Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.


andrewdixon1000

73 posts

Master Geek


#25687 29-Aug-2008 08:55
Send private message

Hi,

I've set up my motherboard and Windows (see signature for details) to use Standby mode.  The PC will go into standby after 20 minutes of idle or if I press the sleep button on my keyboard.  It appears to be going into standby correctly as Windows says "Preparing to Standby" and the computer turns off after a couple of seconds.  When I press the power button on my MCE remote or on the case the computer comes to life but rather than resuming into windows it does a restart.

Does anyone know what I might be doing wrong?  As far as I can tell I have the bios setup correctly.

Thanks
Andy

Create new topic
Little
81 posts

Master Geek


  #160638 29-Aug-2008 09:43
Send private message

andrewdixon1000: Hi,

I've set up my motherboard and Windows (see signature for details) to use Standby mode.  The PC will go into standby after 20 minutes of idle or if I press the sleep button on my keyboard.  It appears to be going into standby correctly as Windows says "Preparing to Standby" and the computer turns off after a couple of seconds.  When I press the power button on my MCE remote or on the case the computer comes to life but rather than resuming into windows it does a restart.

Does anyone know what I might be doing wrong?  As far as I can tell I have the bios setup correctly.

Thanks
Andy


I had trouble resuming from sleep when I had Gigabytes hardware monitoring software installed. Once all of that was uninstalled it worked fine. This was the case for both XP SP3 and Vista Ultimate SP1.

 
 
 

Shop Mighty Ape for electronics, games, computers books and more (affiliate link).
andrewdixon1000

73 posts

Master Geek


  #160683 29-Aug-2008 11:26
Send private message

Thanks Little,

Not sure if I have the Gigabyte hardware monitor installed but I'll look into it tonight.

Thanks
Andrew

allstarnz
1717 posts

Uber Geek

Trusted

  #160688 29-Aug-2008 11:37
Send private message

i might try this too,  have had lots of issues trying to resume from standby with my Gigabyte mobo

all three 'lock lights' will flash on my keyboard, then it will initialise normal start sequence



Little
81 posts

Master Geek


  #160694 29-Aug-2008 12:03
Send private message

The apps I uninstalled were:

Dynamic Energy Saver Advanced
EasyTune 6

Hope that helps :).

andrewdixon1000

73 posts

Master Geek


  #160900 30-Aug-2008 16:20
Send private message

Unfortunately I didn't have any of the Gigabyte software installed so no luck there.

Andy

1gkar
722 posts

Ultimate Geek


  #161064 31-Aug-2008 17:44
Send private message

Andrew,

I'm really sorry to hear about your HTPC issues. But I'm afraid the news is probably not what you wanted hear.

I, too, had issues with standby resumption issues -not the same as yours, though- with the exact same CPU & Gigabyte mobo, but different model: GA-M56S-S3. Nothing I tried worked. I eventually gave up & traded to Intel. Here are the threads for your perusal. I hope you can sort it out; but if not, don't waste too much time on the issue. It can get the best of one: I knowCry

http://forum.team-mediaportal.com/htpc-projects-42/major-amd-gigabyte-issues-i-had-htpc-build-39309/

http://www.geekzone.co.nz/forums.asp?ForumId=84&TopicId=21275

Take specific note of the last thread in the bottom post, regarding working with another CPU.




Silverstone LC14 HTPC Case/Intel E4600 CPU/GA-EP35-DS3 MOBO/Asus EN9500GT graphics/2GB RAM/total 2TB HDD space/HVR-2200 & 2X 150MCE tuner cards/LG GGC-H20L BD Drive/MCE2005/Mediaportal/TVServer 1.1.0Final/LG 55"3D LED-TV/Denon AVR-1803 receiver/X1 projector

andrewdixon1000

73 posts

Master Geek


  #161216 1-Sep-2008 11:26
Send private message

Thanks for the info 1gkar (despite the bad news).  I've raised a ticket with Gigabyte to see what they have to say.  And in the meantime I'll keep searching for a solution.

Thanks
Andy



aucklander
472 posts

Ultimate Geek


  #162363 5-Sep-2008 08:52
Send private message

Sleep / Hibernation appear to work correctly for my setup, but I cannot use them, and I will explain why, maybe you have a workaound...

I have MP set to start with Windows. When I reboot the computer, all is OK, MP starts up and goes strainght into fullscreen live TV, last channel I was watching before shutdown. I have the TV server to turn pc to sleep after 2minutes.

Problems started to rise when I wanted to use PowerScheduler plugin.
After reboot and watching tv or a starting a recording, computer goes to sleep when recording is completed, but when it wakes up from S3 state for the next recording, MP displays "unable to start graph", and then nothing happens. If the client does nothing for 2 minutes, TV server is set to switch PC back into sleep (S3). But there is a recording scheduled, so for the whole duration of that scheduled recording, the PC switches on and off, unable to record due to the error message.

When the time for the scheduled recording expires, all is fine, computer stays in sleep state until the next scheduled recording, when it starts to turn on/off every 3-4 minutes, as described above.

