

Master Geek

#182 11-Apr-2003 08:09

Yes you might want to recheck that COM port, #5 is normally the one listed for Client Applications, and not the one listed for Local Services, which is 6. You need to set ActiveSync to the COM port listed on the bottom of Local Services.

David