Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.


Filter this topic showing only the reply marked as answer View this topic in a long page with up to 500 replies per page Create new topic
1 | 2 | 3 
bagheera
544 posts

Ultimate Geek
+1 received by user: 189


  #1055744 29-May-2014 10:50
Send private message

cdrnet:
bagheera:
cdrnet:  The last time I used Powerline technology, it only worked at 11Mb/s. They were talking about increasing the speed to something like 88Mb/s, but I did find it reliable. The error correcting side of Wireless makes the actual performance difficult to measure, so I do quite like such reliable solutions. What speed does it work at these days?


depends - can go upto 300mbs (or at least the one we got could), but if it a long run thought the power cable it drops off, and to the master bed room it was very low - can not remember how low it was but it like xdls - over x distance it drops off.


WOW - Sounds great. I had no idea. I'm considering running a new cable and the route I had planned to take is likely to take around 4 hours of crawling around in dirt and dust, through my roof cavity. If I was to use a Powerline device, I estimate that the actual distance will be around 60m. How would 60m measure up in terms of achieving 300mb/s ?


also depend on how the power is lay out - 60m could = 300m of power cable by the time it gone from 1 plug back to the power board and back out to the other plug - only way to know is to try one.



andrewNZ
2487 posts

Uber Geek
+1 received by user: 1461
Inactive user


  #1055783 29-May-2014 11:29
Send private message

Remember powerline speeds are split across all powerline devices, so whether you have 2 units or 9 units you can still only have a total combined throughput of 300MB/s (or whatever the spec is).

cdrnet
92 posts

Master Geek
+1 received by user: 2


  #1055786 29-May-2014 11:37
Send private message

andrewNZ: Remember powerline speeds are split across all powerline devices, so whether you have 2 units or 9 units you can still only have a total combined throughput of 300MB/s (or whatever the spec is).


I'm just going to try P2P for one device. Will let you guys know how it plays out (c8




Why, oh why, oh why, won't this work )c8



RunningMan
9187 posts

Uber Geek
+1 received by user: 4840


  #1057775 2-Jun-2014 08:36
Send private message

Oooh, look.

A 10BaseT hub with a 10Base2 (coax) port. Those were the days ;-)

http://www.trademe.co.nz/Browse/Listing.aspx?id=736664338

cdrnet
92 posts

Master Geek
+1 received by user: 2


  #1057821 2-Jun-2014 10:43
Send private message

RunningMan: Oooh, look.

A 10BaseT hub with a 10Base2 (coax) port. Those were the days ;-)

http://www.trademe.co.nz/Browse/Listing.aspx?id=736664338


Yip, that was my era. The stress of finding failure intermittent failure points on a customer's 15 node network was no fun at all. Sticking pins in yourself might be slightly less stressful. 

I purchased so may bad cables that I started making them all myself. Used to make them in slow time and to exact measured sizes. Good fun.... I suppose. I may have some Ts and terminators hanging around if anyone wants them? (assuming I can find them of course). 




Why, oh why, oh why, won't this work )c8

floydie
474 posts

Ultimate Geek
+1 received by user: 49


  #1058146 2-Jun-2014 18:49
Send private message

why not just run some outdoor cat5 or 6 around the outside of the house and punch into the room wher you need it.?
its not like you need to bury it super deep.

 
 
 

Shop on-line at New World now for your groceries (affiliate link).
cdrnet
92 posts

Master Geek
+1 received by user: 2


  #1058166 2-Jun-2014 19:44
Send private message

floydie: why not just run some outdoor cat5 or 6 around the outside of the house and punch into the room wher you need it.?
its not like you need to bury it super deep.


I think the issue here is that there is already a 10 base T infrastructure.

I looked at the option of punching a couple of holes in the wall and then running the cable in the mortar recess. The 500Mb/s Powerline adapter option won that argument.




Why, oh why, oh why, won't this work )c8

MikeAqua

8031 posts

Uber Geek
+1 received by user: 3820


  #1058171 2-Jun-2014 19:58
Send private message

No 10 base T in place, just coax for satellite. Plan was to this as a LAN connection with some values either end to connect to regular ethernet cable.

The 10 base discussion was a bit of tangential nostalgia for a few.

I did think of running some cat 6 outside.

The cladding system is a cavity system and not simple to penetrate in a water right manner. It is under a weather tightness warranty so penetration would have to be by a certified installer to retain warranty coverage.




Mike


1 | 2 | 3 
Filter this topic showing only the reply marked as answer View this topic in a long page with up to 500 replies per page Create new topic








Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.