Any ideas why this is happening? I would like to use the PowerScheduler plugin, many people reported it works.
I found a plugin able to turn the pc off after 60 min or 120 min, and I use that if the recording extends up to 1h or 2h after I do not watch tv anymore. If the recording extends more than 2 h after "bed time", I have to let the pc running all night... and I would like to avoid doing that.




mobo Intel DH55PJ, RAM: 4GB RAM, Nova-T 500 HD + Avermedia Trinity tuner card, Geforce 520 video, 120GB SSD Sandisk + 640 WD + 1000SG, Win7 Home Prem 64-bit, Media Portal 1.15.0; BTC 9019URF Cordless Keyboard, Panasonic 55" (HDMI cable), HTPC Case Silverstone Grandia GD05B.


andrewdixon1000

73 posts

Master Geek


  #162365 5-Sep-2008 09:02
Send private message

Hi Aucklander,

The only thing I can think of off the top of my head is in the config for the TV-server part of the PowerScheduler plugin.  Go into the Advanced tab and check "Reinitialize service on wakeup (also reinitialized tuner)", if you don't have it checked already.  It's a long shot, but it's possible that your tuner is not waking up properly and that is what is breaking the graph.

Good luck
Andy

1gkar
722 posts

Ultimate Geek


  #162655 6-Sep-2008 16:32
Send private message

aucklander: Sleep / Hibernation appear to work correctly for my setup, but I cannot use them, and I will explain why, maybe you have a workaound...

I have MP set to start with Windows. When I reboot the computer, all is OK, MP starts up and goes strainght into fullscreen live TV, last channel I was watching before shutdown. I have the TV server to turn pc to sleep after 2minutes.

Problems started to rise when I wanted to use PowerScheduler plugin.
After reboot and watching tv or a starting a recording, computer goes to sleep when recording is completed, but when it wakes up from S3 state for the next recording, MP displays "unable to start graph", and then nothing happens. If the client does nothing for 2 minutes, TV server is set to switch PC back into sleep (S3). But there is a recording scheduled, so for the whole duration of that scheduled recording, the PC switches on and off, unable to record due to the error message.

When the time for the scheduled recording expires, all is fine, computer stays in sleep state until the next scheduled recording, when it starts to turn on/off every 3-4 minutes, as described above.

Any ideas why this is happening? I would like to use the PowerScheduler plugin, many people reported it works.
I found a plugin able to turn the pc off after 60 min or 120 min, and I use that if the recording extends up to 1h or 2h after I do not watch tv anymore. If the recording extends more than 2 h after "bed time", I have to let the pc running all night... and I would like to avoid doing that.


One thing you could try is a little nugget of an app called MCE Standby. It even has a tab for Mediaportal. I might retry it in the near future as my HTPC occasionally won't resume with my MCE remote & have to walk to the case. it only has occurred since I upgraded to MP RC2.




Silverstone LC14 HTPC Case/Intel E4600 CPU/GA-EP35-DS3 MOBO/Asus EN9500GT graphics/2GB RAM/total 2TB HDD space/HVR-2200 & 2X 150MCE tuner cards/LG GGC-H20L BD Drive/MCE2005/Mediaportal/TVServer 1.1.0Final/LG 55"3D LED-TV/Denon AVR-1803 receiver/X1 projector

Create new topic





News and reviews »

Synology Introduces BeeStation
Posted 23-Feb-2024 14:14


New One UI 6.1 Update Brings Galaxy AI to More Galaxy Devices
Posted 23-Feb-2024 10:50


Amazon Echo Hub Available in New Zealand
Posted 23-Feb-2024 10:40


InternetNZ Releases Internet Insights 2023
Posted 20-Feb-2024 10:31


Seagate Adds 24TB IronWolf Pro Hard Drives for Multi-user Commercial and Enterprise RAID Storage Solutions
Posted 19-Feb-2024 16:54


Seagate Skyhawk AI 24TB Elevates Edge Security Capacity and Performance
Posted 9-Feb-2024 17:18


GoPro Releases Quik Desktop App for macOS and Introduces Premium+ Subscription Tier
Posted 9-Feb-2024 17:14


Ring Introduces New Ring Battery Video Doorbell Pro
Posted 9-Feb-2024 16:51


Galaxy AI Transforms the new Galaxy S24 Series
Posted 18-Jan-2024 07:00


D-Link launches AI-Powered Aquila Pro M30 Wi-Fi 6 Mesh Systems
Posted 17-Jan-2024 20:02


Newest LG 4K Lifestyle Projector Doubles as Art Objet
Posted 9-Jan-2024 15:50


More LG Smart TV Owners Set To Enjoy the Latest webOS Upgrade
Posted 9-Jan-2024 15:45


Panasonic Announces the Z95A and Z93A With Fire TV Built In
Posted 9-Jan-2024 15:30


Amazon Echo Pop Review
Posted 8-Jan-2024 14:22


Samsung Tab S9 FE Review
Posted 17-Dec-2023 08:26









Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.







GoodSync is the easiest file sync and backup for Windows and Mac