[WXC/VFX] Locking down SIP traffic

Forums › One New Zealand (including Vodafone, WxC, Farmside) › [WXC/VFX] Locking down SIP traffic

gchiu

1211 posts

Uber Geek

Trusted

#148795 1-Jul-2014 10:57

I just noticed that I have about 13Gb of traffic at my remote office where I am about once a month.
It is corresponding to SIP traffic according to my Asterisk logs.
But my xport portal is showing no phone calls being made.

Is there a way I can block SIP traffic except between WXC and my office?

I am running fail2ban on the asterisk box. And between the asterisk box and internet is just an ADSL modem.

Is there anything else I can do to stop incurring all this traffic and charges arising there from?

I did call tech support and they said they can't do anything about this, they can't even confirm that it is SIP traffic. The guy said he though it was unlikely since it was mainly uploading but all I have is just the Asterisk box, and a truenet probe installed.

Thanks

1 | 2 | 3 | 4

30853 posts

Uber Geek

Retired Mod

Trusted

Biddle Corp

Lifetime subscriber

#1077705 1-Jul-2014 11:28

You should never have port 5060 exposed to the internet unless you understand the risks - presumably you do have it exposed.

Either remove the port forward or enable iptables on the PBX or your firewall.

gchiu

1211 posts

Uber Geek

Trusted

#1077739 1-Jul-2014 12:11

If I don't have port 5060 open, how do I get a connection with VFX?

I have fail2ban which I thought modifies iptables.

Ragnor

8223 posts

Uber Geek

Trusted

#1077800 1-Jul-2014 12:55

gchiu: If I don't have port 5060 open, how do I get a connection with VFX?

STUN, TURN, Far End Nat Traversal, Keep Alive Packets.

Ragnor

8223 posts

Uber Geek

Trusted

#1077806 1-Jul-2014 12:59

gchiu: between the asterisk box and internet is just an ADSL modem.

What is the make/model of the modem? Does it allow you to specify a src address on the port forward?

gchiu

1211 posts

Uber Geek

Trusted

#1077808 1-Jul-2014 13:02

I think I'm using a cheap one port adsl2 modem, and I think I got one with full cone nat. But since the office is 200 miles north of me, hard for me to check

Does WXC or anyone else have a best practice document on how to secure an Asterisk server when using VFX?

PS: just checked my invoices, it's a Netcomm NB14 one port ADSL2+ modem/router. I'll need to find an online manual.

Ragnor

8223 posts

Uber Geek

Trusted

#1077814 1-Jul-2014 13:06

WXC can only realistically support a managed solution they provide, if you decide to do you own thing with Asterisk it's up to you to configure/manage it.

gchiu

1211 posts

Uber Geek

Trusted

#1077830 1-Jul-2014 13:18

Just wondering how hard it would be for them to block port 5060 to everyone except themselves.

At this point I think I'll just shut the server down.

Quic Broadband

Move to New Zealand's best fibre broadband service (affiliate link). Free setup code: R587125ERQ6VE. Note that to use Quic Broadband you must be comfortable with configuring your own router.

michaelmurfy

meow
13260 posts

Uber Geek

Moderator

ID Verified

Trusted

Lifetime subscriber

#1077836 1-Jul-2014 13:22

gchiu: I think I'm using a cheap one port adsl2 modem, and I think I got one with full cone nat. But since the office is 200 miles north of me, hard for me to check

Does WXC or anyone else have a best practice document on how to secure an Asterisk server when using VFX?

PS: just checked my invoices, it's a Netcomm NB14 one port ADSL2+ modem/router. I'll need to find an online manual.

What kind of ADSL router? Cheap ones often have some pretty dodgy exploits.

Michael Murphy | https://murfy.nz
Referral Links: Quic Broadband (use R122101E7CV7Q for free setup)

Are you happy with what you get from Geekzone? Please consider supporting us by subscribing.
Opinions are my own and not the views of my employer.

sbiddle

30853 posts

Uber Geek

Retired Mod

Trusted

Biddle Corp

Lifetime subscriber

#1077853 1-Jul-2014 13:29

gchiu: If I don't have port 5060 open, how do I get a connection with VFX?

I have fail2ban which I thought modifies iptables.

Port 5060 doesn't need to have a port forward because of the basic way a router works - when traffic goes out it creates a NAT pinhole allowing traffic back in from the same source, in exactly the same way you don't need to create a port forward for web browsing to work.

If you have issues with UDP timeouts with the NAT pinhole being closed something like options=yes will send a SIP "ping" every so often which will keep the pinhole open.

fail2ban will simply monitor asterisk logs and create iptables blocking rules.

sbiddle

30853 posts

Uber Geek

Retired Mod

Trusted

Biddle Corp

Lifetime subscriber

#1077855 1-Jul-2014 13:30

gchiu: Just wondering how hard it would be for them to block port 5060 to everyone except themselves.

At this point I think I'll just shut the server down.

WxC (like any other ISP) isn't going to create a firewall for end customers, this is something you need to manage at your end.

chevrolux

4962 posts

Uber Geek
Inactive user

#1077856 1-Jul-2014 13:31

If you must port forward at least have a firewall rule blocking traffic from anything other than your provider's proxy. Even with fail2ban in place there is still traffic hitting your router which you are being charged for.

Otherwise with standard SIP registration it isn't required. Just have it registering regular and use keep-alive's.

gchiu

1211 posts

Uber Geek

Trusted

#1077918 1-Jul-2014 14:23

It's a couple of years ago since I set this up, and I've pretty much forgotten what I did.
I think I had an issue with no sound if I didn't port forward but since I don't have access to the server I can't be sure.

I don't allow anonymous sip connections.

Even if I have a firewall setup, presumably I still can't stop them hitting my address and causing some traffic.

Since I only visit the office once a month, I think I'll just setup another mirrow server in Wgton to which I have local access.
And only turn on the office remote server when I'm there.

grudge

266 posts

Ultimate Geek

#1078059 1-Jul-2014 16:41

Any chance you can setup a tcpdump on that interface and see what this traffic is ?

13GB is a hell of a lot of traffic for voip, it would have to be RTP (voice) and you'd expect to see similar amounts both up and down if it was a phone conversation passing media both ways.

gchiu

1211 posts

Uber Geek

Trusted

#1078122 1-Jul-2014 17:59

Well, it looks like I did setup ssh over hamachi to this server so I am now running tcpdump -i eth0 -c 100000 -w capture.log

and will see what happens. I will capture Hamachi traffic though, so need a way to filter that out.

Already my xport portal shows 40 mb of traffic today when there should be nothing running.

Ragnor

8223 posts

Uber Geek

Trusted

#1078156 1-Jul-2014 18:57

How much data do you have TrueNet configured to use? You can adjust that in their website for your account.

1 | 2 | 3 | 4