Sensors for the Entire House

Forums › Gadgets, robotics, home automation, electronics (including wearables) › Sensors for the Entire House

LennonNZ

2459 posts

Uber Geek

ID Verified

Trusted

#195838 7-May-2016 22:03

I am slowly getting my house automated.

I've had for a number of years my whole house with Apple HUE Bulbs so I can turn off/change individually any light in the whole house.

What I am missing is Sensors (or some other way) which is not too expensive to know where I (or a device I have with me). Ie go into the bathroom and the lights come on.. After it seems no movement turn it off etc.

Any suggestions? Somethings I can put in the whole house/all the rooms and then I can write rules on what to do when it seems movement.

Triangulate on a bluetooth/wifi/BLE signal? IR? RFID? iBeacon (http://estimote.com/)

jnimmo

1097 posts

Uber Geek

#1548078 7-May-2016 22:13

I'm looking at putting in a few of the Aeotec Z-Wave motion sensors http://aeotec.com/z-wave-sensor

Probably need some sort of Z-wave controller though to interface with the Philips Hue

Hopefully one can do a local interface rather than via internet API which some seem to do

SumnerBoy

2074 posts

Uber Geek

ID Verified

Lifetime subscriber

#1548127 8-May-2016 01:02

Unless you already have home alarm PIR sensors I think the best options are the Fibaro Motion sensor or Aeon Labs MultiSensor 6. These things are tiny, the batteries last well over a year if you configure them correctly, and they are very reliable (IME). The reason I mention home alarm PIR sensors is that they are probably the best method of motion detection since they are hard wired (no batteries), good quality PIRs. By chucking a Fibaro Universal Binary sensor in your alarm panel you can monitor two PIRs per Binary Sensor which allows them to serve a dual purpose - alarm sensor when the alarm is armed, and motion detection when you are home and the alarm is disarmed.

Of course anything Z-Wave based requires a controller but the cheapest option, a USB Z-Stick + Rasp Pi is pretty cost effective.

jnimmo

1097 posts

Uber Geek

#1548160 8-May-2016 07:53

Good point about the PIRs. I was also wondering about installing PIRs and there is a book on Arduino which shows how to wire them up for a home alarm or motion sensing, just would need X analog input pins to interface with X PIRs

Stu

Hammered
8335 posts

Uber Geek

Moderator

ID Verified

Trusted

Lifetime subscriber

#1548182 8-May-2016 08:54

Or go the easy route?

http://www.bunnings.co.nz/arlec-security-sensor-ceiling-360-angle-white_p04370674

People often mistake me for an adult because of my age.

Keep calm, and carry on posting.

Referral Links: Sharesies - Backblaze -

Are you happy with what you get from Geekzone? If so, please consider supporting us by subscribing.

No matter where you go, there you are.

cisconz

cisconz
1341 posts

Uber Geek

ID Verified

Trusted

Lifetime subscriber

#1548202 8-May-2016 10:19

A good alarm panel will output all sensors via RS232

Hmmmm

itxtme

2102 posts

Uber Geek

#1548244 8-May-2016 11:27

LennonNZ:

Triangulate on a bluetooth/wifi/BLE signal? IR? RFID? iBeacon (http://estimote.com/)

Triangulation would be overkill with beacons as walls will likely give enough disruption to ensure a low RSSI on a beacon when within a specific room. Estimote are fine, but expensive - lots of other suppliers, Radbeacon for example does an excellent coin cell beacon for $12 US. If you did go the beacon route you would need to carry your phone everywhere (this is what interacts and does what you need when it sees the beacon). In a lot of ways the movement sensors in the home environment are a much better fix.

jnimmo

1097 posts

Uber Geek

#1548247 8-May-2016 11:40

Like the alarm panel idea, where can I buy one from to install myself though? maybe a DSC

Quic Broadband

Move to New Zealand's best fibre broadband service (affiliate link). Note that to use Quic Broadband you must be comfortable with configuring your own router.

LennonNZ

2459 posts

Uber Geek

ID Verified

Trusted

#1548257 8-May-2016 12:29

I already have an alarm in the house with sensors but the sensors are only placed in areas which have entries so I would think useless for knowing where someone is , only useful to know if someone was in the house.

I'll look at the Alarm and see if I can get it to output if I sensors goes off.

cisconz

cisconz
1341 posts

Uber Geek

ID Verified

Trusted

Lifetime subscriber

#1548261 8-May-2016 12:43

You can always add more sensors - and if the panel itself doesn't support it, a panel upgrade (Replace the PCB and Keypad, but keep existing sensors and cabling etc) is usually easy to complete.

Hmmmm