Geekzone: technology news, blogs, forums
Guest
Welcome Guest.
You haven't logged in yet. If you don't have an account you can register now.




'That VDSL Cat'
7125 posts

Uber Geek
+1 received by user: 1400

Trusted
Spark
Subscriber

Topic # 226296 30-Dec-2017 13:49
Send private message quote this post

Hey all,

 

 

 

looking at those of you who are more of an expert using mikroteks (TB951G-2HnD in this case)

 

What I'm looking to do with this configuration is pretty basic. (I have stripped it back to the mare basics in this case)

 

  • Create VLAN20, bridge this to a wlan2 interface
  • Untag traffic going out Eth2
  • Run a static ip on Eth2/bridge1 for remote access

 

 

 

 

At this stage, VLAN20 over bridge1 passes nicely to untagged traffic on Eth2 (bridging no IP Routing)

 

If i assign an ip to Eth1,3,4,5 routing to the network is possible (ping off the routerboard/to the routerboard).

 

If i assign an ip to Eth2, It assigns in the routing table as bridge1; Much like it does with bridge/eth1,3,4,5 However, there is no traffic passing.

 

 

 

I'm more than likely over-complicating this, but at a later date eth2 wouldn't be untagging but rather being trunked vlan20 already from my 3011 - In writing this I'm considering setting up the 3011 to pass this and see if the magic bullet is removing the whole untagging situation...

 

 

 

Have i missed something simple to assign an ip to the routerboard, on this second bridge?

 

Would be simple to just use two links, but that is not ideal in this situation (Routerboard is intended to be on the edge trunking traffic, thus it would only have a single uplink to the core)

 

Current running conf - https://pastebin.com/RZjmshPp





#include <std_disclaimer>

 

Any comments made are personal opinion and do not reflect directly on the position my current or past employers may have.


Create new topic
4625 posts

Uber Geek
+1 received by user: 1395


  Reply # 1927013 30-Dec-2017 14:53
Send private message quote this post

Perhaps change

 

add address=10.3.57.211/24 interface=ether2 network=10.3.57.0 to

 

add address=10.3.57.211/24 interface=bridge1 network=10.3.57.0

 

to assign the address to the second bridge, not the port.




'That VDSL Cat'
7125 posts

Uber Geek
+1 received by user: 1400

Trusted
Spark
Subscriber

  Reply # 1927026 30-Dec-2017 15:27
Send private message quote this post

RunningMan:

 

Perhaps change

 

add address=10.3.57.211/24 interface=ether2 network=10.3.57.0 to

 

add address=10.3.57.211/24 interface=bridge1 network=10.3.57.0

 

to assign the address to the second bridge, not the port.

 

 

routeros itself actually smartly translates ether2 to bridge1 in the routing table.

 

 

 

Did give this one a shot however

 

For what i wanna do, i suspect i goofed by opting for RouterOS over SwitchOS

 

Figured reproducing port switching with bridges would allow binding a WLAN interface alongside the switch (within the same device as DC power is my constraint)





#include <std_disclaimer>

 

Any comments made are personal opinion and do not reflect directly on the position my current or past employers may have.


 
 
 
 




'That VDSL Cat'
7125 posts

Uber Geek
+1 received by user: 1400

Trusted
Spark
Subscriber

  Reply # 1927027 30-Dec-2017 15:39
Send private message quote this post

Suppose i'll rephrase that question.

 

 

 

Have i chosen the wrong platform to achieve this?

 

  • Trunk 6-8 vlans
  • QinQ for 4 vlans (or retag vlan on exit to new vlan/untag)

 

 

 

 

As i dig into it more, looks like switchos out of the box does both these features alot more simpler.

 

Based on that, i'd say i'm possibly better off going with a 260GSP paired with a mAP - using the PoE output to keep things clean.

 

 

 

 

 

Who would have thought, making a router act like a switch would be so complicated - i assumed SwOS to be essentially build in not stripped out.





#include <std_disclaimer>

 

Any comments made are personal opinion and do not reflect directly on the position my current or past employers may have.


Create new topic



Twitter »

Follow us to receive Twitter updates when new discussions are posted in our forums:



Follow us to receive Twitter updates when news items and blogs are posted in our frontpage:



Follow us to receive Twitter updates when tech item prices are listed in our price comparison site:





News »

CPTPP text and National Interest Analysis released for public scrutiny
Posted 21-Feb-2018 19:43


Foodstuffs to trial digitised shopping trolleys
Posted 21-Feb-2018 18:27


2018: The year of zero-login, smart cars & the biometrics of things
Posted 21-Feb-2018 18:25


Intel reimagines data centre storage with new 3D NAND SSDs
Posted 16-Feb-2018 15:21


Ground-breaking business programme begins in Hamilton
Posted 16-Feb-2018 10:18


Government to continue search for first Chief Technology Officer
Posted 12-Feb-2018 20:30


Time to take Appleā€™s iPad Pro seriously
Posted 12-Feb-2018 16:54


New Fujifilm X-A5 brings selfie features to mirrorless camera
Posted 9-Feb-2018 09:12


D-Link ANZ expands connected smart home with new HD Wi-Fi cameras
Posted 9-Feb-2018 09:01


Dragon Professional for Mac V6: Near perfect dictation
Posted 9-Feb-2018 08:26


OPPO announces R11s with claims to be the picture perfect smartphone
Posted 2-Feb-2018 13:28


Vocus Communications wins a place on the TaaS panel
Posted 26-Jan-2018 15:16


SwipedOn raises $1 million capital
Posted 26-Jan-2018 15:15


Slingshot offers unlimited gigabit fibre for under a ton
Posted 25-Jan-2018 13:51


Spark doubles down on wireless broadband
Posted 24-Jan-2018 15:44



Geekzone Live »

Try automatic live updates from Geekzone directly in your browser, without refreshing the page, with Geekzone Live now.



Are you subscribed to our RSS feed? You can download the latest headlines and summaries from our stories directly to your computer or smartphone by using a feed reader.

Alternatively, you can receive a daily email with Geekzone updates.