Magic TV 3600

Forums › Freeview (DVB-T/DVB-S) › Magic TV 3600

marlinz

441 posts

Ultimate Geek
+1 received by user: 96

#165865 23-Feb-2015 11:36

Have a problem with my magic tv 3600, I was playing up so i turned it off , when i turned it back on the magic tv boot screen would load for about 15 or more seconds then nothing happens.

Cannot turn off the unit via the remote and all that comes on the front screen of the magic tv unit is "magic tv " and nothing at all on the tv

Tried to install new firmware but all the shows when i tried that is "no storage detected "

Any suggestions ?

Amazon Echo

Amazon Dot

Lifx Bulbs

Nexus 5X
Magic TV 3600
Sony EX700

Unblocking service
Amazon Fire TV x 2 = Netflix USA + Amazon Prime
Lightbox

old3eyes

9158 posts

Uber Geek
+1 received by user: 1364

Subscriber

#1244717 23-Feb-2015 12:30

Did you turn it off and pull out the power plug?? I had a similar problem with Magic DVR last year and that fixed it for me.. Left it unplugged for about 30 minutes..

Regards,

Old3eyes

marlinz

441 posts

Ultimate Geek
+1 received by user: 96

#1244723 23-Feb-2015 12:43

old3eyes: Did you turn it off and pull out the power plug?? I had a similar problem with Magic DVR last year and that fixed it for me.. Left it unplugged for about 30 minutes..

yup for over 24 hours :(

Amazon Echo

Amazon Dot

Lifx Bulbs

Nexus 5X
Magic TV 3600
Sony EX700

Unblocking service
Amazon Fire TV x 2 = Netflix USA + Amazon Prime
Lightbox

cb1

339 posts

Ultimate Geek
+1 received by user: 44

#1244782 23-Feb-2015 13:43

Might need to follow steps 1-5 stated in the owner's guide Rescue Procedure (p.69 of Owners Guide ver 1). I believe you need to use an official Magic tv firmware version rather than one of the 2lostkiwis patched versions, but that can be installed once you get the unit back up and running.

marlinz

441 posts

Ultimate Geek
+1 received by user: 96

#1244806 23-Feb-2015 13:55

cb1: Might need to follow steps 1-5 stated in the owner's guide Rescue Procedure (p.69 of Owners Guide ver 1). I believe you need to use an official Magic tv firmware version rather than one of the 2lostkiwis patched versions, but that can be installed once you get the unit back up and running.

will try again tomorrow , but i did use the offical firmware from http://www.mymagictv.co.nz/support.html downloads section

and do as listed on page 69 of owners manual

Amazon Echo

Amazon Dot

Lifx Bulbs

Nexus 5X
Magic TV 3600
Sony EX700

Unblocking service
Amazon Fire TV x 2 = Netflix USA + Amazon Prime
Lightbox

cb1

339 posts

Ultimate Geek
+1 received by user: 44

#1244827 23-Feb-2015 14:12

Also try using a different flash drive - for some reason, the rescue procedure didn't like the flash drive I have always used to upgrade firmware, but an older/smaller one worked fine.

marlinz

441 posts

Ultimate Geek
+1 received by user: 96

#1245095 23-Feb-2015 19:16

cb1: Also try using a different flash drive - for some reason, the rescue procedure didn't like the flash drive I have always used to upgrade firmware, but an older/smaller one worked fine.

thanks will try that also

Amazon Echo

Amazon Dot

Lifx Bulbs

Nexus 5X
Magic TV 3600
Sony EX700

Unblocking service
Amazon Fire TV x 2 = Netflix USA + Amazon Prime
Lightbox

Samsung

Shop now on Samsung phones, tablets, TVs and more (affiliate link).

marlinz

441 posts

Ultimate Geek
+1 received by user: 96

#1246259 25-Feb-2015 11:40

cb1: Also try using a different flash drive - for some reason, the rescue procedure didn't like the flash drive I have always used to upgrade firmware, but an older/smaller one worked fine.

I tried a different flash drive and wo and behold i have a working Magic TV again

the mrs will be so happy

thank you all for your suggestions

Amazon Echo

Amazon Dot

Lifx Bulbs

Nexus 5X
Magic TV 3600
Sony EX700

Unblocking service
Amazon Fire TV x 2 = Netflix USA + Amazon Prime
Lightbox